Merge branch 'kamp' into develop. Moved imports into osskc.cfg.

cfgs/CALIBRATION.cfg

@@ -46,4 +46,4 @@ gcode:
     TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=60
     TEMPERATURE_WAIT SENSOR=extruder MINIMUM=180
     G28
-    BED_MESH_CALIBRATE
+    _BED_MESH_CALIBRATE

cfgs/kamp/Adaptive_Meshing.cfg

@@ -0,0 +1,104 @@
+# # # Klipper Adaptive Meshing # # #
+
+# Heads up! If you have any other BED_MESH_CALIBRATE macros defined elsewhere in your config, you will need to comment out / remove them for this to work. (Klicky/Euclid Probe)
+# You will also need to be sure that [exclude_object] is defined in printer.cfg, and your slicer is labeling objects.
+# This macro will parse information from objects in your gcode to define a min and max mesh area to probe, creating an adaptive mesh!
+# This macro will not increase probe_count values in your [bed_mesh] config. If you want richer meshes, be sure to increase probe_count. We recommend at least 5,5.
+
+[gcode_macro BED_MESH_CALIBRATE]
+rename_existing: _BED_MESH_CALIBRATE
+gcode:
+
+    {% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}                                # Gather all object points
+    {% set bed_mesh_min = printer.configfile.settings.bed_mesh.mesh_min %}                                                          # Get bed mesh min from printer.cfg
+    {% set bed_mesh_max = printer.configfile.settings.bed_mesh.mesh_max %}                                                          # Get bed mesh max from printer.cfg
+    {% set probe_count = printer.configfile.settings.bed_mesh.probe_count %}                                                        # Get probe count from printer.cfg
+    {% set verbose_enable = printer["gcode_macro _KAMP_Settings"].verbose_enable | abs %}                                           # Pull verbose setting from _KAMP_Settings
+    {% set mesh_margin = printer["gcode_macro _KAMP_Settings"].mesh_margin | float %}                                               # Pull mesh margin setting from _KAMP_Settings
+    {% set fuzz_amount = printer["gcode_macro _KAMP_Settings"].fuzz_amount | float %}                                               # Pull fuzz amount setting from _KAMP_Settings
+    {% set probe_count = probe_count if probe_count|length > 1 else probe_count * 2  %}                                             # If probe count is only a single number, convert it to 2. E.g. probe_count:7 = 7,7
+    {% set max_probe_point_distance_x = ( bed_mesh_max[0] - bed_mesh_min[0] ) / (probe_count[0] - 1)  %}                            # Determine max probe point distance
+    {% set max_probe_point_distance_y = ( bed_mesh_max[1] - bed_mesh_min[1] ) / (probe_count[1] - 1)  %}                            # Determine max probe point distance
+    {% set x_min = all_points | map(attribute=0) | min | default(bed_mesh_min[0]) %}                                                # Set x_min from smallest object x point
+    {% set y_min = all_points | map(attribute=1) | min | default(bed_mesh_min[1]) %}                                                # Set y_min from smallest object y point
+    {% set x_max = all_points | map(attribute=0) | max | default(bed_mesh_max[0]) %}                                                # Set x_max from largest object x point
+    {% set y_max = all_points | map(attribute=1) | max | default(bed_mesh_max[1]) %}                                                # Set y_max from largest object y point
+
+    {% set fuzz_range = range((0) | int, (fuzz_amount * 100) | int + 1) %}                                                          # Set fuzz_range between 0 and fuzz_amount
+    {% set adapted_x_min = (bed_mesh_min[0] + fuzz_amount - mesh_margin, x_min) | max - (fuzz_range | random / 100.0) %}            # Adapt x_min to margin and fuzz constraints
+    {% set adapted_y_min = (bed_mesh_min[1] + fuzz_amount - mesh_margin, y_min) | max - (fuzz_range | random / 100.0) %}            # Adapt y_min to margin and fuzz constraints
+    {% set adapted_x_max = (bed_mesh_max[0] - fuzz_amount + mesh_margin, x_max) | min + (fuzz_range | random / 100.0) %}            # Adapt x_max to margin and fuzz constraints
+    {% set adapted_y_max = (bed_mesh_max[1] - fuzz_amount + mesh_margin, y_max) | min + (fuzz_range | random / 100.0) %}            # Adapt y_max to margin and fuzz constraints
+
+    {% set points_x = (((adapted_x_max - adapted_x_min) / max_probe_point_distance_x) | round(method='ceil') | int) + 1 %}          # Define probe_count's x point count and round up
+    {% set points_y = (((adapted_y_max - adapted_y_min) / max_probe_point_distance_y) | round(method='ceil') | int) + 1 %}          # Define probe_count's y point count and round up
+
+    {% if (([points_x, points_y]|max) > 6) %}                                                                                       # 
+        {% set algorithm = "bicubic" %}                                                                                             # 
+        {% set min_points = 4 %}                                                                                                    # 
+    {% else %}                                                                                                                      # Calculate if algorithm should be bicubic or lagrange
+        {% set algorithm = "lagrange" %}                                                                                            # 
+        {% set min_points = 3 %}                                                                                                    # 
+    {% endif %}                                                                                                                     # 
