From df7e3d8212136e73f13fe27c47e8502c02d300da Mon Sep 17 00:00:00 2001 From: Bassam Husain Date: Sun, 19 Nov 2023 22:30:49 -0500 Subject: [PATCH] Adjust readme any-printer. --- README.md | 36 +++++++++++++++++++++++------------- 1 file changed, 23 insertions(+), 13 deletions(-) diff --git a/README.md b/README.md index 5e06e62..ad16abc 100644 --- a/README.md +++ b/README.md @@ -15,6 +15,7 @@ I am creating these files for my personal use and cannot be held responsible for - [Features](#features) - [Stay Up-to-Date](#stay-up-to-date) +- [Preface](#preface) - [Before You Begin](#before-you-begin) - [Installation Steps](#installation-steps) - [Download OSS Klipper Configuration](#download-oss-klipper-configuration) @@ -32,15 +33,15 @@ I am creating these files for my personal use and cannot be held responsible for - Filament runout sensor usage implemented. - Minimum configuration settings for Mainsail/Fluiddpi to work. - A SuperSlicer config bundle that contains what are considered by many to be the best print settings available for any FDM printer ([Ellis' SuperSlicer Profiles](https://github.com/AndrewEllis93/Ellis-SuperSlicer-Profiles)). -- `NEW` A PrusaSlicer config bundle based on Ellis' SuperSlicer Profiles. +- `NEW` dancing blob A PrusaSlicer config bundle based on Ellis' SuperSlicer Profiles. - Macros - - **Improved** mechanical gantry calibration/`G34` macro that provides the user audio feedback, and time to check the calibration. ⚠️ This is for i3 style printers only, see example video [here](https://youtu.be/aVdIeIIpUAk). + - **Improved** mechanical gantry calibration/`G34` macro that provides the user audio feedback, and time to check the calibration. - Misc macros: `PRINT_START`, `CANCEL_PRINT`, `PRINT_END`, `PAUSE`, `RESUME`. - Parking macros (parks the printhead at various locations): `PARKFRONT`, `PARKFRONTLOW`, `PARKREAR`, `PARKCENTER`, `PARKBED`. - Load/unload filament macros. - - Purge line macro. - - `NEW` `TEST_SPEED` macro. Find instructions [here](https://github.com/bassamanator/Sovol-SV06-firmware/blob/master/README.md#how-do-i-use-the-test_speed-macro). -- `NEW` Klipper Adaptive Meshing & Purging (KAMP) added (disabled by default)! Read about it [here](https://github.com/bassamanator/Sovol-SV06-firmware/blob/master/README.md#how-do-i-enable-kamp-klipper-adaptive-meshing--purging). + - `PURGE_LINE` macro. + - `NEW` dancing blob `TEST_SPEED` macro. Find instructions [here](#how-do-i-use-the-test_speed-macro). +- `NEW` dancing blob Klipper Adaptive Meshing & Purging (KAMP) added (disabled by default)! Read about it [here](#how-do-i-enable-kamp-klipper-adaptive-meshing--purging). ## Stay Up-to-Date @@ -50,12 +51,20 @@ Watch for releases and updates. githubstar +## Preface + +Although I've made switching over to Klipper as easy as is possible, it can still be a challenge for some, especially considering that most of you have likely never used GNU+Linux. Save yourself the frustration, and _fully read all the documentation on this page_. Also note that Klipper is not a _must_, and is not for everyone. You can stick with Marlin, and have a fine 3D printing experience. + ## Before You Begin +- This entire page is a **6 minute read**. Save yourself _hours of troubleshooting_ and read this documentation **fully!** - It is assumed that you already have a working `printer.cfg` and you already have your printer up and running Klipper. -- Know what you're getting into by reading this documentation _fully!_ -- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via a data USB cable. -- It is assumed that the username on the host device is `pi`. If that is not the case, you will have to manually edit `moonraker.conf` and `cfgs/misc-macros.cfg` and change any mentions of `/home/pi` to `/home/yourUserName`. +- The [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch of this repo contains step by step instructions on how to get Klipper going. If you are a beginner, you might find those instructions useful. +- Make sure your printer is in good physical condition, because print and travel speeds will be _a lot faster_ than they were before. Beginner's would be wise to go through the steps mentioned [here](https://github.com/bassamanator/everything-sovol-sv06/blob/main/initialsteps.md). Consider yourself warned. +- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via a data USB cable. 💡 Most of the micro USB cables that you find at home are _unlikely_ to be data cables, and it's not possible to tell just by looking. +- [Disable](https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#disable-usb-cable-5v-pin) the USB cable's 5V pin. +- It is also assumed that the username on the host device is `pi`. If that is not the case, you will have to manually edit `moonraker.conf` and `cfgs/misc-macros.cfg` and change any mentions of `/home/pi` to `/home/yourUserName`. +- Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section. - I would recommend searching for the word `NOTE` in this repository. There are roughly half a dozen short points amongst the various files that you should be aware of if you're using this configuration. ## Installation Steps @@ -66,9 +75,9 @@ Watch for releases and updates. 2. The parent folder in the `ZIP` is `Sovol-SV06-firmware-any-printer`. This is relevant in the next step. 3. Extract **only** the _contents_ of the parent folder into `~/printer_data/config`. -💡 **If** you get a warning that you already have a `moonraker.conf` (which you probably do since you're already up and running Klipper), **and** you're not using a low powered device such as a Raspberry Pi Zero, you need to simply paste the following into your _existing_ `moonraker.conf`: +💡 **If** you get a warning that you already have a `moonraker.conf` (which you probably do since you're already up and running Klipper), **and** you're not using a low powered device such as a Raspberry Pi Zero, you need to simply paste the following into your **existing** `moonraker.conf`: -``` +```yaml [file_manager] enable_object_processing: True ``` @@ -81,9 +90,10 @@ Simply add `[include ./osskc.cfg]` somewhere at the top of your `printer.cfg`. You need to adjust the start and end gcode in your slicer. The relevant macros are `PRINT_START` and `PRINT_END`. Find instructions [here](https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code). -If you would like to print a purge line before your print starts, at the end of your start gcode, on a new line add `PURGE_LINE`. ⚠️ This is just an **example**: +If you would like to print a purge line before your print starts, at the end of your start gcode, on a new line add `PURGE_LINE`. -``` +```yaml +# 🗒️ This is just an example PRINT_START ... PURGE_LINE ``` @@ -128,7 +138,7 @@ This repository contains many files and folders. Some are _necessary_ for this K ## Support Me -${\normalsize{\textcolor{goldenrod}{\texttt{Please ⭐ star this repository!}}}}$ +Please ⭐ star this repository! If you found my work useful, consider buying me a [Ko-fi](https://ko-fi.com/bassamanator).