mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 21:41:15 +00:00
3285 lines
95 KiB
INI
3285 lines
95 KiB
INI
# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2024-05-07 at 05:08:14 UTC
|
|
|
|
[print:0.20mm QUALITY SV06 Ellis]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotonic
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0.6
|
|
bridge_acceleration = 3000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.95
|
|
bridge_speed = 140
|
|
brim_separation = 0.2
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition = printer_notes=~/.*PRINTER_VENDOR_PRUSA3D.*/ and printer_notes=~/.*PRINTER_MODEL_MK3.*/ and nozzle_diameter[0]==0.4
|
|
complete_objects = 0
|
|
default_acceleration = 3500
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0.1
|
|
enable_dynamic_overhang_speeds = 1
|
|
external_perimeter_acceleration = 750
|
|
external_perimeter_extrusion_width = 0.45
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 0
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 45
|
|
extrusion_width = 0.45
|
|
fill_angle = 45
|
|
fill_density = 15%
|
|
fill_pattern = cubic
|
|
first_layer_acceleration = 1000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.62
|
|
first_layer_height = 0.3
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0.0125
|
|
gcode_substitutions =
|
|
infill_acceleration = 3500
|
|
infill_anchor = 2.5
|
|
infill_anchor_max = 12
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.45
|
|
infill_first = 0
|
|
infill_overlap = 10%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 200
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 15
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = {input_filename_base}_{layer_height}mm_{printing_filament_types}_{printer_model}_{print_time}.gcode
|
|
overhang_speed_0 = 15
|
|
overhang_speed_1 = 15
|
|
overhang_speed_2 = 20
|
|
overhang_speed_3 = 25
|
|
overhangs = 1
|
|
perimeter_acceleration = 1000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.45
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 3
|
|
post_process =
|
|
print_settings_id =
|
|
raft_contact_distance = 0.2
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 1
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 3000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.62
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = 0
|
|
support_material_buildplate_only = 0
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.2
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 0
|
|
support_material_extrusion_width = 0.35
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 0
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 2
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 60%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 15%
|
|
thick_bridges = 1
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 1000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 3
|
|
top_solid_min_thickness = 0.6
|
|
travel_acceleration = 3500
|
|
travel_speed = 200
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 170
|
|
wipe_tower_y = 125
|
|
xy_size_compensation = 0
|
|
|
|
[print:Ellis_Decorative_Standard_15mm3]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0.6
|
|
bridge_acceleration = 3000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 3500
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 750
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 10%
|
|
fill_pattern = rectilinear
|
|
first_layer_acceleration = 1000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 3500
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.46
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 15
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 1000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.46
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 3
|
|
post_process =
|
|
print_settings_id = Ellis - Decorative Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 3000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 1
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 1000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 3500
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[print:Ellis_PIF_Standard_15mm3]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 5
|
|
bottom_solid_min_thickness = 1
|
|
bridge_acceleration = 3000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 3500
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 750
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 40%
|
|
fill_pattern = grid
|
|
first_layer_acceleration = 1000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 3500
