Bassam Husain
3131370ebf
Merge branch 'master' into any-printer
2023-09-13 17:26:17 -04:00
Bassam Husain
29df5b6cdd
Pulled in KAMP from upstream.
2023-09-13 17:04:28 -04:00
Bassam Husain
5979673f54
Fix calibrate esteps link, and add accompanying everything-sv06 link. Adjust calibration.cfg to turn off print cooling fan after pid tune hotend.
2023-09-07 00:59:57 -04:00
Bassam Husain
913f689768
Merge branch 'master' into any-printer
2023-08-27 20:16:44 -04:00
Bassam Husain
90dd8a1314
Adjust readme.md.
2023-08-27 20:05:03 -04:00
Bassam Husain
8c86edfc34
TEST_SPEED macro working.
2023-07-29 16:58:10 -04:00
Bassam Husain
c9a469d677
Merge branch 'develop', KAMP code. Restructured osskc code.
2023-07-28 02:43:12 -04:00
Bassam Husain
6595987d11
Pulled in calibration.cfg.
2023-07-01 02:47:54 -04:00
Bassam Husain
67307f5679
Adjust misc-macros.cfg, minor.
2023-07-01 02:44:47 -04:00
Bassam Husain
8a8229f6e8
Adjusted calibration.cfg to accept target temp.
2023-07-01 02:25:55 -04:00
Bassam Husain
3a6dab44e0
Pulling in minor changes in misc-macros.cfg.
2023-07-01 02:00:06 -04:00
Bassam Husain
d6f03f7a2c
Cleanup in misc-macros.cfg. Adjusted calibration.cfg to work dynamically.
2023-07-01 00:51:59 -04:00
Bassam Husain
d405db4922
Adjusted mcu section.
2023-06-21 18:18:21 -04:00
Bassam Husain
511fcbed57
Merge branch 'ed/calibration-tools'
2023-06-21 17:50:45 -04:00
Ed Ropple
12ed1d3a9f
replaced manual PID/calibration steps with reusable macros
2023-06-20 18:28:50 -04:00
Bassam Husain
759c81be69
Minor adjustment to misc-macros.cfg.
2023-06-19 01:04:18 -04:00
Bassam Husain
82be01a0e0
Pulled in from master.
2023-06-13 21:37:38 -04:00
Bassam Husain
5ada85f964
Bed temp over now customizable.
2023-06-09 17:28:07 -04:00
Bassam Husain
89d6c0d09f
Pulling in print_start from master branch.
2023-05-21 17:33:25 -04:00
Bassam Husain
24a4262af2
Pulled in print_start from personal: prints start with higher bed temp now, range 10C.
2023-05-20 19:59:18 -04:00
Bassam Husain
b83a7c96b7
Pulling in from master.
2023-04-23 15:47:29 -04:00
Bassam Husain
2cadcf65aa
Pulling in from master.
2023-04-23 15:44:04 -04:00
Bassam Husain
57e6755ced
Merge pull request #42 from muffix/dont-cool-down-in-print-start
...
Avoid cooling down the extruder in PRINT_START
2023-04-22 07:24:44 -04:00
Björn Marschollek
835e990d88
Avoid cooling down the extruder in PRINT_START
...
The current `PRINT_START` macro heats the extruder to 150 degrees, then
to 170, and finally to the target temperature. If the extruder is
already hot, this unnecessarily cools it down and wastes time.
This change only cools down the hotend if it's above the target
temperature and then only to that temperature.
If the extruder was colder than 150 degrees, this change maintains the
current behaviour.
2023-04-22 12:20:01 +02:00
Bassam Husain
51fd3f0b19
Update adxl-rpi-pico-2x.cfg
...
Minor adjustments to adxl-rpi-pico-2x.cfg.
2023-04-21 16:41:26 -04:00
Björn Marschollek
4df5ef2db3
Add config for 2 ADXL345 via RasPi pico
...
This adds a configuration supporting two ADXL345 sensors at the same
time though a Raspberry Pi pico.
Resonance measurements for both the head and the bed can be done without
having to change the sensors.
2023-04-21 20:26:11 +02:00
Bassam Husain
23d24aab17
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-20 17:09:58 -04:00
Björn Marschollek
4a38d34a0e
Add a minimum bed temperature of 0 degrees
...
If the bed temperature is less than 2, the print job fails with an
error message complaining about an invalid temperature. This happens,
for instance, when printing ABS where the bed is not supposed to be
heated.
This change makes sure that the bed temperature cannot be negative.
2023-04-20 22:53:19 +02:00
Bassam Husain
1ca3355dd7
Pulling in print_start from master branch.
2023-04-20 12:26:14 -04:00
Bassam Husain
5e342261c8
Pulling in print_start from personal branch.
2023-04-20 12:19:06 -04:00
Bassam Husain
572e768111
Pulling from master.
2023-04-18 08:02:11 -04:00
Bassam Husain
807c91507a
Pulling in from personal branch.
2023-04-17 00:41:03 -04:00
Bassam Husain
a30d367d1d
Commented out raspberry pi temperature section.
2023-04-17 00:21:03 -04:00
Bassam Husain
5abaf73b9c
Comment cleanup in print_end.
2023-04-13 17:32:44 -04:00
Bassam Husain
238091d860
Minor speedup in print_start.
2023-04-13 17:28:55 -04:00
Bassam Husain
6dc119cf99
Added pause/runout/m600 to faq. Reduced speed in print_start.
2023-04-07 19:44:30 -04:00
Bassam Husain
953daefa32
Adjusted PRINT_START sequence to save time, and to prevent oozing. Increased microsteps to 128, and added square_corner_velocity.
2023-04-07 09:52:06 -04:00
Bassam Husain
4c72bfe43e
Adjusted readme.
2023-04-02 19:26:26 -04:00
Bassam Husain
117766d1ad
Adjusted start position for purge_line.
2023-04-02 19:02:26 -04:00
Bassam Husain
8346c79f35
Adjusted start position for purge_line.
2023-04-02 19:00:47 -04:00
Bassam Husain
81558afd79
Pulled in purge_line and print_end from master.
2023-04-02 18:40:40 -04:00
Bassam Husain
98a1cd7fe6
Purge_line macro adjusted to print at the front of the bed; printer agnostic. Print_end adjusted to use safer speed.
2023-04-02 18:31:58 -04:00
Bassam Husain
c7bcbe863e
Added conditional beeping to MECHANICAL_GANTRY_CALIBRATION.cfg. Adjusted directory structure section in readme.md.
2023-03-27 18:26:21 -04:00
Bassam Husain
eb029fe891
Created any-printer branch.
2023-03-27 18:18:13 -04:00
Bassam Husain
3551f307ae
Added beeping on colour/filament change.
2023-03-20 01:04:36 -04:00
Bassam Husain
95897311e6
Filament runout sensor code merged.
2023-03-14 21:08:16 -04:00
Bassam Husain
c2bd1fa076
More changes pulled from personal. Added filament sensor pinout.
2023-03-14 19:47:16 -04:00
Bassam Husain
9239a54e8b
More changes pulled from personal.
2023-03-14 18:55:07 -04:00
Bassam Husain
c967be1023
More changes pulled from personal.
2023-03-14 18:45:30 -04:00
Bassam Husain
64a6f98fe4
Pulling in structure from personal branch.
2023-03-14 18:36:53 -04:00
