PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-08 21:41:15 +00:00
Code Issues Packages Projects Releases Wiki Activity

Pulled in readme from master.

Browse Source
This commit is contained in:
Bassam Husain
2023-04-05 00:51:22 -04:00
parent e501bdac3f
commit cc57e07c62
1 changed files with 24 additions and 8 deletions
Download Patch File Download Diff File Expand all files Collapse all files

32
README.md
View File

@@ -30,17 +30,23 @@ I work on this repository all the time and a lot of new features are coming. Wat
<img src="./images/githubstar.gif" width="500" alt='Raspberry Pi'/> <img src="./images/githubstar.gif" width="500" alt='Raspberry Pi'/>
# Preface
Although I've made switching over to Klipper as easy as is possible, it can still be a challenge for some, especially considering that most of you have likely never used GNU+Linux. Save yourself the fustration, and fully read all documentation found on this page. Also note that Klipper is not a *must*, and is not for everyone. You can stick with Marlin, and have a fine 3D printing experience.
# Installation Steps # Installation Steps
## Before You Begin ## Before You Begin
- Know what you're getting into by reading this documentation *fully!* - Read this documentation *fully!*
- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via USB. - Follow the steps in order.
- If an error was reported at a step, do no proceed to the next step.
- It is assumed that you are connected to your host Raspberry Pi (or other host device) via SSH, and that your printer motherboard is connected to the host via a data USB cable. Note that most of the micro USB cables that you find at home are *unlikely* to be data cables, and it's not possible to tell just by looking.
- It is also assumed that the username on the host device is `pi`. If that is not the case, you will have to manually edit `moonraker.conf` and `cfgs/misc-macros.cfg` and change any mentions of `/home/pi` to `/home/yourUserName`. - It is also assumed that the username on the host device is `pi`. If that is not the case, you will have to manually edit `moonraker.conf` and `cfgs/misc-macros.cfg` and change any mentions of `/home/pi` to `/home/yourUserName`.
- Klipper *must* be installed on the host Raspberry Pi for everything to work. Easiest is to use a [FluiddPi](https://docs.fluidd.xyz/installation/fluiddpi#download) or [MainsailOS](https://github.com/mainsail-crew/mainsail/releases/latest) image. - Klipper *must* be installed on the host Raspberry Pi for everything to work. Easiest is to use a [FluiddPi](https://docs.fluidd.xyz/installation/fluiddpi#download) or [MainsailOS](https://github.com/mainsail-crew/mainsail/releases/latest) image. [KIAUH](https://github.com/th33xitus/kiauh) is another excellent option, though it's not as simple as flashing MainsailOS on a microSD card, for example.
- It is assumed that there is one instance of Klipper installed. If you have multiple instances of Klipper installed, via `KIAUH` for example, then this guide is not for you. You can still use all the configs of course, but the steps in this guide will not work for you. - Robert Redford's performance in *Spy Game (2001)* was superb!
- It is assumed that there is one instance of Klipper installed. If you have multiple instances of Klipper installed, via `KIAUH` for example, then this guide is not for you. You can still use all the configs of course, but the steps in this guide will likely not work for you.
- Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section. - Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section.
- If you see any errors, or encounter any issues, please create an [Issue](https://github.com/bassamanator/Sovol-SV06-firmware/issues/new), or a [Pull request](https://github.com/bassamanator/Sovol-SV06-firmware/pulls).
- I would recommend searching for the word `NOTE` in this repository. There are roughly half a dozen short points amongst the various files that you should be aware of if you're using this configuration. - I would recommend searching for the word `NOTE` in this repository. There are roughly half a dozen short points amongst the various files that you should be aware of if you're using this configuration.
## Flash Firmware ## Flash Firmware
@@ -49,6 +55,8 @@ I work on this repository all the time and a lot of new features are coming. Wat
💡 For the sake of simplicity, I will refer to the klipper firmware file as `klipper.bin` even though the actual filename is something along the lines of `klipper-v0.11.0-148-g52f4e20c.bin`. 💡 For the sake of simplicity, I will refer to the klipper firmware file as `klipper.bin` even though the actual filename is something along the lines of `klipper-v0.11.0-148-g52f4e20c.bin`.
💡 The firmware file is located in the `misc` folder.
### Prepare the microSD Card for Flashing ### Prepare the microSD Card for Flashing
- Size: `8GB`. According to Sovol, the largest size that you can use is `16GB`. - Size: `8GB`. According to Sovol, the largest size that you can use is `16GB`.
@@ -72,13 +80,13 @@ You may find this [video](https://youtu.be/p6l253OJa34) useful.
You can choose *either* of the 2 following methods. You can choose *either* of the 2 following methods.
### Clone the Repository ### Method 1: Clone the Repository
1. `cd ~/printer_data/config` 1. `cd ~/printer_data/config`
2. Empty entire `~/printer_data/config` folder. Unfortunately, for safety reasons I will not post this command here. However, in linux, you can delete files via `rm filename`. 2. Empty entire `~/printer_data/config` folder. Unfortunately, for safety reasons I will not post this command here. However, in linux, you can delete files via `rm filename`.
3. `git clone -b sv06-plus --single-branch https://github.com/bassamanator/Sovol-SV06-firmware.git .` 3. `git clone -b sv06-plus --single-branch https://github.com/bassamanator/Sovol-SV06-firmware.git .`
### Download the ZIP ### Method 2: Download the ZIP
1. [Download](https://github.com/bassamanator/Sovol-SV06-firmware/archive/refs/heads/sv06-plus.zip) the `ZIP` file containing the Klipper configuration. 1. [Download](https://github.com/bassamanator/Sovol-SV06-firmware/archive/refs/heads/sv06-plus.zip) the `ZIP` file containing the Klipper configuration.
2. The parent folder in the `ZIP` is `Sovol-SV06-firmware-sv06-plus`. This is relevant in the next step. 2. The parent folder in the `ZIP` is `Sovol-SV06-firmware-sv06-plus`. This is relevant in the next step.
@@ -114,7 +122,7 @@ You can choose *either* of the 2 following methods.
3. `M106 S64` 3. `M106 S64`
4. `PID_CALIBRATE HEATER=extruder TARGET=245` 4. `PID_CALIBRATE HEATER=extruder TARGET=245`
5. `SAVE_CONFIG` (once completed) 5. `SAVE_CONFIG` (once completed)
5. Adjust `z_offset`. Make sure your nozzle if very clean. Paper test [reference](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test). 5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test).
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`
3. Proceed to next steps after both temperatures have been reached. 3. Proceed to next steps after both temperatures have been reached.
@@ -129,6 +137,14 @@ You can choose *either* of the 2 following methods.
5. `BED_MESH_CALIBRATE` 5. `BED_MESH_CALIBRATE`
6. `SAVE_CONFIG` (once completed) 6. `SAVE_CONFIG` (once completed)
If you've made it here, then your printer has been Klipperized, and is ready to print!
But first, adjust your slicer.
## Adjust Your Slicer
You need to adjust the start and end gcode in your slicer. The relevant macros are `PRINT_START` and `PRINT_END`. Find instructions [here](https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code).
## Directory Structure ## Directory Structure
This repository contains many files and folders. Some are *necessary* for this Klipper configuration to work, others are not. This repository contains many files and folders. Some are *necessary* for this Klipper configuration to work, others are not.