Bassam Husain
1cdcb4934b
PRINT_START adjust: don't cooldown if not necessary.
2023-04-22 07:10:06 -04:00
Björn Marschollek
835e990d88
Avoid cooling down the extruder in PRINT_START
...
The current `PRINT_START` macro heats the extruder to 150 degrees, then
to 170, and finally to the target temperature. If the extruder is
already hot, this unnecessarily cools it down and wastes time.
This change only cools down the hotend if it's above the target
temperature and then only to that temperature.
If the extruder was colder than 150 degrees, this change maintains the
current behaviour.
2023-04-22 12:20:01 +02:00
Bassam Husain
51fd3f0b19
Update adxl-rpi-pico-2x.cfg
...
Minor adjustments to adxl-rpi-pico-2x.cfg.
2023-04-21 16:41:26 -04:00
Björn Marschollek
4df5ef2db3
Add config for 2 ADXL345 via RasPi pico
...
This adds a configuration supporting two ADXL345 sensors at the same
time though a Raspberry Pi pico.
Resonance measurements for both the head and the bed can be done without
having to change the sensors.
2023-04-21 20:26:11 +02:00
Bassam Husain
23d24aab17
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-20 17:09:58 -04:00
Bassam Husain
498e0d4a4d
PRINT_START bedtemp fix, 2nd try.
2023-04-20 16:56:25 -04:00
Björn Marschollek
4a38d34a0e
Add a minimum bed temperature of 0 degrees
...
If the bed temperature is less than 2, the print job fails with an
error message complaining about an invalid temperature. This happens,
for instance, when printing ABS where the bed is not supposed to be
heated.
This change makes sure that the bed temperature cannot be negative.
2023-04-20 22:53:19 +02:00
Bassam Husain
9b712df594
PRINT_START bedtemp fix.
2023-04-20 16:43:43 -04:00
Bassam Husain
e888ac0882
Added orange pi temp section.
2023-04-20 12:37:03 -04:00
Bassam Husain
5e342261c8
Pulling in print_start from personal branch.
2023-04-20 12:19:06 -04:00
Bassam Husain
89fbb10154
variable_pre_purge_prime_length reverted.
2023-04-20 12:10:00 -04:00
Bassam Husain
6eb152e58d
Adjust PRINT_START: safe_z_home startX, startY.
2023-04-19 10:53:08 -04:00
Bassam Husain
2e5764f295
Adjusted print_start start x, y positions conditionally.
2023-04-18 10:39:22 -04:00
Bassam Husain
7e5aeb6654
Print_start adjusted.
2023-04-17 02:13:19 -04:00
Bassam Husain
f5d3499da7
Getting safe_z_home info in print_start.
2023-04-17 01:02:20 -04:00
Bassam Husain
2c8a4e5aa0
Print_start improvements.
2023-04-17 00:55:51 -04:00
Bassam Husain
807c91507a
Pulling in from personal branch.
2023-04-17 00:41:03 -04:00
Bassam Husain
a30d367d1d
Commented out raspberry pi temperature section.
2023-04-17 00:21:03 -04:00
Bassam Husain
b8d246762f
Added print_start heating.
2023-04-14 07:39:46 -04:00
Bassam Husain
9fc09eef43
Added more steps to heating in print_start.
2023-04-13 19:48:11 -04:00
Bassam Husain
02eb713930
Added more steps to heating in print_start.
2023-04-13 18:06:36 -04:00
Bassam Husain
5abaf73b9c
Comment cleanup in print_end.
2023-04-13 17:32:44 -04:00
Bassam Husain
238091d860
Minor speedup in print_start.
2023-04-13 17:28:55 -04:00
Bassam Husain
f0729bfc2e
New z_offset.
2023-04-11 15:54:19 -04:00
Bassam Husain
6dc119cf99
Added pause/runout/m600 to faq. Reduced speed in print_start.
2023-04-07 19:44:30 -04:00
Bassam Husain
953daefa32
Adjusted PRINT_START sequence to save time, and to prevent oozing. Increased microsteps to 128, and added square_corner_velocity.
2023-04-07 09:52:06 -04:00
Bassam Husain
d53a6d822a
Adjusted PRINT_START: travel speeds.
2023-04-06 09:31:15 -04:00
Bassam Husain
3f06eebe42
Adjusted PRINT_START temperature heating sequence.
2023-04-06 09:16:18 -04:00
Bassam Husain
f9832b60c3
Adjusted print_start to start heating first, then home x and y.
2023-04-02 20:38:14 -04:00
Bassam Husain
8346c79f35
Adjusted start position for purge_line.
2023-04-02 19:00:47 -04:00
Bassam Husain
1805a999b1
Adjusted start position for purge_line.
2023-04-02 18:47:41 -04:00
Bassam Husain
98a1cd7fe6
Purge_line macro adjusted to print at the front of the bed; printer agnostic. Print_end adjusted to use safer speed.
2023-04-02 18:31:58 -04:00
Bassam Husain
ad78f3f759
Merge branch 'purge' into personal
2023-03-27 17:02:55 -04:00
Bassam Husain
d227fcb58f
Re-added temperature_wait.
2023-03-27 16:57:42 -04:00
Bassam Husain
d08bbb7f23
Adjust purge_line.
2023-03-27 16:50:43 -04:00
Bassam Husain
c462eb819c
Adjust purge_line.
2023-03-26 15:04:35 -04:00
Bassam Husain
4528151bc1
Adjusted print_end to fix speed calculation error.
2023-03-26 14:35:04 -04:00
Bassam Husain
aff79ff8de
Merge remote-tracking branch 'origin/temp-ms' into personal
2023-03-26 14:24:43 -04:00
Bassam Husain
f12e2f3382
Adjusted print_end to use speeds pulled from config.
2023-03-26 14:16:24 -04:00
Bassam Husain
3c73cf3461
Removed temperature_wait. Increased microsteps to 128.
2023-03-24 03:12:40 -04:00
Bassam Husain
3551f307ae
Added beeping on colour/filament change.
2023-03-20 01:04:36 -04:00
Bassam Husain
f4ce4165d5
Added beeping on colour/filament change.
2023-03-20 01:02:56 -04:00
Bassam Husain
95897311e6
Filament runout sensor code merged.
2023-03-14 21:08:16 -04:00
Bassam Husain
c2bd1fa076
More changes pulled from personal. Added filament sensor pinout.
2023-03-14 19:47:16 -04:00
Bassam Husain
9239a54e8b
More changes pulled from personal.
2023-03-14 18:55:07 -04:00
Bassam Husain
c967be1023
More changes pulled from personal.
2023-03-14 18:45:30 -04:00
Bassam Husain
64a6f98fe4
Pulling in structure from personal branch.
2023-03-14 18:36:53 -04:00
Bassam Husain
150e1b7425
Removed CHECK_PRE_PURGE_PRIME_LENGTH
...
macro.
2023-03-12 14:35:13 -04:00
Bassam Husain
0b5909ab53
Added ADJUST_FILAMENT_SENSOR_STATUS use back.
2023-03-12 12:19:59 -04:00
Bassam Husain
c0f4eb76fc
Merge branch 'fix-sensor' into personal
2023-03-12 11:37:09 -04:00
