SuperSlicer config bundle updated.

misc/SuperSlicer_config_bundle.ini

@@ -1,6 +1,6 @@
-# generated by SuperSlicer 2.4 on 2023-02-15 at 02:16:55 UTC
+# generated by SuperSlicer 2.4 on 2023-03-14 at 23:18:59 UTC
 
-[print:_Ellis_Decorative_45_Degree_11mm3-SOVOL]
+[print:_Ellis_Decorative_45_Degree_15mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -78,7 +78,7 @@ first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
 first_layer_flow_ratio = 100%
-first_layer_height = 0.25
+first_layer_height = 0.26
 first_layer_infill_speed = 60
 first_layer_min_speed = 0
 first_layer_size_compensation = -0.1
@@ -132,7 +132,7 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
 max_print_speed = 200
-max_volumetric_speed = 11
+max_volumetric_speed = 15
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -172,7 +172,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - Decorative 45 Degree (11mm3/s)
+print_settings_id = Ellis - Decorative 45 Degree (15mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -267,7 +267,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:_Ellis_Decorative_Standard_11mm3-SOVOL]
+[print:_Ellis_Decorative_Standard_15mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -345,7 +345,7 @@ first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
 first_layer_flow_ratio = 100%
-first_layer_height = 0.25
+first_layer_height = 0.26
 first_layer_infill_speed = 60
 first_layer_min_speed = 0
 first_layer_size_compensation = -0.1
@@ -399,7 +399,7 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
 max_print_speed = 200
-max_volumetric_speed = 11
+max_volumetric_speed = 15
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -439,7 +439,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - Decorative Standard (11mm3/s)
+print_settings_id = Ellis - Decorative Standard (15mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -534,7 +534,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:_Ellis_PIF_45_Degree_11mm3-SOVOL]
+[print:_Ellis_PIF_45_Degree_15mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -612,7 +612,7 @@ first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
 first_layer_flow_ratio = 100%
-first_layer_height = 0.25
+first_layer_height = 0.26
 first_layer_infill_speed = 60
 first_layer_min_speed = 0
 first_layer_size_compensation = -0.1
@@ -666,7 +666,7 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
 max_print_speed = 200
-max_volumetric_speed = 11
+max_volumetric_speed = 15
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -706,7 +706,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - PIF 45 Degree (11mm3/s)
+print_settings_id = Ellis - PIF 45 Degree (15mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -801,7 +801,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:_Ellis_PIF_Standard_11mm3-SOVOL]
+[print:_Ellis_PIF_Standard_15mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -879,7 +879,7 @@ first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
 first_layer_flow_ratio = 100%
-first_layer_height = 0.25
+first_layer_height = 0.26
 first_layer_infill_speed = 60
 first_layer_min_speed = 0
 first_layer_size_compensation = -0.1
@@ -933,7 +933,7 @@ ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
 max_print_speed = 200
-max_volumetric_speed = 11
+max_volumetric_speed = 15
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -973,7 +973,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - PIF Standard (11mm3/s)
+print_settings_id = Ellis - PIF Standard (15mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -1495,7 +1495,7 @@ full_fan_speed_layer = 4
 inherits = 
 max_fan_speed = 100
 max_speed_reduction = 90%
-min_fan_speed = 50
+min_fan_speed = 100
 min_print_speed = 15
 slowdown_below_layer_time = 15
 start_filament_gcode = ""
@@ -1591,7 +1591,7 @@ temperature = 250
 top_fan_speed = -1
 
