PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-08 13:31:16 +00:00
Code Issues Packages Projects Releases Wiki Activity

Adjust before you begin section.

Browse Source
This commit is contained in:
Bassam Husain
2024-08-28 23:50:38 -04:00
parent 6b156cb9ae
commit f174110561
2 changed files with 12 additions and 4 deletions
Download Patch File Download Diff File Expand all files Collapse all files

1
.vscode/settings.json vendored
View File

@@ -31,6 +31,7 @@
"PARKFRONTLOW",
"PARKREAR",
"pico",
"Printables",
"Prusa",
"runout",
"Sovol",

15
README.md
View File

@@ -77,10 +77,8 @@ In many ways, this entire repository can be considered _my opinion_ on the `3D p
## Before You Begin
- This entire page is a **9 minute read**. Save yourself _hours of troubleshooting_ and read this documentation fully.
- ⚠️ Make sure your printer is in good physical condition, because print and travel speeds will be _a lot faster_. Beginners would be wise to run through [these steps](https://github.com/bassamanator/everything-sovol-sv06/blob/main/initialsteps.md).
- ⚠️ [Disable](https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#disable-usb-cable-5v-pin) the USB cable's 5V pin.
- Follow the steps in order. If an error was reported at a step, do no proceed to the next step.
- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via a data USB cable. 💡 Most of the micro USB cables that you find at home are _unlikely_ to be data cables, and it is not possible to tell just by looking.
- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via a _data_ USB cable.
- It is also assumed that the username on the host device is `pi`. If that is not the case, edit `moonraker.conf` and `cfgs/misc-macros.cfg` to change any mentions of `/home/pi` to `/home/yourUserName`.
- Klipper _must_ be installed on the host beforehand. Easiest is to use [MainsailOS](https://github.com/mainsail-crew/mainsail/releases/latest). [KIAUH](https://github.com/th33xitus/kiauh) is another option.
- Klipper _must_ be up to date.
@@ -90,7 +88,16 @@ In many ways, this entire repository can be considered _my opinion_ on the `3D p
- It is assumed that there is one instance of Klipper installed. If that is not the case, the steps in this guide will not work _perfectly_ for you.
- Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section.
- I would recommend searching for the word `NOTE` in this configuration. There are roughly half a dozen short points amongst the various files that you should be aware of.
<!-- - Link to recommended parts. -->
- Consider [these](https://github.com/bassamanator/everything-sovol-sv06/blob/main/parts/README.md#printed-upgrades) printable parts, and also see my [Printables](https://www.printables.com/@bassamanator) page.
> [!TIP]
> Most of the micro USB cables that you find at home are _unlikely_ to be data cables, and it is not possible to tell just by looking.
> [!CAUTION]
> Make sure your printer is in good physical condition, because print and travel speeds will be _a lot faster_. Beginners would be wise to run through [these steps](https://github.com/bassamanator/everything-sovol-sv06/blob/main/initialsteps.md).
> [!CAUTION]
> [Disable](https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#disable-usb-cable-5v-pin) the USB cable's 5V pin.
[🔼 Back to top](#outline)