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.64
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 15
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 1000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.4
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 4
|
|
post_process =
|
|
print_settings_id = Ellis - PIF Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 3000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 1000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 3500
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[print:_Ellis_Decorative_Standard_15mm3_CoreXY-Speeds]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0.6
|
|
bridge_acceleration = 5000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 4000
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 1000
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 10%
|
|
fill_pattern = rectilinear
|
|
first_layer_acceleration = 2000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 7000
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.46
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 15
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 2000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.46
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 3
|
|
post_process =
|
|
print_settings_id = Ellis - Decorative Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 5000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 1
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 2000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 10000
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[print:_Ellis_PIF_Standard_15mm3_CoreXY-Speeds]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 5
|
|
bottom_solid_min_thickness = 1
|
|
bridge_acceleration = 5000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 4000
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 1000
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 40%
|
|
fill_pattern = grid
|
|
first_layer_acceleration = 2000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 7000
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.64
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 15
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 2000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.4
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 4
|
|
post_process =
|
|
print_settings_id = Ellis - PIF Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 5000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 2000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 10000
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[print:__Ellis_Decorative_Standard_24mm3_CoreXY-Speeds]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 3
|
|
bottom_solid_min_thickness = 0.6
|
|
bridge_acceleration = 5000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 4000
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 1000
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 10%
|
|
fill_pattern = rectilinear
|
|
first_layer_acceleration = 2000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 7000
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.46
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 24
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 2000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.46
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 3
|
|
post_process =
|
|
print_settings_id = Ellis - Decorative Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 5000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 1
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 2000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 10000
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[print:__Ellis_PIF_Standard_24mm3_CoreXY-Speeds]
|
|
avoid_crossing_curled_overhangs = 0
|
|
avoid_crossing_perimeters = 0
|
|
avoid_crossing_perimeters_max_detour = 0
|
|
bottom_fill_pattern = monotoniclines
|
|
bottom_solid_layers = 5
|
|
bottom_solid_min_thickness = 1
|
|
bridge_acceleration = 5000
|
|
bridge_angle = 0
|
|
bridge_flow_ratio = 0.85
|
|
bridge_speed = 140
|
|
brim_separation = 0
|
|
brim_type = outer_only
|
|
brim_width = 0
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
complete_objects = 0
|
|
default_acceleration = 4000
|
|
dont_support_bridges = 1
|
|
draft_shield = disabled
|
|
elefant_foot_compensation = 0
|
|
enable_dynamic_overhang_speeds = 0
|
|
external_perimeter_acceleration = 1000
|
|
external_perimeter_extrusion_width = 0.4
|
|
external_perimeter_speed = 80
|
|
