From d69c2da3b849ae829d699522e6ff102f3c7f4310 Mon Sep 17 00:00:00 2001
From: Bassam Husain <bassam@Bassams-MacBook-Air.local>
Date: Mon, 26 Dec 2022 00:29:47 -0500
Subject: [PATCH] Added temperatures section in printer.cfg.

---
 README.md                      |  1 +
 klipper-printer-sovol-sv06.cfg | 48 +++++++++++++++++++++++++---------
 2 files changed, 37 insertions(+), 12 deletions(-)

diff --git a/README.md b/README.md
index 6b75243..fcb4154 100644
--- a/README.md
+++ b/README.md
@@ -65,4 +65,5 @@ sudo service klipper start
 ## Sources
 
 - https://docs.vorondesign.com/build/software/miniE3_v20_klipper.html
+- https://www.klipper3d.org/Installation.html#building-and-flashing-the-micro-controller
 - https://www.klipper3d.org/RPi_microcontroller.html#rpi-microcontroller
diff --git a/klipper-printer-sovol-sv06.cfg b/klipper-printer-sovol-sv06.cfg
index 7d9696c..e5923fc 100644
--- a/klipper-printer-sovol-sv06.cfg
+++ b/klipper-printer-sovol-sv06.cfg
@@ -9,6 +9,7 @@
 # that was flashed.
 
 # See docs/Config_Reference.md for a description of parameters.
+
 [include macros.cfg]
 [include mechanical_level_tmc2209.cfg]
 
@@ -19,18 +20,6 @@
 serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
 restart_method: command
 
-[adxl345]
-cs_pin: rpi:None
-
-[resonance_tester]
-accel_chip: adxl345
-probe_points: 110, 110, 20
-
-# [input_shaper]
-# shaper_freq_x = 114.6
-# shaper_type_x: mzv
-# shaper_freq_y = 77
-# shaper_type_y: mzv
 
 [printer]
 kinematics: cartesian
@@ -89,6 +78,28 @@ uart_address: 3
 driver_SGTHRS: 82
 diag_pin: PA6
 
+#####################################################################
+#   ADXL345 related Settings 
+#   https://www.klipper3d.org/Measuring_Resonances.html#adxl345
+#####################################################################
+
+# Uncomment this section if you're using an adxl345
+# [mcu rpi]
+# serial: /tmp/klipper_host_mcu
+
+# [adxl345]
+# cs_pin: rpi:None
+
+# [resonance_tester]
+# accel_chip: adxl345
+# probe_points: 110, 110, 20
+
+# [input_shaper]
+# shaper_freq_x = 114.6
+# shaper_type_x: mzv
+# shaper_freq_y = 77
+# shaper_type_y: mzv
+
 #####################################################################
 #   Z Stepper Settings
 #####################################################################
@@ -149,6 +160,19 @@ uart_address: 3
 #   Misc
 #####################################################################
 
+[virtual_sdcard]
+path: /home/pi/gcode_files/
+
+[temperature_sensor mcu_temp]
+sensor_type: temperature_mcu
+min_temp: 25
+max_temp: 80
+
+[temperature_sensor raspberry_pi]
+sensor_type: temperature_host
+min_temp: 25
+max_temp: 80 
+
 [thermistor sovol_thermistor]
 temperature1: 25
 resistance1: 94162