mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 21:41:15 +00:00
247 lines
5.0 KiB
INI
247 lines
5.0 KiB
INI
# This file contains pin mappings for the stock Sovol SV06.
|
|
#
|
|
# Using the wrong firmware, or wrong configuration, has the potential to destroy
|
|
# your 3D printer.
|
|
#
|
|
# ⚠️⚡☢️ USE AT YOUR OWN RISK! YOU HAVE BEEN WARNED! ☢️⚡⚠️
|
|
#
|
|
# See https://www.klipper3d.org/Config_Reference.html for configuration reference.
|
|
|
|
[include ./cfgs/macros.cfg]
|
|
[include ./cfgs/TEST_SPEED.cfg]
|
|
[include ./cfgs/PARKING.cfg]
|
|
[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
|
|
[include ./cfgs/beeper.cfg]
|
|
|
|
# NOTE Uncomment the ONE of the following lines if you're using an adxl345
|
|
# [include ./cfgs/adxl-rp2040.cfg]
|
|
# [include ./cfgs/adxl-direct.cfg]
|
|
|
|
[mcu]
|
|
# NOTE Obtain definition by "ls -l /dev/serial/by-id/"
|
|
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_accel_to_decel: 1500
|
|
max_z_velocity: 15
|
|
max_z_accel: 45
|
|
# square_corner_velocity: 6.0
|
|
|
|
[force_move]
|
|
enable_force_move: True
|
|
|
|
[stepper_x]
|
|
step_pin: PC2
|
|
dir_pin: !PB9
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_x:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PC1
|
|
run_current: 0.860
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA5
|
|
|
|
[stepper_y]
|
|
step_pin: PB8
|
|
dir_pin: PB7
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 40
|
|
endstop_pin: tmc2209_stepper_y:virtual_endstop
|
|
position_endstop: 0
|
|
position_max: 223
|
|
homing_speed: 40
|
|
homing_retract_dist: 0
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PC0
|
|
run_current: 0.900
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
driver_SGTHRS: 81
|
|
diag_pin: PA6
|
|
|
|
[stepper_z]
|
|
step_pin: PB6
|
|
dir_pin: !PB5
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 4
|
|
endstop_pin: probe:z_virtual_endstop
|
|
position_min: -3
|
|
position_max: 257
|
|
homing_speed: 5
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PA15
|
|
run_current: 1.000
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
diag_pin: PA7
|
|
|
|
[thermistor sovol_thermistor]
|
|
temperature1: 25
|
|
resistance1: 94162
|
|
beta: 4160
|
|
|
|
[extruder]
|
|
step_pin: PB4
|
|
dir_pin: !PB3
|
|
enable_pin: !PC3
|
|
microsteps: 32
|
|
rotation_distance: 4.65
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PA1
|
|
sensor_type: sovol_thermistor
|
|
sensor_pin: PC5
|
|
min_temp: 0
|
|
max_temp: 270
|
|
max_extrude_only_distance: 150.0
|
|
pressure_advance: 0.027
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: PC14
|
|
run_current: 0.550
|
|
stealthchop_threshold: 0
|
|
interpolate: False
|
|
sense_resistor: 0.150
|
|
uart_address: 3
|
|
|
|
[heater_bed]
|
|
heater_pin: PA2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC4
|
|
min_temp: 0
|
|
max_temp: 110
|
|
|
|
[fan]
|
|
pin: PA0
|
|
|
|
[probe]
|
|
pin: PB1
|
|
x_offset: 27
|
|
y_offset: -20
|
|
# z_offset: 0
|
|
samples: 5
|
|
samples_result: median
|
|
samples_tolerance: 0.01
|
|
samples_tolerance_retries: 5
|
|
|
|
[safe_z_home]
|
|
home_xy_position: 0, 223 # NOTE 111.50,111.50
|
|
speed: 100.0
|
|
z_hop: 10
|
|
z_hop_speed: 15
|
|
|
|
[bed_mesh]
|
|
speed: 150
|
|
mesh_min: 27, 5
|
|
mesh_max: 222, 203 # 196, 203
|
|
probe_count: 5,5
|
|
algorithm: bicubic
|
|
fade_start: 1
|
|
fade_end: 10
|
|
# NOTE fade_target: 0
|
|
relative_reference_index: 20 # NOTE
|
|
|
|
[virtual_sdcard]
|
|
path: /home/pi/printer_data/gcodes
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PB12
|
|
sclk_pin: PB13
|
|
sid_pin: PB15
|
|
encoder_pins: ^PB14, ^PB10
|
|
click_pin: ^!PB2
|
|
|
|
[input_shaper]
|
|
shaper_freq_x = 56.0
|
|
shaper_type_x: mzv
|
|
shaper_freq_y = 59.0
|
|
shaper_type_y: 3hump_ei
|
|
|
|
# // NOTE this is the pin for the filament switch, if you have one
|
|
# [filament_switch_sensor fil_sensor]
|
|
# switch_pin: PA4
|
|
|
|
# NOTE Cancel objects feature is enabled. If you're using a low powered device, comment out [exclude_object].
|
|
# Also see [file_manager] section in moonraker.conf.
|
|
[exclude_object]
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 21.047
|
|
#*# pid_ki = 1.477
|
|
#*# pid_kd = 74.981
|
|
#*#
|
|
#*# [heater_bed]
|
|
#*# control = pid
|
|
#*# pid_kp = 71.224
|
|
#*# pid_ki = 1.341
|
|
#*# pid_kd = 945.503
|
|
#*#
|
|
#*# [probe]
|
|
#*# z_offset = 1.550
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.227500, 0.317500, 0.359375, 0.323125, 0.245000
|
|
#*# 0.207500, 0.327500, 0.398125, 0.376875, 0.298125
|
|
#*# 0.170625, 0.326250, 0.414375, 0.420625, 0.367500
|
|
#*# 0.093750, 0.266250, 0.387500, 0.415000, 0.390625
|
|
#*# 0.000000, 0.213750, 0.365000, 0.426875, 0.421250
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 203.0
|
|
#*#
|
|
#*# [bed_mesh default1]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# -0.290000, -0.178125, -0.134375, -0.185625, -0.292500
|
|
#*# -0.275000, -0.152500, -0.086250, -0.121250, -0.213125
|
|
#*# -0.301250, -0.151875, -0.066250, -0.077500, -0.137500
|
|
#*# -0.393750, -0.231875, -0.118125, -0.110000, -0.125625
|
|
#*# -0.500000, -0.297500, -0.160625, -0.113125, -0.076875
|
|
#*# x_count = 5
|
|
#*# y_count = 5
|
|
#*# mesh_x_pps = 2
|
|
#*# mesh_y_pps = 2
|
|
#*# algo = bicubic
|
|
#*# tension = 0.2
|
|
#*# min_x = 27.0
|
|
#*# max_x = 222.0
|
|
#*# min_y = 5.0
|
|
#*# max_y = 203.0
|