149 Commits

Author	SHA1	Message	Date
Bassam	be9b47ece2	Update printer.cfg ... Adjust `sense_resistor` values to 0.110 according to BTT wiki: https://bttwiki.com/TMC2209.html#standalone-mode-vref-setting.	2025-06-16 14:03:21 -04:00
Bassam Husain	1512fc6606	Adjust skr wiring diagram to include filament sensor. Adjust printer.cfg and misc-macros.cfg accordingly.	2024-05-15 02:36:42 -04:00
Bassam Husain	671e2ec375	Merge branch 'master' into skr-mini-e3-v3	2023-12-08 01:09:32 -05:00
Bassam Husain	c82fbedcd7	Adjust comment in printer.cfg.	2023-12-03 04:44:10 -05:00
Bassam Husain	121a7b9278	Merge branch 'master' into skr-mini-e3-v3	2023-11-27 02:00:52 -05:00
Bassam Husain	b2d13a4438	Add comments to printer.cfg.	2023-11-27 01:24:38 -05:00
Bassam Husain	4583e008ab	Add axis_twist_compensation.	2023-11-24 19:52:27 -05:00
Bassam Husain	18552711c5	Adjust printer.cfg: axis_twist_compensation section.	2023-11-24 18:56:57 -05:00
Bassam Husain	9ded9c0d86	Merge branch 'master' into skr-mini-e3-v3	2023-11-23 04:47:25 -05:00
Bassam Husain	8347290f9f	Adjust kamp settings: include line_purge; adjust printer.cfg accordingly; adjust readme.md, slicer and kamp sections.	2023-11-23 04:36:15 -05:00
Bassam Husain	3d4403957e	Adjust printer.cfg skr.	2023-11-19 23:01:08 -05:00
Bassam Husain	9dda49ce18	Merge branch 'master' into skr-mini-e3-v3	2023-09-13 18:37:04 -04:00
Bassam Husain	42bab87f6b	Adjust extruder.max_extrude_cross_section.	2023-09-13 18:36:37 -04:00
Bassam Husain	deb40aee58	Merge branch 'master' into skr-mini-e3-v3	2023-09-10 15:07:27 -04:00
Bassam Husain	5979673f54	Fix calibrate esteps link, and add accompanying everything-sv06 link. Adjust calibration.cfg to turn off print cooling fan after pid tune hotend.	2023-09-07 00:59:57 -04:00
Bassam Husain	54b2f42da8	Merge branch 'master' into skr-mini-e3-v3	2023-08-13 16:12:28 -04:00
Bassam Husain	cbeb15a272	Adjusted bed_mesh.mesh_min.	2023-08-07 23:43:07 -04:00
Bassam Husain	6fe0cdc1d7	Merge branch 'master' into skr-mini-e3-v3	2023-08-05 02:00:34 -04:00
Bassam Husain	c9a469d677	Merge branch 'develop', KAMP code. Restructured osskc code.	2023-07-28 02:43:12 -04:00
Bassam Husain	f90b3842e4	Adjusted screws_tilt_adjust section.	2023-07-02 21:39:21 -04:00
Bassam Husain	49ed59dc14	Adjusted screws_tilt_adjust section.	2023-07-02 21:36:49 -04:00
Bassam Husain	d343f37e15	Merge branch 'master' into skr-mini-e3-v3	2023-07-01 01:42:20 -04:00
Bassam Husain	d405db4922	Adjusted mcu section.	2023-06-21 18:18:21 -04:00
Ed Ropple	12ed1d3a9f	replaced manual PID/calibration steps with reusable macros	2023-06-20 18:28:50 -04:00
Bassam Husain	622ce6714b	Skr-mini-e3-v3: set x, y, z run_current: 0.600. Added note about stepper motor run_current.	2023-05-10 22:00:45 -04:00
Bassam Husain	149f628c1e	Change microsteps: 64 for skr-mini-e3-v3.	2023-05-09 18:56:58 -04:00
Bassam Husain	8b941129b0	Adjust driver_SGTHRS.	2023-04-26 16:25:07 -04:00
Bassam Husain	d4b9849f78	Merge branch 'master' into skr-mini-e3-v3	2023-04-26 13:17:52 -04:00
Björn Marschollek	4df5ef2db3	Add config for 2 ADXL345 via RasPi pico ... This adds a configuration supporting two ADXL345 sensors at the same time though a Raspberry Pi pico. Resonance measurements for both the head and the bed can be done without having to change the sensors.	2023-04-21 20:26:11 +02:00
Bassam Husain	297ce7b437	Reversed stepper_x.dir_pin.	2023-04-13 17:41:33 -04:00
Bassam Husain	1a5c935c54	Merging with master.	2023-04-07 10:00:31 -04:00
Bassam Husain	953daefa32	Adjusted PRINT_START sequence to save time, and to prevent oozing. Increased microsteps to 128, and added square_corner_velocity.	2023-04-07 09:52:06 -04:00
Bassam Husain	4f499a72f5	Update printer.cfg ... Set extruder.microsteps to 64.	2023-04-06 07:10:31 -04:00
Bassam Husain	ab339294b9	Simplified and made clear instructions on skr-mini-e3-v3 branch.	2023-04-02 22:50:23 -04:00
Bassam Husain	dba8b85da6	Getting skr-e3-v3 inline with master.	2023-04-02 22:24:21 -04:00
Bassam Husain	39131e0d66	Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware	2023-04-02 11:08:47 -04:00
Bassam Husain	5142687f98	Merge branch 'master' into skr-mini-e3-v3	2023-03-26 07:13:01 -04:00
Bassam Husain	c2bd1fa076	More changes pulled from personal. Added filament sensor pinout.	2023-03-14 19:47:16 -04:00
Bassam Husain	64a6f98fe4	Pulling in structure from personal branch.	2023-03-14 18:36:53 -04:00
Bassam Husain	c20f18280c	Changed extruder microsteps to 64.	2023-03-14 01:26:12 -04:00
Bassam Husain	5ccabd1a3d	Added conditional beeping.	2023-03-12 01:53:44 -05:00
Bassam Husain	69a5cbc45c	Merging filament sensor related code.	2023-03-12 01:32:40 -05:00
Bassam Husain	3c84c049c8	Rearranged beeper section.	2023-03-11 23:19:47 -05:00
Bassam Husain	c6d484cce1	Pulled in printer.cfg from master.	2023-03-11 21:37:25 -05:00
Bassam Husain	e972231cd1	Added not about e-steps.	2023-03-11 19:47:18 -05:00
Bassam Husain	47b6c370a0	Merge branch 'structure' into personal	2023-03-11 19:44:33 -05:00
Bassam Husain	110c84f451	Added headings for sections in printer.cfg.	2023-03-10 05:39:51 -05:00
Bassam Husain	bccf585446	Pulled in changes from master.	2023-03-10 05:30:53 -05:00
Bassam Husain	7f05e62e94	Removed pressure_advance.	2023-03-10 05:13:50 -05:00
Bassam Husain	95dbb44ad2	Merge branch 'master' into personal	2023-03-10 05:08:56 -05:00