Minor cleanup.

klipper-printer-sovol-sv06.cfg

@@ -20,7 +20,7 @@
 [mcu]
 # Obtain definition by "ls -l /dev/serial/by-id/"
 serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
-# restart_method: command # NOTE is this needed?
+restart_method: command
 
 [printer]
 kinematics: cartesian
@@ -108,7 +108,6 @@ diag_pin: PA7
 #####################################################################
 
 [extruder]
-max_extrude_only_distance: 150.0
 step_pin: PB4
 dir_pin: !PB3
 enable_pin: !PC3
@@ -119,13 +118,10 @@ filament_diameter: 1.750
 heater_pin: PA1
 sensor_type: sovol_thermistor
 sensor_pin: PC5
-control: pid
-pid_kd: 86.991
-pid_kp: 21.479
-pid_ki: 1.326
 min_temp: 0
-max_temp: 300
-# min_extrude_temp: 190 # TODO enable after initial setup
+max_temp: 270
+min_extrude_temp: 190
+max_extrude_only_distance: 150.0
 
 [tmc2209 extruder]
 uart_pin: PC14
@@ -198,12 +194,8 @@ beta: 4160
 heater_pin: PA2
 sensor_type: EPCOS 100K B57560G104F
 sensor_pin: PC4
-control: pid
-pid_kp: 64.440
-pid_ki: 0.773
-pid_kd: 1343.571
 min_temp: 0
-max_temp: 130
+max_temp: 110
 
 [fan]
 pin: PA0
@@ -215,3 +207,18 @@ sclk_pin: PB13
 sid_pin: PB15
 encoder_pins: ^PB14, ^PB10
 click_pin: ^!PB2
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 21.047
+#*# pid_ki = 1.477
+#*# pid_kd = 74.981
+#*#
+#*# [heater_bed]
+#*# control = pid
+#*# pid_kp = 71.224
+#*# pid_ki = 1.341
+#*# pid_kd = 945.503

printer.cfg

@@ -108,7 +108,6 @@ diag_pin: PA7
 #####################################################################
 
 [extruder]
-max_extrude_only_distance: 150.0
 step_pin: PB4
 dir_pin: !PB3
 enable_pin: !PC3
@@ -119,13 +118,10 @@ filament_diameter: 1.750
 heater_pin: PA1
 sensor_type: sovol_thermistor
 sensor_pin: PC5
-#control: pid
-#pid_kd: 86.991
-#pid_kp: 21.479
-#pid_ki: 1.326
 min_temp: 0
 max_temp: 270
-# min_extrude_temp: 190 # TODO enable after initial setup
+min_extrude_temp: 190
+max_extrude_only_distance: 150.0
 
 [tmc2209 extruder]
 uart_pin: PC14
@@ -200,11 +196,6 @@ sensor_type: EPCOS 100K B57560G104F
 sensor_pin: PC4
 min_temp: 0
 max_temp: 110
-#control: pid
-#pid_kp: 64.440
-#pid_ki: 0.773
-#pid_kd: 1343.571
-
 
 [fan]
 pin: PA0