# 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration
This branch contains the Klipper configuration and firmware for the **Sovol SV06** 3D printer with the **BTT SKR-Mini-E3-V3.0** motherboard.
For the Sovol SV06 with stock hardware, please refer to the [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch.
For the Sovol SV06 Plus, please refer to the [sv06-plus](https://github.com/bassamanator/Sovol-SV06-firmware/tree/sv06-plus) branch.
For all other 3D printers, please switch to the [any-printer](https://github.com/bassamanator/Sovol-SV06-firmware/tree/any-printer) branch.
I am creating these files for my personal use and cannot be held responsible for what it might do to your printer. Use at your own risk.
⚠️ I am only 99% confident that this branch is production ready. Proceed with caution.
🙏🏻🙌🏻 A big thanks to [transistor1](https://github.com/transistor1) for getting this `printer.cfg` up an running to begin with.
## Installation Instructions
### Electronic Wiring
Wire cables according to the following diagram:
### Download Firmware
💡 The firmware files are located in `misc/skr-mini`.
💡 Be sure to download the `raw` files. Find out more about this [here](https://stackoverflow.com/questions/4604663/download-single-files-from-github).
Download [klipper-USB.bin](./misc/skr-mini/klipper-USB.bin) compiled by BTT. I also compiled a `klipper.bin` using the latest version of Klipper, however, it is untested; [klipper-v0.11.0-198-g33b18fd6-latest-UNTESTED.bin](./misc/skr-mini/klipper-v0.11.0-198-g33b18fd6-latest-UNTESTED.bin).
#### Alternatively, find instructions on how to build the firmware yourself [here](https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#build-firmware-image)
### Flash Firmware
⚠️ Make sure the microSD card has been prepared using the instructions found [here](https://github.com/bassamanator/Sovol-SV06-firmware#prepare-the-microsd-card-for-flashing).
1. Rename whatever firmware file you're using to `firmware.bin`. ⚠️ If the file is not renamed, the bootloader will not be updated properly.
2. Copy `firmware.bin` to the root directory of the microSD card.
3. Power off the skr-mini-E3-V3.0.
4. Insert the microSD card.
5. Power on the skr-mini-E3-V3.0.
6. After a few seconds, the skr-mini-E3-V3.0 should be flashed, but wait a full minute just to be sure.
7. You can confirm that the flash was successful, by running `ls -l /dev/serial/by-id/` or `ls -l /dev/serial/by-path/`. If the flash was successful, you'll see something like the following:
### Download Klipper Configuration
You can choose *either* of the 2 following methods.
### Method 1: Clone the Repository
1. `cd ~/printer_data/config`
2. Empty entire `~/printer_data/config` folder. Unfortunately, for safety reasons I will not post this command here. However, in linux, you can delete files via `rm filename`.
3. `git clone -b skr-mini-e3-v3 --single-branch https://github.com/bassamanator/Sovol-SV06-firmware.git .`
### Method 2: Download the ZIP
1. [Download](https://github.com/bassamanator/Sovol-SV06-firmware/archive/refs/heads/skr-mini-e3-v3.zip) the `ZIP` file containing the Klipper configuration.
2. See Step 2 in Method 1.
3. The parent folder in the `ZIP` is `Sovol-SV06-firmware-skr-mini-e3-v3`. This is relevant in the next step.
4. Extract **only** the *contents* of the parent folder into `~/printer_data/config`.
#### Once you've cloned or downloaded the configuration, please follow instructions found in [Initial Steps](https://github.com/bassamanator/Sovol-SV06-firmware#initial-steps).
# Sources
- https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#how-to-use-klipper-on-skr-mini-e3-v30
- https://forum.sovol3d.com/t/sv06-mit-skr-e3-mini-v3/1189/24
- https://github.com/bassamanator/everything-sovol-sv06/discussions/14