+
+    {% set points_x = [points_x, min_points]|max %}                                                                                 # Set probe_count's x points to fit the calculated algorithm
+    {% set points_y = [points_y, min_points]|max %}                                                                                 # Set probe_count's y points to fit the calculated algorithm
+    {% set points_x = [points_x, probe_count[0]]|min %}
+    {% set points_y = [points_y, probe_count[1]]|min %}
+
+    {% if verbose_enable == True %}                                                                                                 # If verbose is enabled, print information about KAMP's calculations
+
+        { action_respond_info( "Algorithm: {}.".format(                                                                              
+            (algorithm),                                                                                                            
+        )) }
+
+        { action_respond_info("Default probe count: {},{}.".format(                                                                  
+            (probe_count[0]),                                                                                                       
+            (probe_count[1]),                                                                                                       
+        )) }
+
+        { action_respond_info("Adapted probe count: {},{}.".format(                                                                  
+            (points_x),                                                                                                             
+            (points_y),                                                                                                             
+        )) }                                                                                                              
+
+        {action_respond_info("Default mesh bounds: {}, {}.".format(                                                                  
+            (bed_mesh_min[0],bed_mesh_min[1]),                                                                                      
+            (bed_mesh_max[0],bed_mesh_max[1]),                                                                                      
+        )) }
+
+        {% if mesh_margin > 0 %}                                                                                                    
+            {action_respond_info("Mesh margin is {}, mesh bounds extended by {}mm.".format(                                       
+                (mesh_margin),                                                                                                      
+                (mesh_margin),                                                                                       
+            )) }                                                                                                                    
+        {% else %}                                                                                                                  
+            {action_respond_info("Mesh margin is 0, margin not increased.")}                                                        
+        {% endif %}                                                                                                                 
+
+        {% if fuzz_amount > 0 %}                                                                                                    
+            {action_respond_info("Mesh point fuzzing enabled, points fuzzed up to {}mm.".format(                                     
+                (fuzz_amount),                                                                                                      
+            )) }                                                                                                                    
+        {% else %}                                                                                                                  
+            {action_respond_info("Fuzz amount is 0, mesh points not fuzzed.")}                                                      
+        {% endif %}                                                                                                                 
+
+        { action_respond_info("Adapted mesh bounds: {}, {}.".format(                                                                 
+            (adapted_x_min, adapted_y_min),                                                                                         
+            (adapted_x_max, adapted_y_max),                                                                                         
+        )) }
+
+        {action_respond_info("KAMP adjustments successful. Happy KAMPing!")}
+
+    {% endif %}
+
+    {% if probe_dock_enable == True %}
+        {attach_macro}                                                                                                              # Attach/deploy a probe if the probe is stored somewhere outside of the print area
+    {% endif %}
+
+    _BED_MESH_CALIBRATE mesh_min={adapted_x_min},{adapted_y_min} mesh_max={adapted_x_max},{adapted_y_max} ALGORITHM={algorithm} PROBE_COUNT={points_x},{points_y}
+
+    {% if probe_dock_enable == True %}
+        {detach_macro}                                                                                                              # Detach/stow a probe if the probe is stored somewhere outside of the print area
+    {% endif %}                                                                                                                     # End of verbose