 [filament:Eryone PETG - Blue]
-bed_temperature = 60
+bed_temperature = 70
 bridge_fan_speed = 100
 bridge_internal_fan_speed = -1
 chamber_temperature = 30
@@ -1602,15 +1602,15 @@ compatible_prints_condition =
 disable_fan_first_layers = 2
 end_filament_gcode = ""
 external_perimeter_fan_speed = -1
-extrusion_multiplier = 1
+extrusion_multiplier = 1.02
 fan_always_on = 1
 fan_below_layer_time = 20
-filament_colour = #2400FF
+filament_colour = #0F0EF0
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cooling_zone_pause = 0
-filament_cost = 20
+filament_cost = 29.36
 filament_custom_variables = ""
 filament_density = 1.45
 filament_deretract_speed = nil
@@ -1623,7 +1623,7 @@ filament_load_time = 0
 filament_loading_speed = 28
 filament_loading_speed_start = 3
 filament_max_overlap = 100%
-filament_max_speed = 120
+filament_max_speed = 0
 filament_max_volumetric_speed = 12
 filament_max_wipe_tower_speed = 0
 filament_melt_zone_pause = 0
@@ -1644,7 +1644,7 @@ filament_settings_id = ""
 filament_shrink = 100%
 filament_skinnydip_distance = 31
 filament_soluble = 0
-filament_spool_weight = 0
+filament_spool_weight = 1000
 filament_toolchange_delay = 0
 filament_toolchange_part_fan_speed = 50
 filament_toolchange_temp = 200
@@ -1663,13 +1663,13 @@ filament_wipe_inside_end = nil
 filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
-first_layer_bed_temperature = 60
+first_layer_bed_temperature = 70
-first_layer_temperature = 250
+first_layer_temperature = 240
 full_fan_speed_layer = 4
 inherits = 
 max_fan_speed = 100
 max_speed_reduction = 90%
-min_fan_speed = 50
+min_fan_speed = 100
 min_print_speed = 15
 slowdown_below_layer_time = 15
 start_filament_gcode = ""
@@ -1751,17 +1751,17 @@ filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
 first_layer_bed_temperature = 70
-first_layer_temperature = 245
+first_layer_temperature = 220
 full_fan_speed_layer = 4
 inherits = 
 max_fan_speed = 100
 max_speed_reduction = 90%
-min_fan_speed = 45
+min_fan_speed = 100
 min_print_speed = 15
 slowdown_below_layer_time = 15
 start_filament_gcode = ""
 support_material_interface_fan_speed = -1
-temperature = 235
+temperature = 220
 top_fan_speed = -1
 
 [filament:Eryone PETG - Galaxy Red]
@@ -1851,6 +1851,93 @@ support_material_interface_fan_speed = -1
 temperature = 235
 top_fan_speed = -1
 
+[filament:Eryone PLA - Matte Dual - Pink-Blue]
+bed_temperature = 60
+bridge_fan_speed = 100
+bridge_internal_fan_speed = -1
+chamber_temperature = 0
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+external_perimeter_fan_speed = -1
+extrusion_multiplier = 1.02
+fan_always_on = 1
+fan_below_layer_time = 20
+filament_colour = #927BB6
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 0
+filament_cooling_zone_pause = 0
+filament_cost = 26.91
+filament_custom_variables = ""
+filament_density = 1.23
+filament_deretract_speed = 30
+filament_diameter = 1.75
+filament_dip_extraction_speed = 70
+filament_dip_insertion_speed = 33
+filament_enable_toolchange_part_fan = 0
+filament_enable_toolchange_temp = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_overlap = 100%
+filament_max_speed = 0
+filament_max_volumetric_speed = 0
+filament_max_wipe_tower_speed = 0
+filament_melt_zone_pause = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ";Full spool weight: 1280g"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = 30
+filament_seam_gap = nil
+filament_settings_id = "ABS - KVP"
+filament_shrink = 100%
+filament_skinnydip_distance = 31
+filament_soluble = 0
+filament_spool_weight = 1000
+filament_toolchange_delay = 0
+filament_toolchange_part_fan_speed = 50
+filament_toolchange_temp = 200
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_use_fast_skinnydip = 0
+filament_use_skinnydip = 0
+filament_vendor = (Unknown)
+filament_wipe = nil
+filament_wipe_advanced_pigment = 0.5
+filament_wipe_extra_perimeter = nil
+filament_wipe_inside_depth = nil
+filament_wipe_inside_end = nil
+filament_wipe_inside_start = nil
+filament_wipe_only_crossing = nil
+filament_wipe_speed = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 210
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+max_speed_reduction = 90%
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\n"
+support_material_interface_fan_speed = -1
+temperature = 210
+top_fan_speed = -1
+
 [filament:Nuolei TPU - Light Blue]
 bed_temperature = 70
 bridge_fan_speed = 80
@@ -2278,7 +2365,7 @@ full_fan_speed_layer = 4
 inherits = 
 max_fan_speed = 100
 max_speed_reduction = 90%
-min_fan_speed = 100
+min_fan_speed = 70
 min_print_speed = 10
 slowdown_below_layer_time = 15
 start_filament_gcode = "; Filament gcode\n"
@@ -2373,9 +2460,96 @@ support_material_interface_fan_speed = -1
 temperature = 210
 top_fan_speed = -1
 