external_perimeters_first = 0
|
|
extra_perimeters = 0
|
|
extra_perimeters_on_overhangs = 1
|
|
extruder_clearance_height = 20
|
|
extruder_clearance_radius = 20
|
|
extrusion_width = 0.46
|
|
fill_angle = 45
|
|
fill_density = 40%
|
|
fill_pattern = grid
|
|
first_layer_acceleration = 2000
|
|
first_layer_acceleration_over_raft = 0
|
|
first_layer_extrusion_width = 0.5
|
|
first_layer_height = 0.26
|
|
first_layer_speed = 30
|
|
first_layer_speed_over_raft = 30
|
|
fuzzy_skin = none
|
|
fuzzy_skin_point_dist = 0.8
|
|
fuzzy_skin_thickness = 0.3
|
|
gap_fill_enabled = 1
|
|
gap_fill_speed = 30
|
|
gcode_comments = 0
|
|
gcode_label_objects = 1
|
|
gcode_resolution = 0
|
|
gcode_substitutions =
|
|
infill_acceleration = 7000
|
|
infill_anchor = 600%
|
|
infill_anchor_max = 400%
|
|
infill_every_layers = 1
|
|
infill_extruder = 1
|
|
infill_extrusion_width = 0.64
|
|
infill_first = 0
|
|
infill_overlap = 25%
|
|
infill_speed = 300
|
|
inherits =
|
|
interface_shells = 0
|
|
ironing = 0
|
|
ironing_flowrate = 15%
|
|
ironing_spacing = 0.1
|
|
ironing_speed = 15
|
|
ironing_type = top
|
|
layer_height = 0.2
|
|
max_print_speed = 300
|
|
max_volumetric_extrusion_rate_slope_negative = 0
|
|
max_volumetric_extrusion_rate_slope_positive = 0
|
|
max_volumetric_speed = 24
|
|
min_bead_width = 85%
|
|
min_feature_size = 25%
|
|
min_skirt_length = 20
|
|
mmu_segmented_region_interlocking_depth = 0
|
|
mmu_segmented_region_max_width = 0
|
|
notes =
|
|
only_retract_when_crossing_perimeters = 1
|
|
ooze_prevention = 0
|
|
output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
|
|
overhang_speed_0 = 75%
|
|
overhang_speed_1 = 80%
|
|
overhang_speed_2 = 90%
|
|
overhang_speed_3 = 100%
|
|
overhangs = 1
|
|
perimeter_acceleration = 2000
|
|
perimeter_extruder = 1
|
|
perimeter_extrusion_width = 0.4
|
|
perimeter_generator = arachne
|
|
perimeter_speed = 150
|
|
perimeters = 4
|
|
post_process =
|
|
print_settings_id = Ellis - PIF Standard (15mm³)
|
|
raft_contact_distance = 0.1
|
|
raft_expansion = 1.5
|
|
raft_first_layer_density = 90%
|
|
raft_first_layer_expansion = 3
|
|
raft_layers = 0
|
|
resolution = 0.0125
|
|
seam_position = aligned
|
|
single_extruder_multi_material_priming = 1
|
|
skirt_distance = 3
|
|
skirt_height = 1
|
|
skirts = 1
|
|
slice_closing_radius = 0.049
|
|
slicing_mode = regular
|
|
small_perimeter_speed = 30
|
|
solid_infill_acceleration = 5000
|
|
solid_infill_below_area = 0
|
|
solid_infill_every_layers = 0
|
|
solid_infill_extruder = 1
|
|
solid_infill_extrusion_width = 0.56
|
|
solid_infill_speed = 200
|
|
spiral_vase = 0
|
|
staggered_inner_seams = 0
|
|
standby_temperature_delta = -5
|
|
support_material = 0
|
|
support_material_angle = 0
|
|
support_material_auto = 1
|
|
support_material_bottom_contact_distance = 0
|
|
support_material_bottom_interface_layers = -1
|
|
support_material_buildplate_only = 1
|
|
support_material_closing_radius = 2
|
|
support_material_contact_distance = 0.1
|
|
support_material_enforce_layers = 0
|
|
support_material_extruder = 1
|
|
support_material_extrusion_width = 0
|
|
support_material_interface_contact_loops = 0
|
|
support_material_interface_extruder = 1
|
|
support_material_interface_layers = 2
|
|
support_material_interface_pattern = rectilinear
|
|
support_material_interface_spacing = 0.2
|
|
support_material_interface_speed = 100
|
|
support_material_pattern = rectilinear
|
|
support_material_spacing = 3
|
|
support_material_speed = 120
|
|
support_material_style = organic
|
|
support_material_synchronize_layers = 0
|
|
support_material_threshold = 30
|
|
support_material_with_sheath = 0
|
|
support_material_xy_spacing = 75%
|
|
support_tree_angle = 40
|
|
support_tree_angle_slow = 25
|
|
support_tree_branch_diameter = 2
|
|
support_tree_branch_diameter_angle = 5
|
|
support_tree_branch_diameter_double_wall = 3
|
|
support_tree_branch_distance = 1
|
|
support_tree_tip_diameter = 0.8
|
|
support_tree_top_rate = 30%
|
|
thick_bridges = 0
|
|
thin_walls = 1
|
|
threads = 16
|
|
top_fill_pattern = monotoniclines
|
|
top_infill_extrusion_width = 0.4
|
|
top_solid_infill_acceleration = 2000
|
|
top_solid_infill_speed = 60
|
|
top_solid_layers = 5
|
|
top_solid_min_thickness = 1
|
|
travel_acceleration = 10000
|
|
travel_speed = 300
|
|
travel_speed_z = 0
|
|
wall_distribution_count = 1
|
|
wall_transition_angle = 10
|
|
wall_transition_filter_deviation = 25%
|
|
wall_transition_length = 100%
|
|
wipe_tower = 0
|
|
wipe_tower_bridging = 10
|
|
wipe_tower_brim_width = 2
|
|
wipe_tower_cone_angle = 0
|
|
wipe_tower_extra_spacing = 100%
|
|
wipe_tower_extruder = 0
