Bassam Husain
940ea48541
Update README.md
2023-04-22 15:00:45 -04:00
Bassam Husain
57e6755ced
Merge pull request #42 from muffix/dont-cool-down-in-print-start
...
Avoid cooling down the extruder in PRINT_START
2023-04-22 07:24:44 -04:00
Björn Marschollek
835e990d88
Avoid cooling down the extruder in PRINT_START
...
The current `PRINT_START` macro heats the extruder to 150 degrees, then
to 170, and finally to the target temperature. If the extruder is
already hot, this unnecessarily cools it down and wastes time.
This change only cools down the hotend if it's above the target
temperature and then only to that temperature.
If the extruder was colder than 150 degrees, this change maintains the
current behaviour.
2023-04-22 12:20:01 +02:00
Bassam Husain
45434cde14
Merge pull request #41 from muffix/add-rpi2040-with-2x-adxl345
...
Add config for 2 ADXL345 via RasPi pico
2023-04-21 16:41:58 -04:00
Bassam Husain
51fd3f0b19
Update adxl-rpi-pico-2x.cfg
...
Minor adjustments to adxl-rpi-pico-2x.cfg.
2023-04-21 16:41:26 -04:00
Björn Marschollek
4df5ef2db3
Add config for 2 ADXL345 via RasPi pico
...
This adds a configuration supporting two ADXL345 sensors at the same
time though a Raspberry Pi pico.
Resonance measurements for both the head and the bed can be done without
having to change the sensors.
2023-04-21 20:26:11 +02:00
Bassam Husain
23d24aab17
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-20 17:09:58 -04:00
Bassam Husain
43d067acab
Merge pull request #39 from muffix/add-minimum-for-bed-temperature
...
Add a minimum bed temperature of 0 degrees in `PRINT_START`.
2023-04-20 17:04:35 -04:00
Björn Marschollek
4a38d34a0e
Add a minimum bed temperature of 0 degrees
...
If the bed temperature is less than 2, the print job fails with an
error message complaining about an invalid temperature. This happens,
for instance, when printing ABS where the bed is not supposed to be
heated.
This change makes sure that the bed temperature cannot be negative.
2023-04-20 22:53:19 +02:00
Bassam Husain
5e342261c8
Pulling in print_start from personal branch.
2023-04-20 12:19:06 -04:00
Bassam Husain
1823d0ca37
Updated readme: Download section.
2023-04-19 22:59:32 -04:00
Bassam Husain
8bfed9c573
Spelling fixes.
2023-04-18 07:44:09 -04:00
Bassam Husain
807c91507a
Pulling in from personal branch.
2023-04-17 00:41:03 -04:00
Bassam Husain
a30d367d1d
Commented out raspberry pi temperature section.
2023-04-17 00:21:03 -04:00
Bassam Husain
5abaf73b9c
Comment cleanup in print_end.
2023-04-13 17:32:44 -04:00
Bassam Husain
238091d860
Minor speedup in print_start.
2023-04-13 17:28:55 -04:00
Bassam Husain
6dc119cf99
Added pause/runout/m600 to faq. Reduced speed in print_start.
2023-04-07 19:44:30 -04:00
Bassam Husain
9e68610908
Update README.md
2023-04-07 18:07:24 -04:00
Bassam Husain
b3040f4244
Create CODE_OF_CONDUCT.md
2023-04-07 14:04:00 -04:00
Bassam Husain
8c6ebbca2c
Create CONTRIBUTING.md
2023-04-07 13:56:28 -04:00
Bassam Husain
1f3707123a
Update issue templates
2023-04-07 13:47:17 -04:00
Bassam Husain
953daefa32
Adjusted PRINT_START sequence to save time, and to prevent oozing. Increased microsteps to 128, and added square_corner_velocity.
2023-04-07 09:52:06 -04:00
Bassam Husain
d0b426d5b0
Updated readme.
2023-04-06 06:44:26 -04:00
Bassam Husain
4b90c7abc5
Added G90 to steps after homing.
2023-04-06 06:22:01 -04:00
Bassam Husain
daa07e37c0
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware.
2023-04-03 14:49:03 -04:00
Bassam Husain
758a3f8b77
Update README.md
...
Added instructions for adjusting slicer start/end gcode.
2023-04-03 12:51:49 -04:00
Bassam Husain
c1427d9418
Update README.md
2023-04-03 08:28:35 -04:00
Bassam Husain
371e0d604a
Update README.md
2023-04-03 08:09:36 -04:00
Bassam Husain
5b5ce8df57
Adjusted readme.
2023-04-02 19:11:43 -04:00
Bassam Husain
8346c79f35
Adjusted start position for purge_line.
2023-04-02 19:00:47 -04:00
Bassam Husain
98a1cd7fe6
Purge_line macro adjusted to print at the front of the bed; printer agnostic. Print_end adjusted to use safer speed.
2023-04-02 18:31:58 -04:00
Bassam Husain
39131e0d66
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-02 11:08:47 -04:00
Bassam Husain
862c45b88f
Update README.md
...
Added firmware location to Flash Firmware section.
2023-04-01 22:48:49 -04:00
Bassam Husain
73f15169b6
README: minor change.
2023-03-27 18:33:48 -04:00
Bassam Husain
38cabc7513
Update README.md
...
Before you begin section.
2023-03-24 20:36:06 -04:00
Bassam Husain
d628b6e9ef
Updated 'before you begin' section to let users know that is assumed to be the username.
2023-03-23 12:05:36 -04:00
Bassam Husain
1e80ff171a
Updated m503 output.
2023-03-22 14:49:57 -04:00
Bassam Husain
37be3998d8
Updated flash firmware section. Added marlin.bin and updated klipper.bin to latest.
2023-03-22 14:43:39 -04:00
Bassam Husain
1e13d86eca
Updated FAQ to include SuperSlicer related questions.
2023-03-21 02:34:54 -04:00
Bassam Husain
7571e95a5a
Updated FAQ.
2023-03-20 01:12:05 -04:00
Bassam Husain
3551f307ae
Added beeping on colour/filament change.
2023-03-20 01:04:36 -04:00
Bassam Husain
140ff8cb30
Added KAMP to to-do list.
2023-03-16 15:55:18 -04:00
Bassam Husain
903cd16287
Minor change at the top.
2023-03-15 02:13:29 -04:00
Bassam Husain
eaea54e330
Added some fun gifs.
2023-03-15 02:03:27 -04:00
Bassam Husain
77468d319f
Edited Sources section.
2023-03-14 23:51:14 -04:00
Bassam Husain
fdfdcd6bb5
Updated FAQ section.
2023-03-14 21:12:30 -04:00
Bassam Husain
95897311e6
Filament runout sensor code merged.
2023-03-14 21:08:16 -04:00
Bassam Husain
0db62e01f3
Added FAQ section.
2023-03-14 20:22:40 -04:00
Bassam Husain
c2bd1fa076
More changes pulled from personal. Added filament sensor pinout.
2023-03-14 19:47:16 -04:00
Bassam Husain
545817dffc
SuperSlicer config bundle updated.
2023-03-14 19:26:01 -04:00
