Bassam Husain
21994e3829
Add idle_timeout section.
2024-02-22 17:25:27 -05:00
Bassam Husain
c9a469d677
Merge branch 'develop', KAMP code. Restructured osskc code.
2023-07-28 02:43:12 -04:00
Bassam Husain
67307f5679
Adjust misc-macros.cfg, minor.
2023-07-01 02:44:47 -04:00
Bassam Husain
d6f03f7a2c
Cleanup in misc-macros.cfg. Adjusted calibration.cfg to work dynamically.
2023-07-01 00:51:59 -04:00
Bassam Husain
5ada85f964
Bed temp over now customizable.
2023-06-09 17:28:07 -04:00
Bassam Husain
24a4262af2
Pulled in print_start from personal: prints start with higher bed temp now, range 10C.
2023-05-20 19:59:18 -04:00
Björn Marschollek
835e990d88
Avoid cooling down the extruder in PRINT_START
...
The current `PRINT_START` macro heats the extruder to 150 degrees, then
to 170, and finally to the target temperature. If the extruder is
already hot, this unnecessarily cools it down and wastes time.
This change only cools down the hotend if it's above the target
temperature and then only to that temperature.
If the extruder was colder than 150 degrees, this change maintains the
current behaviour.
2023-04-22 12:20:01 +02:00
Bassam Husain
23d24aab17
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-20 17:09:58 -04:00
Björn Marschollek
4a38d34a0e
Add a minimum bed temperature of 0 degrees
...
If the bed temperature is less than 2, the print job fails with an
error message complaining about an invalid temperature. This happens,
for instance, when printing ABS where the bed is not supposed to be
heated.
This change makes sure that the bed temperature cannot be negative.
2023-04-20 22:53:19 +02:00
Bassam Husain
5e342261c8
Pulling in print_start from personal branch.
2023-04-20 12:19:06 -04:00
Bassam Husain
807c91507a
Pulling in from personal branch.
2023-04-17 00:41:03 -04:00
Bassam Husain
a30d367d1d
Commented out raspberry pi temperature section.
2023-04-17 00:21:03 -04:00
Bassam Husain
5abaf73b9c
Comment cleanup in print_end.
2023-04-13 17:32:44 -04:00
Bassam Husain
238091d860
Minor speedup in print_start.
2023-04-13 17:28:55 -04:00
Bassam Husain
6dc119cf99
Added pause/runout/m600 to faq. Reduced speed in print_start.
2023-04-07 19:44:30 -04:00
Bassam Husain
953daefa32
Adjusted PRINT_START sequence to save time, and to prevent oozing. Increased microsteps to 128, and added square_corner_velocity.
2023-04-07 09:52:06 -04:00
Bassam Husain
8346c79f35
Adjusted start position for purge_line.
2023-04-02 19:00:47 -04:00
Bassam Husain
98a1cd7fe6
Purge_line macro adjusted to print at the front of the bed; printer agnostic. Print_end adjusted to use safer speed.
2023-04-02 18:31:58 -04:00
Bassam Husain
3551f307ae
Added beeping on colour/filament change.
2023-03-20 01:04:36 -04:00
Bassam Husain
95897311e6
Filament runout sensor code merged.
2023-03-14 21:08:16 -04:00
Bassam Husain
c2bd1fa076
More changes pulled from personal. Added filament sensor pinout.
2023-03-14 19:47:16 -04:00
Bassam Husain
9239a54e8b
More changes pulled from personal.
2023-03-14 18:55:07 -04:00
Bassam Husain
c967be1023
More changes pulled from personal.
2023-03-14 18:45:30 -04:00
Bassam Husain
64a6f98fe4
Pulling in structure from personal branch.
2023-03-14 18:36:53 -04:00
Bassam Husain
150e1b7425
Removed CHECK_PRE_PURGE_PRIME_LENGTH
...
macro.
2023-03-12 14:35:13 -04:00
Bassam Husain
0b5909ab53
Added ADJUST_FILAMENT_SENSOR_STATUS use back.
2023-03-12 12:19:59 -04:00
Bassam Husain
c0f4eb76fc
Merge branch 'fix-sensor' into personal
2023-03-12 11:37:09 -04:00
Bassam Husain
36ba332e81
Added SET_FILAMENT_SENSOR to print_start.
2023-03-12 11:15:01 -04:00
Bassam Husain
f70f23e290
ADJUST_FILAMENT_SENSOR_STATUS and conditional_beep fixed.
2023-03-12 10:44:23 -04:00
Bassam Husain
5ccabd1a3d
Added conditional beeping.
2023-03-12 01:53:44 -05:00
Bassam Husain
69a5cbc45c
Merging filament sensor related code.
2023-03-12 01:32:40 -05:00
Bassam Husain
e3762db8b2
Minor cleanup in misc-macros.cfg.
2023-03-10 07:59:26 -05:00
Bassam Husain
6c63082072
Moved many sections from printer.cfg to misc-macros.cfg.
2023-03-10 04:52:04 -05:00
Bassam Husain
6492c67e31
Renamed macros.cfg to misc-macros.cfg.
2023-03-10 04:46:19 -05:00