|
|
wipe_tower_no_sparse_layers = 0
|
|
wipe_tower_rotation_angle = 0
|
|
wipe_tower_width = 60
|
|
wipe_tower_x = 180
|
|
wipe_tower_y = 140
|
|
xy_size_compensation = 0
|
|
|
|
[filament:Basic PETG]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition = printer_model=~/.*Voron.*/ and printer_notes=~/.*E3DV6.*/
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #FF8000
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.27
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 8
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = Generic
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 240
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 30
|
|
min_fan_speed = 20
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 20
|
|
start_filament_gcode = ""
|
|
temperature = 245
|
|
|
|
[filament:D3D PLA+ Cyanblue]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #4BC1DB
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 30.5
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 210
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 210
|
|
|
|
[filament:D3D PLA+ Marble]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.97
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #0097B8
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 30.5
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 235
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 235
|
|
|
|
[filament:D3d PETG - Blue]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1.02
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #8FA094
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 20
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 245
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 60
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 245
|
|
|
|
[filament:D3d PETG - Purple]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1.02
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #8FA094
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 20
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.6
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 50
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 250
|
|
|
|
[filament:D3d PETG - Red]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #FF0002
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 20
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.8
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 240
|
|
|
|
[filament:D3d PETG - Silver]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #8FA094
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 20
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.8
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 50
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 250
|
|
|
|
[filament:ELEGOO PLA - Black]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #0E5FED
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 22.59
|
|
filament_density = 1.23
|
|
filament_deretract_speed = 25
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";Full spool weight: 1280g"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = 25
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 215
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 80
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 215
|
|
|
|
[filament:Eryone PETG - Blue]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1.02
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #0F0EF0
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 29.36
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 240
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 240
|
|
|
|
[filament:Eryone PETG - Galaxy Blue]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #331EB0
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 220
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 220
|
|
|
|
[filament:Eryone PETG - Galaxy Red]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #571B0D
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 245
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 50
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 235
|
|
|
|
[filament:Eryone PLA - Matte Dual - Pink-Blue]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #927BB6
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 26.91
|
|
filament_density = 1.23
|
|
filament_deretract_speed = 30
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";Full spool weight: 1280g"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = 30
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 220
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 220