+[filament:eSun PLA+ Silver]
+bed_temperature = 60
+bridge_fan_speed = 100
+bridge_internal_fan_speed = -1
+chamber_temperature = 0
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+external_perimeter_fan_speed = -1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 20
+filament_colour = #0E5FED
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 0
+filament_cooling_zone_pause = 0
+filament_cost = 30
+filament_custom_variables = ""
+filament_density = 1.23
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_dip_extraction_speed = 70
+filament_dip_insertion_speed = 33
+filament_enable_toolchange_part_fan = 0
+filament_enable_toolchange_temp = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_overlap = 100%
+filament_max_speed = 0
+filament_max_volumetric_speed = 0
+filament_max_wipe_tower_speed = 0
+filament_melt_zone_pause = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ";Full spool weight: 1280g"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_seam_gap = nil
+filament_settings_id = "ABS - KVP"
+filament_shrink = 100%
+filament_skinnydip_distance = 31
+filament_soluble = 0
+filament_spool_weight = 1000
+filament_toolchange_delay = 0
+filament_toolchange_part_fan_speed = 50
+filament_toolchange_temp = 200
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_use_fast_skinnydip = 0
+filament_use_skinnydip = 0
+filament_vendor = (Unknown)
+filament_wipe = nil
+filament_wipe_advanced_pigment = 0.5
+filament_wipe_extra_perimeter = nil
+filament_wipe_inside_depth = nil
+filament_wipe_inside_end = nil
+filament_wipe_inside_start = nil
+filament_wipe_only_crossing = nil
+filament_wipe_speed = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 210
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+max_speed_reduction = 90%
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\n"
+support_material_interface_fan_speed = -1
+temperature = 210
+top_fan_speed = -1
+
 [printer:Sovol Sv06]
-bed_custom_model = /home/bassam/3dprinter/voron01-related/Ellis-SuperSlicer-Profiles/misc/SV06BuildPlate.stl
+bed_custom_model = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/SV06BuildPlate.stl
-bed_custom_texture = /home/bassam/3dprinter/voron01-related/Ellis-SuperSlicer-Profiles/misc/Texture_SV06.svg
+bed_custom_texture = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/sv06-buildplate-better.png
 bed_shape = 0x0,223x0,223x223,0x223
 before_layer_gcode = 
 between_objects_gcode = 
@@ -2384,7 +2558,7 @@ cooling_tube_length = 5
 cooling_tube_retraction = 91.5
 default_filament_profile = "Prusament PLA"
 default_print_profile = 0.15mm QUALITY @MK3
-deretract_speed = 60
+deretract_speed = 50
 end_gcode = PRINT_END
 extra_loading_move = -2
 extruder_colour = #FFE3CA
@@ -2452,7 +2626,7 @@ remaining_times_type = m73
 retract_before_travel = 2
 retract_before_wipe = 0%
 retract_layer_change = 1
-retract_length = 0.3
+retract_length = 0.4
 retract_length_toolchange = 10
 retract_lift = 0
 retract_lift_above = 0.2
@@ -2461,7 +2635,7 @@ retract_lift_first_layer = 0
 retract_lift_top = "All surfaces"
 retract_restart_extra = 0
 retract_restart_extra_toolchange = 0
-retract_speed = 60
+retract_speed = 50
 seam_gap = 15%
 silent_mode = 0
 single_extruder_multi_material = 0
@@ -2499,8 +2673,8 @@ z_offset = 0
 z_step = 0.005
 
 [presets]
-print = _Ellis_PIF_45_Degree_11mm3-SOVOL
+print = _Ellis_PIF_Standard_15mm3-SOVOL
 sla_print = 
 sla_material = 
 printer = Sovol Sv06
-filament = eSun PLA+ Blue
+filament = D3d PETG - Red