cfgs/kamp/KAMP_Settings.cfg

@@ -0,0 +1,31 @@
+# Below you can include specific configuration files depending on what you want KAMP to do:
+
+[include ./Adaptive_Meshing.cfg]       # Include to enable adaptive meshing configuration.
+# [include ./KAMP/Line_Purge.cfg]             # Include to enable adaptive line purging configuration.
+
+[gcode_macro _KAMP_Settings]
+description: This macro contains all adjustable settings for KAMP 
+
+# The following variables are settings for KAMP as a whole.
+variable_verbose_enable: True               # Set to True to enable KAMP information output when running. This is useful for debugging.
+
+# The following variables are for adjusting adaptive mesh settings for KAMP.
+variable_mesh_margin: 0                     # Expands the mesh size in millimeters if desired. Leave at 0 to disable.
+variable_fuzz_amount: 0                     # Slightly randomizes mesh points to spread out wear from nozzle-based probes. Leave at 0 to disable.
+
+# The following variables are for those with a dockable probe like Klicky, Euclid, etc.                 # ----------------  Attach Macro | Detach Macro
+variable_probe_dock_enable: False           # Set to True to enable the usage of a dockable probe.      # ---------------------------------------------
+variable_attach_macro: 'Attach_Probe'       # The macro that is used to attach the probe.               # Klicky Probe:   'Attach_Probe' | 'Dock_Probe'
+variable_detach_macro: 'Dock_Probe'         # The macro that is used to store the probe.                # Euclid Probe:   'Deploy_Probe' | 'Stow_Probe'
+                                                                                                        # Legacy Gcode:   'M401'         | 'M402'
+
+# The following variables are for adjusting adaptive purge settings for KAMP.
+variable_purge_height: 0.8                  # Z position of nozzle during purge, default is 0.8.
+variable_tip_distance: 0                    # Distance between tip of filament and nozzle before purge. Should be similar to PRINT_END final retract amount.
+variable_purge_margin: 10                   # Distance the purge will be in front of the print area, default is 10.
+variable_purge_amount: 30                   # Amount of filament to be purged prior to printing.
+variable_flow_rate: 12                      # Flow rate of purge in mm3/s. Default is 12.
+
+gcode: # Gcode section left intentionally blank. Do not disturb.
+
+    {action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}