|
|
|
|
[filament:GratKit PLA+ Grey]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #F6F6F6
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 19.35
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";Full spool weight: 1280g"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 230
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 230
|
|
|
|
[filament:Nuolei TPU - Light Blue]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #6FF2EC
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 18.07
|
|
filament_density = 1.22
|
|
filament_deretract_speed = 30
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = "- Original print temp was 235.\n- Retraction lenght was 0.3."
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = 30
|
|
filament_settings_id = "Generic FLEX"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 500
|
|
filament_toolchange_delay = 0
|
|
filament_type = FLEX
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = Generic
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 225
|
|
full_fan_speed_layer = 0
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "M900 K0"
|
|
temperature = 225
|
|
|
|
[filament:Overture PETG]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #FFC800
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 22
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.1
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 185
|
|
filament_toolchange_delay = 0
|
|
filament_type = PETG
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 30
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 5
|
|
start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.05"
|
|
temperature = 240
|
|
|
|
[filament:Polymaker PolyLite PETG - Silver]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #331EB0
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 15
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 245
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 65
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 245
|
|
|
|
[filament:Sparta3D ABS @VORON - Sky Blue, Sparkle]
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 20
|
|
filament_colour = #4BC1DB
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 35
|
|
filament_density = 1.04
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";max fan speed changed from 0 to 100"
|
|
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 100
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 25
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 240
|
|
|
|
[filament:Tinmorry PETG - Red]
|
|
bed_temperature = 70
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 2
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #A60001
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 22.02
|
|
filament_density = 1.45
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.7
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = 0.6
|
|
filament_retract_lift_above = 0.26
|
|
filament_retract_lift_below = 250
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PET
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 70
|
|
first_layer_temperature = 250
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 50
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 250
|
|
|
|
[filament:VOXELAB PLA Silk Rainbow]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #927BB6
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 25.92
|
|
filament_density = 1.23
|
|
filament_deretract_speed = 25
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = 0.6
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = 25
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 220
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 80
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 220
|
|
|
|
[filament:eSun ABS @VORON - Black]
|
|
bed_temperature = 100
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 20
|
|
filament_colour = #000000
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.04
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";max fan speed changed from 0 to 100"
|
|
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 100
|
|
first_layer_temperature = 260
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 20
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 245
|
|
|
|
[filament:eSun ABS @VORON - Green]
|
|
bed_temperature = 90
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 3
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = ""
|
|
extrusion_multiplier = 0.98
|
|
fan_always_on = 0
|
|
fan_below_layer_time = 20
|
|
filament_colour = #73E350
