mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 13:31:16 +00:00
50 lines
3.2 KiB
Markdown
50 lines
3.2 KiB
Markdown
# 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration
|
|
|
|
## This branch contains the Klipper configuration and firmware for the Sovol SV06 3D printer with the `BTT SKR-Mini-E3-V3.0` motherboard.
|
|
|
|
## If you were looking for my OSS Klipper Configuration for the Sovol SV06 with *completely stock hardware*, please refer to the [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch.
|
|
|
|
## I am creating these files for my personal use and cannot be held responsible for what it might do to your printer.
|
|
|
|
## ❗☠️ I do not own this board so everything found on this branch is COMPLETELY UNTESTED ☠️❗
|
|
## ❗☠️ USE AT YOUR OWN RISK. YOU HAVE BEEN WARNED. ☠️❗
|
|
|
|
## An Important Note
|
|
|
|
⭐ A big thank you to Github user `transistor1`. This branch would not have been possible without his help. Please checkout his profile [here](https://github.com/transistor1). ⭐
|
|
|
|
## Installation Instructions
|
|
|
|
### Electronic Wiring
|
|
|
|
Wire cables according to the following diagram:
|
|
<img src="./misc/skr-mini/skr-mini-e3-v3.0-v1678580296384.png" alt='skr-mini-e3-v3.0 installation instructions'/>
|
|
### Download Firmware Precompiled by BIGTREETECH
|
|
- [firmware-USB.bin](./misc/skr-mini/firmware-USB.bin). Connect the SKR-Mini to the Raspberry Pi via USB connection.
|
|
- [firmware-USART2.bin](./misc/skr-mini/firmware-USART2.bin). Use TFT port USART2 to communicate with raspberry pi. Connect the UART-TX of raspberry pi with the USART-RX2 of motherboard and connect the UART-RX of raspberry pi with the USART-TX2 of motherboard directly to communicate normally.
|
|
|
|
Alternatively, find instructions on how to build the firmware yourself [here](https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#build-firmware-image).
|
|
|
|
### Flash Firmware
|
|
|
|
1. Rename `firmware-USB.bin` or `firmware-USART2.bin` to `firmware.bin`.
|
|
Important: If the file is not renamed, the bootloader will not be updated properly.
|
|
2. Copy `firmware.bin` to the root directory of the microSD card (make sure the card is in FAT32 format).
|
|
3. Power off the SKR-mini-E3-V3.0.
|
|
4. Insert the microSD card.
|
|
5. Power on the SKR-mini-E3-V3.0.
|
|
6. After a few seconds, the SKR-mini-E3-V3.0 should be flashed.
|
|
7. You can confirm that the flash was successful, by running ls /dev/serial/by-id. If the flash was successful, you'll see something like the following:
|
|
<img src="./misc/skr-mini/ls-output.png" alt='ls output'/>
|
|
|
|
### Download Klipper Configuration
|
|
|
|
1. Download [printer-skr-mini-e3-v3.cfg](./printer-skr-mini-e3-v3.cfg) and rename it to `printer.cfg`. This is the *only* `printer.cfg` that you will be using. Anytime there is a reference to `printer.cfg`, you will use this `printer.cfg` that you just saved/renamed.
|
|
2. Follow the instructions found in the [Download Klipper Configuration](https://github.com/bassamanator/Sovol-SV06-firmware#download-klipper-configuration) section and onwards. 💡 *Remember to use the `printer.cfg` that you saved in step 1*.
|
|
|
|
# Sources
|
|
|
|
- https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#how-to-use-klipper-on-skr-mini-e3-v30
|
|
- https://forum.sovol3d.com/t/sv06-mit-skr-e3-mini-v3/1189/24
|
|
- https://github.com/bassamanator/everything-sovol-sv06/discussions/14
|