diff --git a/cfgs/misc-macros.cfg b/cfgs/misc-macros.cfg
index 235368a..b1afe99 100644
--- a/cfgs/misc-macros.cfg
+++ b/cfgs/misc-macros.cfg
@@ -14,6 +14,11 @@ path: /home/pi/printer_data/gcodes
 [pause_resume]
 [display_status]
 
+# [delayed_gcode DISABLEFILAMENTSENSOR]
+# initial_duration: 1
+# gcode:
+#     SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=0
+
 [gcode_macro _globals]
 variable_filament_sensor_enabled: 0 # NOTE Enable(1) or disable(0) the filament sensor, if one is connected
 variable_beeping_enabled: 1 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
@@ -74,7 +79,7 @@ gcode:
 # https://github.com/VoronDesign/Voron-Switchwire/blob/200cdae033c59ef81f67c4235469da7ca66d53a1/Firmware/skr_mini_e3_v2_config.cfg
 gcode:
     {% set PRE_PURGE_PRIME_LENGTH=printer["gcode_macro _globals"].pre_purge_prime_length|default(1.40)|float %}
-
+    # ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
     G0 Y0 X0 F4000                         ; go to tongue of print bed
     G1 Z0.4 F500.0                          ; move bed to nozzle
     G92 E0.0                                ; reset extruder
@@ -93,12 +98,14 @@ gcode:
     BASE_CANCEL_PRINT
 
 [gcode_macro PRINT_START]
-gcode:        
+gcode:
     # Parameters
     {% set bedtemp = params.BED|int %}
     {% set hotendtemp = params.HOTEND|int %}
     {% set chambertemp = params.CHAMBER|default(0)|int %}
     
+    # ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
+
     G28 X Y
     # <insert your routines here>
     M140 S{bedtemp}                                                              ; set & don't wait for bed temp
@@ -115,7 +122,8 @@ gcode:
 
 [gcode_macro PRINT_END]
 gcode:
-    BEEP I=2 DUR=30 FREQ=8500 ; NOTE Comment out this line to stop the beeps at the end of a print
+    # ADJUST_FILAMENT_SENSOR_STATUS ENABLE=0
+    CONDITIONAL_BEEP I=2 DUR=30 FREQ=8500                               ; NOTE Comment out this line to stop the beeps at the end of a print
     {% set PRE_PURGE_PRIME_LENGTH=printer["gcode_macro _globals"].pre_purge_prime_length|default(1.40)|float %}
     M400                                    ; wait for buffer to clear
     G92 E0                                  ; zero the extruder
@@ -182,7 +190,8 @@ gcode:
         SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=zhop VALUE={z}                              ; set z hop variable for reference in resume macro
         SET_GCODE_VARIABLE MACRO=RESUME VARIABLE=etemp VALUE={printer['extruder'].target}    ; set hotend temp variable for reference in resume macro
 
-        # SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=0                                  ; disable filament sensor
+        # ADJUST_FILAMENT_SENSOR_STATUS ENABLE=0
+
         SAVE_GCODE_STATE NAME=PAUSE                                                          ; save current print position for resume
         BASE_PAUSE                                                                           ; pause print
         {% if (printer.gcode_move.position.z + z) < printer.toolhead.axis_maximum.z %}       ; check that zhop doesn't exceed z max
@@ -208,8 +217,8 @@ gcode:
     {% set e = params.E|default(2.5)|int %}                                          ; hotend prime amount (in mm)
 
     {% if printer['pause_resume'].is_paused|int == 1 %}
-        # SET_FILAMENT_SENSOR SENSOR=filament_sensor ENABLE=1                          ; enable filament sensor
-        #INITIAL_RGB                                                                    ; reset LCD color
+        # ADJUST_FILAMENT_SENSOR_STATUS ENABLE=1
+
         SET_IDLE_TIMEOUT TIMEOUT={printer.configfile.settings.idle_timeout.timeout}  ; set timeout back to configured value
         {% if etemp > 0 %}
             M109 S{etemp|int}                                                        ; wait for hotend to heat back up