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 4
|
|
filament_cost = 30
|
|
filament_density = 1.04
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 12
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";max fan speed changed from 0 to 100"
|
|
filament_ramming_parameters = "120 100 5.70968 6.03226 7 8.25806 9 9.19355 9.3871 9.77419 10.129 10.3226 10.4516 10.5161| 0.05 5.69677 0.45 6.15484 0.95 8.76774 1.45 9.20323 1.95 9.95806 2.45 10.3871 2.95 10.5677 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = ""
|
|
filament_soluble = 0
|
|
filament_spool_weight = 0
|
|
filament_toolchange_delay = 0
|
|
filament_type = ABS
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 100
|
|
first_layer_temperature = 260
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 20
|
|
min_print_speed = 15
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = ""
|
|
temperature = 245
|
|
|
|
[filament:eSun PLA+ Blue]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #0E5FED
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 19.35
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";Full spool weight: 1280g"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 220
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 220
|
|
|
|
[filament:eSun PLA+ Magenta]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 0.97
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #707070
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 30
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ""
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 210
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 210
|
|
|
|
[filament:eSun PLA+ Silver]
|
|
bed_temperature = 60
|
|
bridge_fan_speed = 100
|
|
compatible_printers =
|
|
compatible_printers_condition =
|
|
compatible_prints =
|
|
compatible_prints_condition =
|
|
cooling = 1
|
|
disable_fan_first_layers = 1
|
|
enable_dynamic_fan_speeds = 0
|
|
end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
|
|
extrusion_multiplier = 1
|
|
fan_always_on = 1
|
|
fan_below_layer_time = 20
|
|
filament_colour = #0E5FED
|
|
filament_cooling_final_speed = 3.4
|
|
filament_cooling_initial_speed = 2.2
|
|
filament_cooling_moves = 0
|
|
filament_cost = 30
|
|
filament_density = 1.23
|
|
filament_deretract_speed = nil
|
|
filament_diameter = 1.75
|
|
filament_load_time = 0
|
|
filament_loading_speed = 28
|
|
filament_loading_speed_start = 3
|
|
filament_max_volumetric_speed = 0
|
|
filament_minimal_purge_on_wipe_tower = 15
|
|
filament_multitool_ramming = 0
|
|
filament_multitool_ramming_flow = 10
|
|
filament_multitool_ramming_volume = 10
|
|
filament_notes = ";Full spool weight: 1280g"
|
|
filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
|
|
filament_retract_before_travel = nil
|
|
filament_retract_before_wipe = nil
|
|
filament_retract_layer_change = nil
|
|
filament_retract_length = nil
|
|
filament_retract_length_toolchange = nil
|
|
filament_retract_lift = nil
|
|
filament_retract_lift_above = nil
|
|
filament_retract_lift_below = nil
|
|
filament_retract_restart_extra = nil
|
|
filament_retract_restart_extra_toolchange = nil
|
|
filament_retract_speed = nil
|
|
filament_settings_id = "ABS - KVP"
|
|
filament_soluble = 0
|
|
filament_spool_weight = 1000
|
|
filament_toolchange_delay = 0
|
|
filament_type = PLA
|
|
filament_unload_time = 0
|
|
filament_unloading_speed = 90
|
|
filament_unloading_speed_start = 100
|
|
filament_vendor = (Unknown)
|
|
filament_wipe = nil
|
|
first_layer_bed_temperature = 60
|
|
first_layer_temperature = 210
|
|
full_fan_speed_layer = 4
|
|
idle_temperature = nil
|
|
inherits =
|
|
max_fan_speed = 100
|
|
min_fan_speed = 100
|
|
min_print_speed = 10
|
|
overhang_fan_speed_0 = 0
|
|
overhang_fan_speed_1 = 0
|
|
overhang_fan_speed_2 = 0
|
|
overhang_fan_speed_3 = 0
|
|
slowdown_below_layer_time = 15
|
|
start_filament_gcode = "; Filament gcode\n"
|
|
temperature = 210
|
|
|
|
[printer:Sovol SV06]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,223x0,223x223,0x223
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile = "Prusament PLA"
|
|
default_print_profile = 0.15mm QUALITY @MK3
|
|
deretract_speed = 40
|
|
end_gcode = PRINT_END
|
|
extra_loading_move = -2
|
|
extruder_colour = #FFE3CA
|
|
extruder_offset = 0x0
|
|
gcode_flavor = klipper
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 5000,5000
|
|
machine_max_acceleration_extruding = 1250,1250
|
|
machine_max_acceleration_retracting = 1250,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1000,960
|
|
machine_max_acceleration_y = 1000,960
|
|
machine_max_acceleration_z = 200,200
