From b9a67cf09b6c1692e9afba2bd4d4a0082da5155e Mon Sep 17 00:00:00 2001 From: Bassam Husain Date: Sat, 1 Jul 2023 01:58:25 -0400 Subject: [PATCH] Adjusted configure your printer section. --- README.md | 41 +++++++++++++++-------------------------- 1 file changed, 15 insertions(+), 26 deletions(-) diff --git a/README.md b/README.md index c01e293..ee2e36d 100644 --- a/README.md +++ b/README.md @@ -175,37 +175,26 @@ If you've done everything correctly, you should see no errors or warnings in you You will be pasting/typing these commands into the Mainsail/Fluidd console. -1. `G28` - 1. Check to see if `X` and `Y` max positions (`G90`, `G1 X223 F3000`, `G1 Y223 F3000`) can be reached, and adjust `position_max`, if necessary. You can probably go all the way up to `225` for `X` and `Y` both, however, I would not recommend it. -2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. You will hear a succession of beeps. - 1. Figure out your `Z` `position_max` by baby stepping your way up to the beam. The range is 250 to 261 from what I've seen, could be even higher for you. Adjust `position_max`, if necessary. I can go all the way to 258, however, I would not print anything higher than 257. -3. PID tune the bed, but first move the printhead to the center. Ideally, all PID tuning should occur at the temperatures that you print most at. +1. Check to see if `X` and `Y` max positions can be reached, and adjust `position_max`, if necessary. You might be able to go further, which is great, but I recommend leaving a 2mm gap for safety. 1. `G28` 2. `G90` - 3. `G1 X111 Y111 Z40 F6000` - 4. `PID_CALIBRATE HEATER=heater_bed TARGET=70` - 5. `SAVE_CONFIG` (once completed) + 3. `G1 X223 F3000` + 4. `G1 Y223 F3000` +2. Do a mechanical gantry calibration; `G34`. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. You will hear a succession of beeps. + 1. Figure out your `Z` `position_max` by baby stepping your way up to the beam, and adjust `position_max`, if necessary. +3. PID tune the bed. Ideally, all PID tuning should occur at the temperatures that you print most at. + 1. `PID_TEST_BED` + 2. `SAVE_CONFIG` (once completed) 4. PID tune the extruder while part cooling fan runs at 25%. - 1. `G28` - 2. `G90` - 3. `G1 X111 Y111 Z10 F6000` - 4. `M106 S64` - 5. `PID_CALIBRATE HEATER=extruder TARGET=245` - 6. `SAVE_CONFIG` (once completed) + 1. `PID_TEST_HOTEND` + 2. `SAVE_CONFIG` (once completed) 5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test). - 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` - 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` - 3. Proceed to next steps after both temperatures have been reached. - 4. `G28` - 5. `PROBE_CALIBRATE` - 6. `SAVE_CONFIG` (once completed) + 1. `DO_PROBE_CALIBRATE` + 2. Follow `z_offset` setup in Mainsail/Fluidd. + 3. `SAVE_CONFIG` (once completed) 6. Create a bed mesh. - 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` - 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` - 3. Proceed to next steps after both temperatures have been reached. - 4. `G28` - 5. `BED_MESH_CALIBRATE` - 6. `SAVE_CONFIG` (once completed) + 1. `DO_CREATE_MESH` + 2. `SAVE_CONFIG` (once completed) If you've made it here, then your printer has been Klipperized, and is ready to print!