cfgs/kamp/Line_Purge.cfg

@@ -0,0 +1,113 @@
+[gcode_macro LINE_PURGE]
+description: A purge macro that adapts to be near your actual printed objects
+gcode:
+    # Get relevant printer params
+    {% set travel_speed = (printer.toolhead.max_velocity) * 60 | float %}
+    {% set cross_section = printer.configfile.settings.extruder.max_extrude_cross_section | float %}
+    
+    # Use firmware retraction if it is defined
+    {% if printer.firmware_retraction is defined %}
+        {% set RETRACT = G10 | string %}
+        {% set UNRETRACT = G11 | string %}
+    {% else %}
+        {% set RETRACT = 'G1 E-.5 F2100' | string %}
+        {% set UNRETRACT = 'G1 E.5 F2100' | string %}
+    {% endif %}
+
+    # Get purge settings from _Kamp_Settings
+    {% set verbose_enable = printer["gcode_macro _KAMP_Settings"].verbose_enable | abs %}
+    {% set purge_height = printer["gcode_macro _KAMP_Settings"].purge_height | float %}
+    {% set tip_distance = printer["gcode_macro _KAMP_Settings"].tip_distance | float %}
+    {% set purge_margin = printer["gcode_macro _KAMP_Settings"].purge_margin | float %}
+    {% set purge_amount = printer["gcode_macro _KAMP_Settings"].purge_amount | float %}
+    {% set flow_rate = printer["gcode_macro _KAMP_Settings"].flow_rate | float %}
+
+
+    # Calculate purge origins and centers from objects
+    {% set all_points = printer.exclude_object.objects | map(attribute='polygon') | sum(start=[]) %}    # Get all object points
+    {% set purge_x_min = (all_points | map(attribute=0) | min | default(0)) %}                          # Object x min
+    {% set purge_x_max = (all_points | map(attribute=0) | max | default(0)) %}                          # Object x max
+    {% set purge_y_min = (all_points | map(attribute=1) | min | default(0)) %}                          # Object y min
+    {% set purge_y_max = (all_points | map(attribute=1) | max | default(0)) %}                          # Object y max
+
+    {% set purge_x_center = ([((purge_x_max + purge_x_min) / 2) - (purge_amount / 2), 0] | max) %}      # Create center point of purge line relative to print on X axis
+    {% set purge_y_center = ([((purge_y_max + purge_y_min) / 2) - (purge_amount / 2), 0] | max) %}      # Create center point of purge line relative to print on Y axis
+
+    {% set purge_x_origin = ([purge_x_min - purge_margin, 0] | max) %}                                  # Add margin to x min, compare to 0, and choose the larger
+    {% set purge_y_origin = ([purge_y_min - purge_margin, 0] | max) %}                                  # Add margin to y min, compare to 0, and choose the larger
+
+    # Calculate purge speed
+    {% set purge_move_speed = (flow_rate / cross_section) * 60 | float %}
+
+    {% if cross_section != 5 %}
+
+        {action_respond_info("[Extruder] max_extrude_cross_section is not configured correctly, please set it to 5. Purge skipped.")}
+
+    {% else %}
+
+        {% if verbose_enable == True %}
+
+        {action_respond_info("Moving filament tip {}mms".format(                                                                 
+            (tip_distance),                                                                                      
+        )) }
+        {% endif %}
+
+        {% if printer.firmware_retraction is defined %}
+            {action_respond_info("KAMP purge is using firmware retraction.")}
+        {% else %}
+            {action_respond_info("KAMP purge is not using firmware retraction, it is recommended to configure it.")}
+        {% endif %}
+
+        {% if purge_y_origin > 0 %}
+        
+            {action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm/s3.".format(                                                                 
+                (purge_x_center),
+                (purge_y_origin),
+                (purge_amount),
+                (flow_rate),
+            )) }
+    
+        {% else %}
+    
+            {action_respond_info("KAMP purge starting at {}, {} and purging {}mm of filament, requested flow rate is {}mm/s3.".format(                                                                 
+                (purge_x_origin),
+                (purge_y_center),
+                (purge_amount),
+                (flow_rate),
+            )) }
+
+        {% endif %}
+
+        {% if purge_y_origin > 0 %}                                                             # If there's room on Y, purge along X axis in front of print area
+
+            G92 E0                                                                              # Reset extruder
+            G0 F{travel_speed}                                                                  # Set travel speed
+            G90                                                                                 # Absolute positioning
+            G0 X{purge_x_center} Y{purge_y_origin}                                              # Move to purge position
+            G0 Z{purge_height}                                                                  # Move to purge Z height
+            M83                                                                                 # Relative extrusion mode
+            G1 E{tip_distance} F{purge_move_speed}                                              # Move filament tip
+            G1 X{purge_x_center + purge_amount} E{purge_amount} F{purge_move_speed}             # Purge line
+            {RETRACT}                                                                           # Retract
+            G92 E0                                                                              # Reset extruder distance
+            M82                                                                                 # Absolute extrusion mode
+            G0 Z{purge_height * 2} F{travel_speed}                                              # Z hop
+
+        {% else %}                                                                              # If there's room on X, purge along Y axis to the left of print area
+            
+            G92 E0                                                                              # Reset extruder
+            G0 F{travel_speed}                                                                  # Set travel speed
+            G90                                                                                 # Absolute positioning
+            G0 X{purge_x_origin} Y{purge_y_center}                                              # Move to purge position
+            G0 Z{purge_height}                                                                  # Move to purge Z height
+            M83                                                                                 # Relative extrusion mode
+            G1 E{tip_distance} F{purge_move_speed}                                              # Move filament tip
+            G1 Y{purge_y_center + purge_amount} E{purge_amount} F{purge_move_speed}             # Purge line
+            {RETRACT}                                                                           # Retract
+            G92 E0                                                                              # Reset extruder distance
+            M82                                                                                 # Absolute extrusion mode
+            G0 Z{purge_height * 2} F{travel_speed}                                              # Z hop
+
+        {% endif %}
+    
+    {% endif %}

cfgs/misc-macros.cfg

@@ -29,13 +29,10 @@ gcode:
 variable_filament_sensor_enabled: 0 # NOTE Enable(1) or disable(0) the filament sensor, if one is connected
 variable_beeping_enabled: 1 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
 variable_bed_temp_over: 10 # NOTE Start print if bed temperature is over by this amount, otherwise wait for temperature drop
+variable_kamp_enable: 1 # NOTE Enable(1) or disable(0) KAMP (adaptive mesh)
 variable_pre_purge_prime_length: 1.40
 gcode:
-    # DELETEME This section is unnecessary
-    SET_GCODE_VARIABLE MACRO=_globals VARIABLE=pre_purge_prime_length VALUE={ variable_pre_purge_prime_length }
-    SET_GCODE_VARIABLE MACRO=_globals VARIABLE=filament_sensor_enabled VALUE={ variable_filament_sensor_enabled }
-    SET_GCODE_VARIABLE MACRO=_globals VARIABLE=beeping_enabled VALUE={ variable_beeping_enabled }
-    SET_GCODE_VARIABLE MACRO=_globals VARIABLE=bed_temp_over VALUE={ variable_bed_temp_over }
+    # Don't delete this section
 