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 200,100
|
|
machine_max_feedrate_y = 200,100
|
|
machine_max_feedrate_z = 12,12
|
|
machine_max_jerk_e = 4.5,4.5
|
|
machine_max_jerk_x = 8,8
|
|
machine_max_jerk_y = 8,8
|
|
machine_max_jerk_z = 0.4,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 255
|
|
min_layer_height = 0.04
|
|
nozzle_diameter = 0.4
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = PAUSE
|
|
print_host =
|
|
printer_model =
|
|
printer_notes = ; For sequential printing,\n; set Extruder clearance\n; Radius: 65.33 (actual 64.33)\n; Height: 25.87 (actual 24.87)\n
|
|
printer_settings_id = Sovol Sv06
|
|
printer_technology = FFF
|
|
printer_variant = 0.4
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 1
|
|
retract_length = 0.5
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0.2
|
|
retract_lift_below = 250
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 0
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\nPURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code
|
|
template_custom_gcode =
|
|
thumbnails = 32x32,400x300
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[printer:Sovol SV06 Plus]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,300x0,300x300,0x300
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile = "Prusament PLA"
|
|
default_print_profile = 0.15mm QUALITY @MK3
|
|
deretract_speed = 40
|
|
end_gcode = PRINT_END
|
|
extra_loading_move = -2
|
|
extruder_colour = #FFE3CA
|
|
extruder_offset = 0x0
|
|
gcode_flavor = klipper
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 5000,5000
|
|
machine_max_acceleration_extruding = 1250,1250
|
|
machine_max_acceleration_retracting = 1250,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1000,960
|
|
machine_max_acceleration_y = 1000,960
|
|
machine_max_acceleration_z = 200,200
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 200,100
|
|
machine_max_feedrate_y = 200,100
|
|
machine_max_feedrate_z = 12,12
|
|
machine_max_jerk_e = 4.5,4.5
|
|
machine_max_jerk_x = 8,8
|
|
machine_max_jerk_y = 8,8
|
|
machine_max_jerk_z = 0.4,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 340
|
|
min_layer_height = 0.04
|
|
nozzle_diameter = 0.4
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = PAUSE
|
|
print_host =
|
|
printer_model =
|
|
printer_notes = ; For sequential printing,\n; set Extruder clearance\n; Radius: 65.33 (actual 64.33)\n; Height: 34.85 (actual 33.85)\n; Values pulled from modes; you should verify for your unit.\n
|
|
printer_settings_id = Sovol Sv06
|
|
printer_technology = FFF
|
|
printer_variant = 0.4
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 1
|
|
retract_length = 0.5
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0.2
|
|
retract_lift_below = 250
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 0
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\nPURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code
|
|
template_custom_gcode =
|
|
thumbnails = 32x32,400x300
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[printer:Sovol SV07]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,220x0,220x220,0x220
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile = "Prusament PLA"
|
|
default_print_profile = 0.15mm QUALITY @MK3
|
|
deretract_speed = 40
|
|
end_gcode = PRINT_END
|
|
extra_loading_move = -2
|
|
extruder_colour = #FFE3CA
|
|
extruder_offset = 0x0
|
|
gcode_flavor = klipper
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 5000,5000
|
|
machine_max_acceleration_extruding = 1250,1250
|
|
machine_max_acceleration_retracting = 1250,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1000,960
|
|
machine_max_acceleration_y = 1000,960
|
|
machine_max_acceleration_z = 200,200
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 200,100
|
|
machine_max_feedrate_y = 200,100
|
|
machine_max_feedrate_z = 12,12
|
|
machine_max_jerk_e = 4.5,4.5
|
|
machine_max_jerk_x = 8,8
|
|
machine_max_jerk_y = 8,8
|
|
machine_max_jerk_z = 0.4,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 250
|
|
min_layer_height = 0.04
|
|
nozzle_diameter = 0.4
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = PAUSE
|
|
print_host =
|
|
printer_model =
|
|
printer_notes = ; For sequential printing,\n; set Extruder clearance\n; Radius: ??? (actual ???)\n; Height: ??? (actual ???)\n
|
|
printer_settings_id = Sovol Sv06
|
|
printer_technology = FFF
|
|
printer_variant = 0.4
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 1
|
|
retract_length = 0.5
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0.2
|
|
retract_lift_below = 250
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 0
