Adjusted readme.

Added firmware location to Flash Firmware section.

README.md

@@ -1,6 +1,8 @@
 # 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration
 
-This repository contains the Klipper configuration and firmware for the Sovol SV06 3D printer with completely *stock hardware*.
+This repository contains the Klipper configuration and firmware for the **Sovol SV06** 3D printer with completely *stock hardware*.
+
+If you wanted to use the One-Stop-Shop Klipper Configuration for a *different printer*, please switch to the [any-printer](https://github.com/bassamanator/Sovol-SV06-firmware/tree/any-printer) branch.
 
 I am creating these files for my personal use and cannot be held responsible for what it might do to your printer. Use at your own risk.
 
@@ -21,7 +23,7 @@ I am creating these files for my personal use and cannot be held responsible for
 ## To do:
 
 - [x] Replace M109/M190 with `TEMPERATURE_WAIT`.
-- [ ] Get the Ellis `TEST_SPEED` macro working.
+- [ ] ~~Get the Ellis `TEST_SPEED` macro working.~~ Does not seem safely doable on this printer.
 - [x] Add information about directory structure.
 - [x] Create FAQ section.
 - [x] Get filament sensor working with hotend PCB.
@@ -56,6 +58,8 @@ I work on this repository all the time and a lot of new features are coming. Wat
 
 💡 For the sake of simplicity, I will refer to the klipper firmware file as `klipper.bin` even though the actual filename is something along the lines of `klipper-v0.11.0-148-g52f4e20c.bin`.
 
+💡 The firmware file is located in the `misc` folder.
+
 ### Prepare the microSD Card for Flashing
 
 - Size: `8GB`. According to Sovol, the largest size that you can use is `16GB`.

cfgs/misc-macros.cfg

@@ -75,17 +75,34 @@ gcode:
     {% endif %}
 
 [gcode_macro PURGE_LINE]
-# https://github.com/JoeCat1207/V0.1-Purge-line-SuperSlicer/blob/main/Purgeline.txt
-# https://github.com/VoronDesign/Voron-Switchwire/blob/200cdae033c59ef81f67c4235469da7ca66d53a1/Firmware/skr_mini_e3_v2_config.cfg
 gcode:
     {% set PRE_PURGE_PRIME_LENGTH=printer["gcode_macro _globals"].pre_purge_prime_length|default(1.40)|float %}
     ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
-    G0 Y0 X0 F4000                         ; go to tongue of print bed
-    G1 Z0.4 F500.0                          ; move bed to nozzle
+
+    #   Get Boundaries
+    {% set max_x = printer.configfile.config["stepper_x"]["position_max"]|float %}
+    {% set max_y = printer.configfile.config["stepper_y"]["position_max"]|float %}
+    {% set max_z = printer.configfile.config["stepper_z"]["position_max"]|float %}
+    {% set extrudeAmount = 26.6 %}
+    {% set movementLength = 100.0 %}
+    {% set movementSpeed = 15 * 60 %}
+    {% set xStart = 0.5 %}
+    {% set yStart = 0.5 %}
+
+    #   Set safe speeds
+    {% set maxVelocity = printer.configfile.settings.printer.max_velocity|default(200)|int %}
+    {% set maxVelocityAdjusted =  (0.95 * maxVelocity * 60)|int  %}
+
     G92 E0.0                                ; reset extruder
+    G90                                     ; Absolute positioning
+    G0 X{xStart} Y{yStart} F{maxVelocityAdjusted}         ; move to purge position
+    G1 Z0.4 F500.0                          ; move to purge height
+    M83                                     ; Relative extrusion mode
     G1 E{PRE_PURGE_PRIME_LENGTH} F500       ; pre-purge prime LENGTH SHOULD MATCH YOUR PRINT_END RETRACT
-    G1 Y140 E35.0 F1200.0                   ; intro line 1
+    G1 X{xStart + movementLength} E{extrudeAmount} F{movementSpeed}       ; intro line 1
+    #G1 E-.5 F2100                                                                       # Retract
     G92 E0.0                                ; reset extruder
+    M82                                     ; Absolute extrusion mode
     G1 Z5.0                                 ; move nozzle to prevent scratch
 
 [gcode_macro CANCEL_PRINT]
@@ -125,11 +142,18 @@ gcode:
     ADJUST_FILAMENT_SENSOR_STATUS ENABLE=0
     CONDITIONAL_BEEP I=2 DUR=30 FREQ=8500                               ; NOTE Comment out this line to stop the beeps at the end of a print
     {% set PRE_PURGE_PRIME_LENGTH=printer["gcode_macro _globals"].pre_purge_prime_length|default(1.40)|float %}
+
     M400                                    ; wait for buffer to clear
     G92 E0                                  ; zero the extruder
     G1 E-{PRE_PURGE_PRIME_LENGTH} F400      ; retract filament
     G91                                     ; relative positioning
 
+    #   Set safe speeds
+    {% set zVelocity = printer.configfile.settings.printer.max_z_velocity|default(15)|int %}
+    {% set maxVelocity = printer.configfile.settings.printer.max_velocity|default(200)|int %}
+    {% set zVelocityAdjusted =  (0.95 * zVelocity * 60)|int  %}
+    {% set maxVelocityAdjusted =  (0.95 * maxVelocity * 60)|int  %}
+
     #   Get Boundaries
     {% set max_x = printer.configfile.config["stepper_x"]["position_max"]|float %}
     {% set max_y = printer.configfile.config["stepper_y"]["position_max"]|float %}
@@ -155,8 +179,8 @@ gcode:
         {% set z_safe = max_z - printer.toolhead.position.z %}
     {% endif %}
 
-    G0 Z{z_safe} F2000             ; move nozzle up
-    G0 X{x_safe} Y{y_safe} F9000   ; move nozzle to remove stringing
+    G0 Z{z_safe} F{zVelocityAdjusted}             ; move nozzle up
+    G0 X{x_safe} Y{y_safe} F{maxVelocityAdjusted}   ; move nozzle to remove stringing
     TURN_OFF_HEATERS
     M107                           ; turn off fan
     G90                            ; absolute positioning

printer.cfg

@@ -224,6 +224,8 @@ switch_pin: !PA4 # "Pulled-high"
 pause_on_runout: True
 insert_gcode:
     M117 Insert Detected
+    { action_respond_info("Insert Detected") }
 runout_gcode:
     M117 Runout Detected
+    { action_respond_info("Runout Detected") }
     CONDITIONAL_BEEP i=3 dur=300 freq=400