mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 21:41:15 +00:00
294 lines
6.1 KiB
INI
294 lines
6.1 KiB
INI
# This file contains pin mappings for the stock Sovol SV06.
|
|
#
|
|
# Using the wrong firmware, or wrong configuration, has the potential to destroy
|
|
# your 3D printer.
|
|
#
|
|
# ⚠️⚡☢️ USE AT YOUR OWN RISK! YOU HAVE BEEN WARNED! ☢️⚡⚠️
|
|
#
|
|
# See https://www.klipper3d.org/Config_Reference.html for configuration reference.
|
|
|
|
[include ./cfgs/macros.cfg]
|
|
[include ./cfgs/TEST_SPEED.cfg]
|
|
[include ./cfgs/PARKING.cfg]
|
|
[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
|
|
[include ./cfgs/beeper.cfg]
|
|
|
|
# NOTE Uncomment the ONE of the following lines if you're using an adxl345
|
|
# [include ./cfgs/adxl-rp2040.cfg]
|
|
# [include ./cfgs/adxl-direct.cfg]
|
|
|
|
[mcu]
|
|
# NOTE Obtain definition by "ls -l /dev/serial/by-id/"
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 15
|
|
max_z_accel: 45
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC1
|
|
run_current: 0.860
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA5
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC0
|
|
run_current: 0.900
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA6
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -3
|
|
position_max: 258
|
|
homing_speed: 5
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PA15
|
|
run_current: 1.000
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
diag_pin: PA7
|
|
|
|
# DELETEME
|
|
# [thermistor sovol_thermistor]
|
|
# temperature1: 25
|
|
# resistance1: 94162
|
|
# beta: 4160
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: !PB3
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 4.65
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC5
|
|
min_temp: 0
|
|
max_temp: 300
|
|
max_extrude_only_distance: 150.0
|
|
pressure_advance: 0.027
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC14
|
|
run_current: 0.550
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
|
|
[heater_bed]
|
|
heater_pin: PA2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[fan]
|
|
pin: PA0
|
|
|
|
[probe]
|
|
pin: PB1
|
|
x_offset: 27
|
|
y_offset: -20
|
|
# z_offset: 0
|
|
samples: 3
|
|
# samples_result: median
|
|
samples_tolerance: 0.01
|
|
samples_tolerance_retries: 5
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 195.0, 173.5
|
|
# home_xy_position: 84.50, 135 # Probe is at the center of the bed
|
|
speed: 100.0
|
|
z_hop: 10
|
|
z_hop_speed: 15
|
|
|
|
[bed_mesh]
|
|
speed: 175
|
|
mesh_min: 27, 5
|
|
mesh_max: 222, 203 # 196, 203
|
|
probe_count: 5,5
|
|
algorithm: bicubic
|
|
fade_start: 1
|
|
fade_end: 10
|
|
# fade_target: 0 # NOTE
|
|
relative_reference_index: 15
|
|
|
|
[virtual_sdcard]
|
|
path: /home/pi/printer_data/gcodes
|
|
|
|
[temperature_sensor raspberry_pi]
|
|
sensor_type: temperature_host
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PB12
|
|
sclk_pin: PB13
|
|
sid_pin: PB15
|
|
encoder_pins: ^PB14, ^PB10
|
|
click_pin: ^!PB2
|
|
|
|
[input_shaper]
|
|
shaper_freq_x = 56.0
|
|
shaper_type_x: mzv
|
|
shaper_freq_y = 59.0
|
|
shaper_type_y: 3hump_ei
|
|
|
|
[bed_screws]
|
|
screw1: 26.5, 31
|
|
screw1_name: front left
|
|
screw2: 196.75, 31
|
|
screw2_name: front right
|
|
screw3: 196.75, 201
|
|
screw3_name: back right
|
|
screw4: 26.5, 201
|
|
screw4_name: back left
|
|
|
|
[screws_tilt_adjust]
|
|
screw1: 111.5, 116.5
|
|
screw1_name: center
|
|
screw2: 26.5, 31
|
|
screw2_name: front left
|
|
screw3: 196.75, 31
|
|
screw3_name: front right
|
|
screw4: 196.75, 201
|
|
screw4_name: back right
|
|
screw5: 26.5, 201
|
|
screw5_name: back left
|
|
speed: 50
|
|
horizontal_move_z: 10
|
|
screw_thread: CCW-M4
|
|
|
|
# // NOTE this is the pin for the filament switch, if you have one
|
|
# [filament_switch_sensor fil_sensor]
|
|
# switch_pin: PA4 # "Pulled-high"
|
|
|
|
# NOTE Cancel objects feature is enabled. If you're using a low powered device, comment out [exclude_object].
|
|
# Also see [file_manager] section in moonraker.conf.
|
|
[exclude_object]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 21.047
|
|
#*# pid_ki = 1.477
|
|
#*# pid_kd = 74.981
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 71.224
|
|
#*# pid_ki = 1.341
|
|
#*# pid_kd = 945.503
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 1.500
|
|
#*#
|
|
#*# [bed_mesh default-working]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.210625, 0.309375, 0.357500, 0.312500, 0.247500
|
|
#*# 0.218125, 0.330000, 0.409375, 0.385625, 0.313750
|
|
#*# 0.184375, 0.328125, 0.420625, 0.428125, 0.378750
|
|
#*# 0.086250, 0.257500, 0.386250, 0.418750, 0.392500
|
|
#*# 0.000000, 0.211250, 0.363125, 0.420000, 0.420000
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 203.0
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*#
|
|
#*# [bed_mesh default-v1]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.017708, -0.023125, -0.023542, -0.037500, -0.088750
|
|
#*# -0.034167, -0.051875, -0.035833, -0.037708, -0.091875
|
|
#*# -0.072500, -0.066875, -0.056042, -0.050208, -0.093333
|
|
#*# -0.075417, -0.074167, -0.051458, -0.054375, -0.095625
|
|
#*# -0.030833, -0.014583, -0.000625, -0.013333, -0.051667
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 203.0
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.094792, 0.076250, 0.085208, 0.068333, 0.012083
|
|
#*# 0.077917, 0.054375, 0.067500, 0.060208, 0.003542
|
|
#*# 0.038958, 0.037292, 0.043750, 0.049583, 0.006458
|
|
#*# 0.028333, 0.030000, 0.042292, 0.040000, 0.000000
|
|
#*# 0.068958, 0.078542, 0.091250, 0.076458, 0.033958
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 203.0
|