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\n; PURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code
|
|
template_custom_gcode =
|
|
thumbnails = 32x32,400x300
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[printer:Sovol SV07 Plus]
|
|
autoemit_temperature_commands = 1
|
|
bed_custom_model =
|
|
bed_custom_texture =
|
|
bed_shape = 0x0,300x0,300x300,0x300
|
|
before_layer_gcode =
|
|
between_objects_gcode =
|
|
color_change_gcode = M600
|
|
cooling_tube_length = 5
|
|
cooling_tube_retraction = 91.5
|
|
default_filament_profile = "Prusament PLA"
|
|
default_print_profile = 0.15mm QUALITY @MK3
|
|
deretract_speed = 40
|
|
end_gcode = PRINT_END
|
|
extra_loading_move = -2
|
|
extruder_colour = #FFE3CA
|
|
extruder_offset = 0x0
|
|
gcode_flavor = klipper
|
|
high_current_on_filament_swap = 0
|
|
host_type = octoprint
|
|
inherits =
|
|
layer_gcode =
|
|
machine_limits_usage = time_estimate_only
|
|
machine_max_acceleration_e = 5000,5000
|
|
machine_max_acceleration_extruding = 1250,1250
|
|
machine_max_acceleration_retracting = 1250,1250
|
|
machine_max_acceleration_travel = 1500,1250
|
|
machine_max_acceleration_x = 1000,960
|
|
machine_max_acceleration_y = 1000,960
|
|
machine_max_acceleration_z = 200,200
|
|
machine_max_feedrate_e = 120,120
|
|
machine_max_feedrate_x = 200,100
|
|
machine_max_feedrate_y = 200,100
|
|
machine_max_feedrate_z = 12,12
|
|
machine_max_jerk_e = 4.5,4.5
|
|
machine_max_jerk_x = 8,8
|
|
machine_max_jerk_y = 8,8
|
|
machine_max_jerk_z = 0.4,0.4
|
|
machine_min_extruding_rate = 0,0
|
|
machine_min_travel_rate = 0,0
|
|
max_layer_height = 0
|
|
max_print_height = 350
|
|
min_layer_height = 0.04
|
|
nozzle_diameter = 0.4
|
|
parking_pos_retraction = 92
|
|
pause_print_gcode = PAUSE
|
|
print_host =
|
|
printer_model =
|
|
printer_notes = ; For sequential printing,\n; set Extruder clearance\n; Radius: ??? (actual ???)\n; Height: ??? (actual ???)\n
|
|
printer_settings_id = Sovol Sv06
|
|
printer_technology = FFF
|
|
printer_variant = 0.4
|
|
printer_vendor =
|
|
printhost_apikey =
|
|
printhost_cafile =
|
|
remaining_times = 1
|
|
retract_before_travel = 2
|
|
retract_before_wipe = 0%
|
|
retract_layer_change = 1
|
|
retract_length = 0.5
|
|
retract_length_toolchange = 10
|
|
retract_lift = 0
|
|
retract_lift_above = 0.2
|
|
retract_lift_below = 250
|
|
retract_restart_extra = 0
|
|
retract_restart_extra_toolchange = 0
|
|
retract_speed = 40
|
|
silent_mode = 0
|
|
single_extruder_multi_material = 0
|
|
start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\n; PURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code
|
|
template_custom_gcode =
|
|
thumbnails = 32x32,400x300
|
|
thumbnails_format = PNG
|
|
toolchange_gcode =
|
|
use_firmware_retraction = 0
|
|
use_relative_e_distances = 1
|
|
use_volumetric_e = 0
|
|
variable_layer_height = 1
|
|
wipe = 0
|
|
z_offset = 0
|
|
|
|
[physical_printer:Local SV06]
|
|
host_type = octoprint
|
|
preset_name = Sovol SV06
|
|
preset_names = "Sovol SV06"
|
|
print_host = http://10.0.0.51
|
|
printer_technology = FFF
|
|
printhost_apikey =
|
|
printhost_authorization_type = key
|
|
printhost_cafile =
|
|
printhost_password =
|
|
printhost_port =
|
|
printhost_ssl_ignore_revoke = 0
|
|
printhost_user =
|
|
|
|
[physical_printer:Local SV06 Plus]
|
|
host_type = octoprint
|
|
preset_name = Sovol SV06 Plus
|
|
preset_names = "Sovol SV06 Plus"
|
|
print_host = http://10.0.0.51
|
|
printer_technology = FFF
|
|
printhost_apikey =
|
|
printhost_authorization_type = key
|
|
printhost_cafile =
|
|
printhost_password =
|
|
printhost_port =
|
|
printhost_ssl_ignore_revoke = 0
|
|
printhost_user =
|
|
|
|
[physical_printer:Local SV07]
|
|
host_type = octoprint
|
|
preset_name = Sovol SV07
|
|
preset_names = "Sovol SV07"
|
|
print_host = http://10.0.0.51
|
|
printer_technology = FFF
|
|
printhost_apikey =
|
|
printhost_authorization_type = key
|
|
printhost_cafile =
|
|
printhost_password =
|
|
printhost_port =
|
|
printhost_ssl_ignore_revoke = 0
|
|
printhost_user =
|
|
|
|
[physical_printer:Local SV07 Plus]
|
|
host_type = octoprint
|
|
preset_name = Sovol SV07 Plus
|
|
preset_names = "Sovol SV07 Plus"
|
|
print_host = http://10.0.0.51
|
|
printer_technology = FFF
|
|
printhost_apikey =
|
|
printhost_authorization_type = key
|
|
printhost_cafile =
|
|
printhost_password =
|
|
printhost_port =
|
|
printhost_ssl_ignore_revoke = 0
|
|
printhost_user =
|
|
|
|
[presets]
|
|
print = Ellis_PIF_Standard_15mm3
|
|
sla_print =
|
|
sla_material =
|
|
printer = Sovol SV06
|
|
filament = eSun PLA+ Blue
|
|
physical_printer =
|