Turn function that allows prints to start when bed temp is 'target - 1' into a param in _globals.

.vscode/settings.json

@@ -70,4 +70,18 @@
 		"titleBar.inactiveForeground": "#e7e7e799"
 	},
 	"peacock.color": "#512e0a"
+	// "[html][jinja][jinja-html]": {
+	// 	"editor.formatOnSave": false,
+	// 	"editor.defaultFormatter": "monosans.djlint",
+	// 	"editor.detectIndentation": true,
+	// 	"editor.linkedEditing": true,
+	// 	"editor.tabSize": 4,
+
+	// 	"djlint.enableLinting": true,
+	// 	"djlint.profile": "jinja"
+	// },
+	// "djlint.showInstallError": true,
+	// "djlint.useVenv": false,
+	// "djlint.pythonPath": "/home/bassam/.local/share/uv/tools",
+	// "djlint.formatLanguages": ["django-html", "jinja", "jinja-html"]
 }

README.md

@@ -355,10 +355,12 @@ Edit the relevant file according to your needs.
 | `cfgs/misc-macros.cfg` | `[gcode_macro _globals]` |
 
 | Variable                           | Disable       | Enable         | Notes                                          |
-| ---------------------------------- | ------------- | ------------- | ---------------------------------------------- |
+| ---------------------------------- | ------------- | -------------- | ---------------------------------------------- |
 | `variable_beeping_enabled`         | `0`           | `1` (default)  |
 | `variable_filament_sensor_enabled` | `0` (default) | `1`            |
 | `variable_kamp_enable`             | `0` (default) | `1`            | See [here](#what-do-i-need-to-know-about-kamp) |
+| `variable_bed_temp_over`           | `0`           | `10` (default) | Speeds up print start                          |
+| `variable_bed_temp_not_exact`      | `0`           | `1` (default)  | Speeds up print start                          |
 
 ### How do I import a configuration bundle into SuperSlicer/PrusaSlicer?
 

cfgs/misc-macros.cfg

@@ -29,9 +29,11 @@ gcode:
     SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=0
 
 [gcode_macro _globals]
+# NOTE 0 = false; 1 = true
 variable_filament_sensor_enabled: 0 # NOTE Enable(1) or disable(0) the filament sensor, if one is connected
 variable_beeping_enabled: 1 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
-variable_bed_temp_over: 10 # NOTE Start print if bed temperature is over by this amount, otherwise wait for temperature drop
+variable_bed_temp_over: 10 # NOTE Start print if bed temperature is over by this amount. Set to 0 to disable, meaning, wait for temperature to drop
+variable_bed_temp_not_exact: 1 # NOTE Start print if bed temperature is `target temperature - 1` (but continue to heat until target is reached)
 variable_kamp_enable: 0 # NOTE Enable(1) or disable(0) KAMP (adaptive mesh)
 variable_pre_purge_prime_length: 1.40
 gcode:
@@ -75,12 +77,20 @@ gcode:
 [gcode_macro M190]
 rename_existing: M99190
 gcode:
-    #Parameters
+    # Global variables/settings
+    {% set bedtempNotExact = printer["gcode_macro _globals"].bed_temp_not_exact|default(1)|int %}
+
+    # Parameters
     {% set s = params.S|float %}
 
     M140 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %}   ; Set bed temp
     {% if s != 0 %}
-        TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s} MAXIMUM={s+1}  ; Wait for bed temp (within 1 degree)
+        {% if bedtempNotExact == 1 %}
+            TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s-1} MAXIMUM={s+1}  ; set & wait for bed temp (within -1 or +1 degree)
+            M140 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %} ; set & don't wait for bed temp
+        {% else %}
+            TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s} MAXIMUM={s+1}    ; Wait for bed temp (within +1 degree)
+        {% endif %}
     {% endif %}
 
 [gcode_macro PURGE_LINE]