diff --git a/printer.cfg b/printer.cfg
index a666e74..f4977b2 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -174,6 +174,11 @@ pin: PA0
 #   Misc
 #####################################################################
 
+[idle_timeout]
+timeout: 600
+# gcode:
+    # Don't delete this section
+
 [display]
 lcd_type: st7920
 cs_pin: PB12
@@ -241,9 +246,9 @@ runout_gcode:
 #*#
 #*# [heater_bed]
 #*# control = pid
-#*# pid_kp = 68.676
-#*# pid_ki = 1.282
-#*# pid_kd = 919.396
+#*# pid_kp = 66.941
+#*# pid_ki = 1.190
+#*# pid_kd = 941.364
 #*#
 #*# [probe]
 #*# z_offset = 1.345
@@ -272,14 +277,14 @@ runout_gcode:
 #*# compensation_start_x = 27.0
 #*# compensation_end_x = 195.0
 #*#
-#*# [bed_mesh default-preNewNozzle]
+#*# [bed_mesh oldBed]
 #*# version = 1
 #*# points =
-#*# 	-0.038051, -0.033174, -0.038453, -0.061829, -0.123230
-#*# 	-0.073676, -0.058955, -0.051265, -0.057610, -0.126511
-#*# 	-0.108832, -0.063955, -0.058921, -0.063704, -0.125261
-#*# 	-0.123363, -0.074580, -0.063296, -0.081360, -0.140261
-#*# 	-0.074145, -0.020830, -0.011578, -0.024954, -0.074948
+#*# 	0.004384, -0.020865, -0.050803, -0.081005, -0.130833
+#*# 	-0.029366, -0.045709, -0.062678, -0.087255, -0.143646
+#*# 	-0.062178, -0.050084, -0.070178, -0.089755, -0.141302
+#*# 	-0.073897, -0.061647, -0.068459, -0.097411, -0.140521
+#*# 	-0.023428, -0.003678, -0.016740, -0.038661, -0.074427
 #*# min_x = 27.0
 #*# max_x = 222.0
 #*# min_y = 6.0
@@ -294,11 +299,11 @@ runout_gcode:
 #*# [bed_mesh default]
 #*# version = 1
 #*# points =
-#*# 	0.004384, -0.020865, -0.050803, -0.081005, -0.130833
-#*# 	-0.029366, -0.045709, -0.062678, -0.087255, -0.143646
-#*# 	-0.062178, -0.050084, -0.070178, -0.089755, -0.141302
-#*# 	-0.073897, -0.061647, -0.068459, -0.097411, -0.140521
-#*# 	-0.023428, -0.003678, -0.016740, -0.038661, -0.074427
+#*# 	  -0.012491, 0.011635, -0.008303, -0.048036, -0.075677
+#*# 	  -0.057647, -0.014928, -0.017990, -0.048349, -0.129583
+#*# 	  -0.097178, -0.051178, -0.057053, -0.088661, -0.149115
+#*# 	  -0.084522, -0.044147, -0.052678, -0.089599, -0.098177
+#*# 	  -0.025147, 0.026322, 0.019978, -0.032255, -0.102708
 #*# x_count = 5
 #*# y_count = 5
 #*# mesh_x_pps = 2