mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 21:41:15 +00:00
Getting skr-e3-v3 inline with master.
This commit is contained in:
Bassam Husain
229
printer.cfg
229
printer.cfg
@@ -1,229 +0,0 @@
|
||||
# This file contains pin mappings for the stock Sovol SV06.
|
||||
#
|
||||
# Find installation instructions at https://github.com/bassamanator/Sovol-SV06-firmware
|
||||
#
|
||||
# See https://www.klipper3d.org/Config_Reference.html for configuration reference.
|
||||
|
||||
[include ./cfgs/misc-macros.cfg]
|
||||
[include ./cfgs/PARKING.cfg]
|
||||
[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
|
||||
|
||||
# NOTE Uncomment the ONE of the following lines if you're using an adxl345
|
||||
# [include ./cfgs/adxl-rp2040.cfg]
|
||||
# [include ./cfgs/adxl-direct.cfg]
|
||||
|
||||
[mcu]
|
||||
# NOTE Obtain definition by "ls -l /dev/serial/by-id/"
|
||||
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 200
|
||||
max_accel: 3000
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 45
|
||||
|
||||
#####################################################################
|
||||
# X/Y/Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 64
|
||||
rotation_distance: 40
|
||||
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
||||
position_endstop: 0
|
||||
position_max: 223 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 40
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_x]
|
||||
uart_pin: PC1
|
||||
run_current: 0.860
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
driver_SGTHRS: 81
|
||||
diag_pin: PA5
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 64
|
||||
rotation_distance: 40
|
||||
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
||||
position_endstop: 0
|
||||
position_max: 223 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 40
|
||||
homing_retract_dist: 0
|
||||
|
||||
[tmc2209 stepper_y]
|
||||
uart_pin: PC0
|
||||
run_current: 0.900
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
driver_SGTHRS: 81
|
||||
diag_pin: PA6
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 64
|
||||
rotation_distance: 4
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_min: -4
|
||||
position_max: 258 # NOTE You can adjust this if you have more room
|
||||
homing_speed: 5
|
||||
|
||||
[tmc2209 stepper_z]
|
||||
uart_pin: PA15
|
||||
run_current: 1.000
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
diag_pin: PA7
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 64
|
||||
rotation_distance: 4.65 # NOTE Calibrate e-steps and adjust https://www.klipper3d.org/Rotation_Distance.html
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
control: pid
|
||||
pid_kd: 86.991
|
||||
pid_kp: 21.479
|
||||
pid_ki: 1.326
|
||||
min_temp: 0
|
||||
max_temp: 300
|
||||
max_extrude_only_distance: 150.0
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: PC14
|
||||
run_current: 0.550
|
||||
stealthchop_threshold: 0
|
||||
interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_kp: 64.440
|
||||
pid_ki: 0.773
|
||||
pid_kd: 1343.571
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
|
||||
#####################################################################
|
||||
# Probe Related
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
pin: PB1
|
||||
x_offset: 27
|
||||
y_offset: -20
|
||||
z_offset: 0
|
||||
samples: 3
|
||||
samples_result: median
|
||||
samples_tolerance: 0.01
|
||||
samples_tolerance_retries: 5
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 84.50, 135 # NOTE The probe is at the center of the bed.
|
||||
speed: 100.0
|
||||
z_hop: 10
|
||||
z_hop_speed: 15
|
||||
|
||||
[bed_mesh]
|
||||
speed: 175
|
||||
mesh_min: 27, 5
|
||||
mesh_max: 222, 203
|
||||
probe_count: 5,5
|
||||
algorithm: bicubic
|
||||
fade_start: 1
|
||||
fade_end: 10
|
||||
fade_target: 0
|
||||
|
||||
#####################################################################
|
||||
# Fans
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
#####################################################################
|
||||
# Misc
|
||||
#####################################################################
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PB12
|
||||
sclk_pin: PB13
|
||||
sid_pin: PB15
|
||||
encoder_pins: ^PB14, ^PB10
|
||||
click_pin: ^!PB2
|
||||
|
||||
[bed_screws]
|
||||
screw1: 26.5, 31
|
||||
screw1_name: front left
|
||||
screw2: 196.75, 31
|
||||
screw2_name: front right
|
||||
screw3: 196.75, 201
|
||||
screw3_name: back right
|
||||
screw4: 26.5, 201
|
||||
screw4_name: back left
|
||||
|
||||
[screws_tilt_adjust]
|
||||
screw1: 111.5, 116.5
|
||||
screw1_name: center
|
||||
screw2: 26.5, 31
|
||||
screw2_name: front left
|
||||
screw3: 196.75, 31
|
||||
screw3_name: front right
|
||||
screw4: 196.75, 201
|
||||
screw4_name: back right
|
||||
screw5: 26.5, 201
|
||||
screw5_name: back left
|
||||
speed: 50
|
||||
horizontal_move_z: 10
|
||||
screw_thread: CCW-M4
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PC6
|
||||
value: 0
|
||||
shutdown_value: 0
|
||||
pwm: True
|
||||
cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
|
||||
|
||||
# [filament_switch_sensor filament_sensor]
|
||||
# switch_pin: !PA4 # "Pulled-high"
|
||||
# pause_on_runout: True
|
||||
# insert_gcode:
|
||||
# M117 Insert Detected
|
||||
# runout_gcode:
|
||||
# M117 Runout Detected
|
||||
# CONDITIONAL_BEEP i=3 dur=300 freq=400
|
||||
Reference in New Issue
Block a user