Adjust, minor.

https://github.com/Sovol3d/Sv06-Source-Code/blob/main/Marlin/Configuration_adv.h#L2648-L2730

.vscode/settings.json

@@ -20,6 +20,7 @@
 		"Klipper",
 		"Klipperized",
 		"lrwxrwxrwx",
+		"microsteps",
 		"moonraker",
 		"normalsize",
 		"octahedroflake",

cfgs/misc-macros.cfg

@@ -29,9 +29,11 @@ gcode:
     SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=0
 
 [gcode_macro _globals]
+# NOTE 0 = false; 1 = true
 variable_filament_sensor_enabled: 1 # NOTE Enable(1) or disable(0) the filament sensor, if one is connected
 variable_beeping_enabled: 1 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
 variable_bed_temp_over: 10 # NOTE Start print if bed temperature is over by this amount, otherwise wait for temperature drop
+variable_bed_temp_not_exact: 1 # NOTE Start print if bed temperature is `target temperature - 1` but continue to heat until target is reached
 variable_kamp_enable: 0 # NOTE Enable(1) or disable(0) KAMP (adaptive mesh)
 variable_pre_purge_prime_length: 1.40
 gcode:
@@ -75,12 +77,20 @@ gcode:
 [gcode_macro M190]
 rename_existing: M99190
 gcode:
+    # Variables
+    {% set bedtempNotExact = printer["gcode_macro _globals"].bed_temp_not_exact|default(1)|int %}
+
     # Parameters
     {% set s = params.S|float %}
 
     M140 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %}   ; Set bed temp
     {% if s != 0 %}
-        TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s} MAXIMUM={s+1}  ; Wait for bed temp (within 1 degree)
+        {% if bedtempNotExact == 1 %}
+            TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s-1} MAXIMUM={s+1}  ; set & wait for bed temp (within -1 or +1 degree)
+            M140 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %} ; set & don't wait for bed temp
+        {% else %}
+            TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s} MAXIMUM={s+1}    ; Wait for bed temp (within +1 degree)
+        {% endif %}
     {% endif %}
 
 [gcode_macro PURGE_LINE]
@@ -189,12 +199,7 @@ gcode:
 
     M400                                    ; wait for buffer to clear
     G92 E0                                  ; zero the extruder
-    
-    {% if printer['pause_resume'].is_paused|int == 0 %}
-        CONDITIONAL_BEEP i=3 dur=300 freq=400
     G1 E-{PRE_PURGE_PRIME_LENGTH} F400      ; retract filament
-    {% endif %}
-    
     G91                                     ; relative positioning
 
     #   Set safe speeds

differences.md

@@ -0,0 +1,6 @@
+# Differences
+
+| Property                  | Marlin | OSS Klipper Config |
+| ------------------------- | ------ | ------------------ |
+| `stepper_z` `run_current` | 0.800  | 0.900              |
+| `microsteps`              | 16     | 128                |

printer.cfg

@@ -39,10 +39,10 @@ homing_retract_dist: 0
 
 [tmc2209 stepper_x]
 uart_pin: PC1
-run_current: 0.900
+run_current: 0.900 # 0.860 marlin & master
 stealthchop_threshold: 0
 interpolate: False
-sense_resistor: 0.150
+sense_resistor: 0.110 # 0.150
 uart_address: 3
 driver_SGTHRS: 81
 diag_pin: PA5
@@ -64,7 +64,7 @@ uart_pin: PC0
 run_current: 0.900
 stealthchop_threshold: 0
 interpolate: False
-sense_resistor: 0.150
+sense_resistor: 0.110 # 0.150
 uart_address: 3
 driver_SGTHRS: 81
 diag_pin: PA6
@@ -82,10 +82,10 @@ homing_speed: 5
 
 [tmc2209 stepper_z]
 uart_pin: PA15
-run_current: 0.900
+run_current: 0.800 # 0.900 prev personal # 0.800 marlin # 1.000 master
 stealthchop_threshold: 0
 interpolate: False
-sense_resistor: 0.150
+sense_resistor: 0.110 # 0.150
 uart_address: 3
 diag_pin: PA7
 
@@ -250,32 +250,13 @@ runout_gcode:
 #*# z_offset = 1.300
 #*#
 #*# [axis_twist_compensation]
-#*# z_compensations = 0.083802, -0.029167, -0.054635
+#*# z_compensations = 0.086615, -0.020885, -0.065729
 #*# compensation_start_x = 27.0
 #*# compensation_end_x = 195.0
 #*#
 #*# [bed_mesh default-1]
 #*# version = 1
 #*# points =
-#*# 	0.017700, 0.039838, 0.034162, 0.012223, -0.046875
-#*# 	-0.056675, -0.012819, 0.009631, -0.006839, -0.086094
-#*# 	-0.116831, -0.054850, -0.040056, -0.055433, -0.120625
-#*# 	-0.121362, -0.051100, -0.034588, -0.050745, -0.111094
-#*# 	-0.059643, 0.010619, 0.036506, 0.014255, -0.039375
-#*# min_x = 27.0
-#*# max_x = 222.0
-#*# min_y = 6.0
-#*# max_y = 203.0
-#*# x_count = 5
-#*# y_count = 5
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*#
-#*# [bed_mesh default-0]
-#*# version = 1
-#*# points =
 #*# 	0.038482, 0.061556, 0.047131, 0.009098, -0.055469
 #*# 	-0.033862, 0.002963, 0.008381, -0.014808, -0.099375
 #*# 	-0.095737, -0.047819, -0.040213, -0.062620, -0.132031
@@ -292,7 +273,7 @@ runout_gcode:
 #*# algo = lagrange
 #*# tension = 0.2
 #*#
-#*# [bed_mesh default]
+#*# [bed_mesh default-0]
 #*# version = 1
 #*# points =
 #*# 	0.037145, 0.055020, 0.034770, -0.006886, -0.072291
@@ -300,6 +281,25 @@ runout_gcode:
 #*# 	-0.095512, -0.047480, -0.047261, -0.073292, -0.135573
 #*# 	-0.091918, -0.042793, -0.043824, -0.073136, -0.132760
 #*# 	-0.026449, 0.032520, 0.031801, -0.001886, -0.079010
+#*# min_x = 27.0
+#*# max_x = 222.0
+#*# min_y = 6.0
+#*# max_y = 203.0
+#*# x_count = 5
+#*# y_count = 5
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = lagrange
+#*# tension = 0.2
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.029919, 0.051593, 0.042329, -0.005485, -0.076198
+#*# 	  -0.035550, 0.010968, 0.015923, -0.012203, -0.101979
+#*# 	  -0.095706, -0.038564, -0.032827, -0.059860, -0.134323
+#*# 	  -0.098988, -0.036220, -0.031733, -0.060641, -0.127292
+#*# 	  -0.035238, 0.039718, 0.042954, 0.004047, -0.067135
 #*# x_count = 5
 #*# y_count = 5
 #*# mesh_x_pps = 2