Bassam Husain
82a5603d1e
Directory structure updated.
2023-05-12 00:57:51 -04:00
Bassam Husain
ad4c893fbc
Moved images to correct folder.
2023-05-12 00:53:25 -04:00
Bassam Husain
a5a75f3c1e
Added sv06-plus build plate model, removed sv06 build plate.
2023-05-10 21:35:55 -04:00
Bassam Husain
24610b1dee
Merge branch 'bed-temp' into personal
2023-05-10 18:50:02 -04:00
Bassam Husain
9d08c418c0
Print_start adjusted: comments styling only.
2023-05-10 18:49:04 -04:00
Bassam Husain
7112c53ad8
Print_start adjusted: prints will start as long as current bed temp is not higher than 10C compared to sliced bed temp.
2023-05-10 01:43:37 -04:00
Bassam Husain
f0602b5cb2
Print_start adjusted: added back 0 bed temp possibility.
2023-05-10 01:23:35 -04:00
Bassam Husain
5242dc7276
Print_start adjusted: prints should now start even if bed temp is higher than what was set in slicer; does set sliced temp at the end though.
2023-05-10 01:11:58 -04:00
Bassam Husain
05dba3939e
Adjusted PRINT_START bedtempAlmost logic.
2023-05-09 17:20:30 -04:00
Bassam Husain
d0c43f3777
Deleted SV06 marlin firmware.
2023-05-07 18:54:01 -04:00
Bassam Husain
4dcd5e3840
Adjusted mcu section.
2023-05-03 15:26:28 -04:00
Bassam Husain
53f6f75c85
Merge branch 'master' into sv06-plus
2023-05-03 15:25:35 -04:00
Bassam Husain
d062ee5bcc
Adjusted initial steps on how to find the mcu.
2023-05-03 15:23:19 -04:00
Bassam Husain
aa8d3de2c7
Merge branch 'master' into sv06-plus
2023-04-23 09:43:49 -04:00
Bassam Husain
b0d122a1c1
Adjust Initial steps, step 1.
2023-04-23 09:39:20 -04:00
Bassam Husain
6ede727449
Update README.md
...
Flash Firmware section.
2023-04-23 08:57:17 -04:00
Bassam Husain
f4f0fd50bb
Merge branch 'master' into sv06-plus
2023-04-22 16:59:00 -04:00
Bassam Husain
6eedc4bd60
Update README.md
...
Edit Adjust Your Slicer section.
2023-04-22 16:53:46 -04:00
Bassam Husain
3a85c0e532
Pulling in print_start from master branch.
2023-04-22 15:03:30 -04:00
Bassam Husain
940ea48541
Update README.md
2023-04-22 15:00:45 -04:00
Bassam Husain
9f69a7d355
Update README.md
2023-04-22 14:58:51 -04:00
Bassam Husain
57e6755ced
Merge pull request #42 from muffix/dont-cool-down-in-print-start
...
Avoid cooling down the extruder in PRINT_START
2023-04-22 07:24:44 -04:00
Bassam Husain
1cdcb4934b
PRINT_START adjust: don't cooldown if not necessary.
2023-04-22 07:10:06 -04:00
Björn Marschollek
835e990d88
Avoid cooling down the extruder in PRINT_START
...
The current `PRINT_START` macro heats the extruder to 150 degrees, then
to 170, and finally to the target temperature. If the extruder is
already hot, this unnecessarily cools it down and wastes time.
This change only cools down the hotend if it's above the target
temperature and then only to that temperature.
If the extruder was colder than 150 degrees, this change maintains the
current behaviour.
2023-04-22 12:20:01 +02:00
Bassam Husain
45434cde14
Merge pull request #41 from muffix/add-rpi2040-with-2x-adxl345
...
Add config for 2 ADXL345 via RasPi pico
2023-04-21 16:41:58 -04:00
Bassam Husain
51fd3f0b19
Update adxl-rpi-pico-2x.cfg
...
Minor adjustments to adxl-rpi-pico-2x.cfg.
2023-04-21 16:41:26 -04:00
Björn Marschollek
4df5ef2db3
Add config for 2 ADXL345 via RasPi pico
...
This adds a configuration supporting two ADXL345 sensors at the same
time though a Raspberry Pi pico.
Resonance measurements for both the head and the bed can be done without
having to change the sensors.
2023-04-21 20:26:11 +02:00
Bassam Husain
23d24aab17
Merge branch 'master' of github.com:bassamanator/Sovol-SV06-firmware
2023-04-20 17:09:58 -04:00
Bassam Husain
43d067acab
Merge pull request #39 from muffix/add-minimum-for-bed-temperature
...
Add a minimum bed temperature of 0 degrees in `PRINT_START`.
2023-04-20 17:04:35 -04:00
Bassam Husain
498e0d4a4d
PRINT_START bedtemp fix, 2nd try.
2023-04-20 16:56:25 -04:00
Björn Marschollek
4a38d34a0e
Add a minimum bed temperature of 0 degrees
...
If the bed temperature is less than 2, the print job fails with an
error message complaining about an invalid temperature. This happens,
for instance, when printing ABS where the bed is not supposed to be
heated.
This change makes sure that the bed temperature cannot be negative.
2023-04-20 22:53:19 +02:00
Bassam Husain
9b712df594
PRINT_START bedtemp fix.
2023-04-20 16:43:43 -04:00
Bassam Husain
e888ac0882
Added orange pi temp section.
2023-04-20 12:37:03 -04:00
Bassam Husain
323e8df221
Merge branch 'master' into sv06-plus: update download section.
2023-04-20 12:30:07 -04:00
Bassam Husain
40534f3788
Pulling in print_start from master branch.
2023-04-20 12:22:52 -04:00
Bassam Husain
5e342261c8
Pulling in print_start from personal branch.
2023-04-20 12:19:06 -04:00
Bassam Husain
89fbb10154
variable_pre_purge_prime_length reverted.
2023-04-20 12:10:00 -04:00
Bassam Husain
1823d0ca37
Updated readme: Download section.
2023-04-19 22:59:32 -04:00
Bassam Husain
6eb152e58d
Adjust PRINT_START: safe_z_home startX, startY.
2023-04-19 10:53:08 -04:00
Bassam Husain
c1672c9a42
Fixed sense_resistor according to specs.
2023-04-19 07:47:24 -04:00
Bassam Husain
2e5764f295
Adjusted print_start start x, y positions conditionally.
2023-04-18 10:39:22 -04:00
Bassam Husain
581ff9da48
Adjusted SS config bundle for Plus. Spelling fix.
2023-04-18 07:56:34 -04:00
Bassam Husain
4ecb37cf9f
Pulling from master.
2023-04-18 07:50:15 -04:00
Bassam Husain
8bfed9c573
Spelling fixes.
2023-04-18 07:44:09 -04:00
Bassam Husain
7e5aeb6654
Print_start adjusted.
2023-04-17 02:13:19 -04:00
Bassam Husain
f5d3499da7
Getting safe_z_home info in print_start.
2023-04-17 01:02:20 -04:00
Bassam Husain
2c8a4e5aa0
Print_start improvements.
2023-04-17 00:55:51 -04:00
Bassam Husain
b051707f52
Print_start improvements.
2023-04-17 00:42:57 -04:00
Bassam Husain
807c91507a
Pulling in from personal branch.
2023-04-17 00:41:03 -04:00
Bassam Husain
a30d367d1d
Commented out raspberry pi temperature section.
2023-04-17 00:21:03 -04:00
