PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-08 21:41:15 +00:00
Code Issues Packages Projects Releases Wiki Activity

Adjusted configure your printer section.

Browse Source
This commit is contained in:
Bassam Husain
2023-07-01 01:58:25 -04:00
parent f65c0e6e7f
commit b9a67cf09b
1 changed files with 15 additions and 26 deletions
Download Patch File Download Diff File Expand all files Collapse all files

41
README.md
View File

@@ -175,37 +175,26 @@ If you've done everything correctly, you should see no errors or warnings in you
You will be pasting/typing these commands into the Mainsail/Fluidd console.
1. `G28`
1. Check to see if `X` and `Y` max positions (`G90`, `G1 X223 F3000`, `G1 Y223 F3000`) can be reached, and adjust `position_max`, if necessary. You can probably go all the way up to `225` for `X` and `Y` both, however, I would not recommend it.
2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. You will hear a succession of beeps.
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam. The range is 250 to 261 from what I've seen, could be even higher for you. Adjust `position_max`, if necessary. I can go all the way to 258, however, I would not print anything higher than 257.
3. PID tune the bed, but first move the printhead to the center. Ideally, all PID tuning should occur at the temperatures that you print most at.
1. Check to see if `X` and `Y` max positions can be reached, and adjust `position_max`, if necessary. You might be able to go further, which is great, but I recommend leaving a 2mm gap for safety.
1. `G28`
2. `G90`
3. `G1 X111 Y111 Z40 F6000`
4. `PID_CALIBRATE HEATER=heater_bed TARGET=70`
5. `SAVE_CONFIG` (once completed)
3. `G1 X223 F3000`
4. `G1 Y223 F3000`
2. Do a mechanical gantry calibration; `G34`. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. You will hear a succession of beeps.
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam, and adjust `position_max`, if necessary.
3. PID tune the bed. Ideally, all PID tuning should occur at the temperatures that you print most at.
1. `PID_TEST_BED`
2. `SAVE_CONFIG` (once completed)
4. PID tune the extruder while part cooling fan runs at 25%.
1. `G28`
2. `G90`
3. `G1 X111 Y111 Z10 F6000`
4. `M106 S64`
5. `PID_CALIBRATE HEATER=extruder TARGET=245`
6. `SAVE_CONFIG` (once completed)
1. `PID_TEST_HOTEND`
2. `SAVE_CONFIG` (once completed)
5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test).
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`
3. Proceed to next steps after both temperatures have been reached.
4. `G28`
5. `PROBE_CALIBRATE`
6. `SAVE_CONFIG` (once completed)
1. `DO_PROBE_CALIBRATE`
2. Follow `z_offset` setup in Mainsail/Fluidd.
3. `SAVE_CONFIG` (once completed)
6. Create a bed mesh.
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`
3. Proceed to next steps after both temperatures have been reached.
4. `G28`
5. `BED_MESH_CALIBRATE`
6. `SAVE_CONFIG` (once completed)
1. `DO_CREATE_MESH`
2. `SAVE_CONFIG` (once completed)
If you've made it here, then your printer has been Klipperized, and is ready to print!