 [gcode_macro CONDITIONAL_BEEP]
 gcode:
@@ -122,6 +119,7 @@ gcode:
 
 [gcode_macro PRINT_START]
 gcode:
+    ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
     # Parameters
     {% set bedtemp = params.BED|int %}
     {% set hotendtemp = params.HOTEND|int %}
@@ -132,6 +130,7 @@ gcode:
     {% set bedtempOver = printer["gcode_macro _globals"].bed_temp_over|default(0)|int %}
     {% set maxVelocity = printer.configfile.settings.printer.max_velocity|default(200)|int %}
     {% set maxVelocityAdjusted =  (0.90 * maxVelocity * 60)|int %}
+    {% set kampEnabled=printer["gcode_macro _globals"].kamp_enable|default(0)|int %}
 
     {% if printer.configfile.settings.safe_z_home %}
         {% set startX = printer.configfile.settings.safe_z_home.home_xy_position[0]|float %}
@@ -149,9 +148,6 @@ gcode:
         {% endif %}
     {% endif %}
 
-    BED_MESH_PROFILE LOAD=default                        ; NOTE if not using a mesh, comment out this line
-    ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
-
     G90                                                  ; absolute positioning
     M140 S{bedtempAlmost}                                ; set & don't wait for bed temp
     M104 S{hotendtempStepOne}                            ; set & don't wait for hotend temp
@@ -161,12 +157,21 @@ gcode:
     {% endif %}
 
     M190 S{bedtempAlmost}                                ; set & wait for bed temp
+    {% if kampEnabled == 0 %}
         M104 S{hotendtempStepTwo}                            ; set & don't wait for hotend temp
+    {% endif %}
     M190 S{bedtemp}                                      ; set & wait for bed temp
     M140 S{bedtempSlicer}                                ; set & don't wait for bed temp ; set temp to sliced setting regardless
 
+    {% if kampEnabled == 0 %}
+        BED_MESH_PROFILE LOAD=default                        ; NOTE if not using a mesh, comment out this line
         M104 S{hotendtemp}                                   ; set & don't wait for hotend temp
         G28 Z                                                ; final z homing
+    {% else %}
+        G28 Z                                                ; final z homing
+        BED_MESH_CALIBRATE                                   ; KAMP mesh
+        M104 S{hotendtemp}                                   ; set & don't wait for hotend temp
+    {% endif %}
 
     G1 X0 Y0 F{maxVelocityAdjusted}
     M109 S{hotendtemp}                                   ; set & wait for hotend temp

osskc.cfg

@@ -0,0 +1,10 @@
+[include ./cfgs/misc-macros.cfg]
+[include ./cfgs/PARKING.cfg]
+[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
+[include ./cfgs/CALIBRATION.cfg]
+[include ./cfgs/kamp/KAMP_Settings.cfg]
+
+# NOTE Uncomment the ONE of the following lines if you're using an adxl345
+# [include ./cfgs/adxl-rp2040.cfg]
+# [include ./cfgs/adxl-rpi-pico-2x.cfg]
+# [include ./cfgs/adxl-direct.cfg]

printer.cfg

@@ -4,15 +4,7 @@
 # 
 # See https://www.klipper3d.org/Config_Reference.html for configuration reference.
 
-[include ./cfgs/misc-macros.cfg]
-[include ./cfgs/PARKING.cfg]
-[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
-[include ./cfgs/CALIBRATION.cfg]
-
-# NOTE Uncomment the ONE of the following lines if you're using an adxl345
-# [include ./cfgs/adxl-rp2040.cfg]
-# [include ./cfgs/adxl-rpi-pico-2x.cfg]
-# [include ./cfgs/adxl-direct.cfg]
+[include ./osskc.cfg]
 
 [mcu]
 # NOTE Obtain definition by "ls -l /dev/serial/by-path/" or "ls -l /dev/serial/by-id/"