README.md contains full instructions. Added current SuperSlicer config bundle. printer.cfg adjusted: Z position_min, improved comments.

misc/SuperSlicer_config_bundle.ini

@@ -1,6 +1,6 @@
-# generated by SuperSlicer 2.4 on 2023-02-03 at 00:05:10 UTC
+# generated by SuperSlicer 2.4 on 2023-02-15 at 02:16:55 UTC
 
-[print:Ellis_Decorative_45_Degree_15mm3]
+[print:_Ellis_Decorative_45_Degree_11mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -8,17 +8,17 @@ avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonicgapfill
 bottom_solid_layers = 3
 bottom_solid_min_thickness = 0.6
-bridge_acceleration = 5000
+bridge_acceleration = 3000
 bridge_angle = 0
 bridge_flow_ratio = 85%
-bridge_internal_acceleration = 5000
+bridge_internal_acceleration = 3000
 bridge_overlap = 50%
 bridge_overlap_min = 50%
 bridge_speed = 140
 bridge_speed_internal = 100%
 bridge_type = nozzle
 bridged_infill_margin = 300%
-brim_acceleration = 5000
+brim_acceleration = 1000
 brim_ears = 0
 brim_ears_detection_length = 1
 brim_ears_max_angle = 120
@@ -39,7 +39,7 @@ curve_smoothing_angle_concave = 0
 curve_smoothing_angle_convex = 0
 curve_smoothing_cutoff_dist = 2
 curve_smoothing_precision = 0
-default_acceleration = 4000
+default_acceleration = 3500
 default_speed = 100
 dont_support_bridges = 1
 draft_shield = disabled
@@ -49,7 +49,7 @@ enforce_retract_first_layer = 0
 ensure_vertical_shell_thickness = 0
 exact_last_layer_height = 0
 external_infill_margin = 4
-external_perimeter_acceleration = 1000
+external_perimeter_acceleration = 750
 external_perimeter_cut_corners = 0%
 external_perimeter_extrusion_spacing = 
 external_perimeter_extrusion_width = 0
@@ -73,7 +73,7 @@ fill_pattern = monotonic
 fill_smooth_distribution = 10%
 fill_smooth_width = 50%
 fill_top_flow_ratio = 100%
-first_layer_acceleration = 2000
+first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
@@ -88,7 +88,7 @@ first_layer_speed_over_raft = 30
 fuzzy_skin = none
 fuzzy_skin_point_dist = 200%
 fuzzy_skin_thickness = 150%
-gap_fill_acceleration = 2000
+gap_fill_acceleration = 1000
 gap_fill_enabled = 1
 gap_fill_flow_match_perimeter = 0%
 gap_fill_last = 1
@@ -99,12 +99,12 @@ gcode_comments = 0
 gcode_label_objects = 1
 gcode_resolution = 0
 gcode_substitutions = 
-hole_size_compensation = 0
+hole_size_compensation = 0.1
 hole_size_threshold = 100
 hole_to_polyhole = 0
 hole_to_polyhole_threshold = 0.01
 hole_to_polyhole_twisted = 1
-infill_acceleration = 7000
+infill_acceleration = 3500
 infill_anchor = 600%
 infill_anchor_max = 0
 infill_connection = connected
@@ -124,15 +124,15 @@ infill_speed = 300
 inherits = 
 interface_shells = 0
 ironing = 0
-ironing_acceleration = 2000
+ironing_acceleration = 1000
 ironing_angle = -1
 ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
-max_print_speed = 300
-max_volumetric_speed = 15
+max_print_speed = 200
+max_volumetric_speed = 11
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -150,13 +150,13 @@ only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
 over_bridge_flow_ratio = 100%
-overhangs_acceleration = 2000
+overhangs_acceleration = 1000
 overhangs_reverse = 0
 overhangs_reverse_threshold = 250%
 overhangs_speed = 100%
 overhangs_width = 75%
 overhangs_width_speed = 0
-perimeter_acceleration = 2000
+perimeter_acceleration = 1000
 perimeter_bonding = 0%
 perimeter_extruder = 1
 perimeter_extrusion_spacing = 
@@ -172,7 +172,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - Decorative 45 Degree (15mm3/s)
+print_settings_id = Ellis - Decorative 45 Degree (11mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -197,7 +197,7 @@ small_perimeter_max_length = 20
 small_perimeter_min_length = 6
 small_perimeter_speed = 30
 solid_fill_pattern = monotonic
-solid_infill_acceleration = 5000
+solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -209,7 +209,7 @@ solid_over_perimeters = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
-support_material_acceleration = 5000
+support_material_acceleration = 3500
 support_material_angle = 45
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
@@ -221,7 +221,7 @@ support_material_contact_distance_type = filament
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
-support_material_interface_acceleration = 5000
+support_material_interface_acceleration = 3500
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
@@ -239,7 +239,7 @@ support_material_xy_spacing = 75%
 thin_perimeters = 80%
 thin_perimeters_all = 20%
 thin_walls = 1
-thin_walls_acceleration = 2000
+thin_walls_acceleration = 750
 thin_walls_merge = 1
 thin_walls_min_width = 33%
 thin_walls_overlap = 50%
@@ -248,13 +248,13 @@ threads = 16
 top_fill_pattern = monotonicgapfill
 top_infill_extrusion_spacing = 
 top_infill_extrusion_width = 100%
-top_solid_infill_acceleration = 2000
+top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
 top_solid_min_thickness = 1
-travel_acceleration = 10000
+travel_acceleration = 3500
 travel_deceleration_use_target = 1
-travel_speed = 350
+travel_speed = 200
 travel_speed_z = 0
 wipe_tower = 0
 wipe_tower_bridging = 10
@@ -267,7 +267,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:Ellis_Decorative_Standard_15mm3]
+[print:_Ellis_Decorative_Standard_11mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -275,17 +275,17 @@ avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonicgapfill
 bottom_solid_layers = 3
 bottom_solid_min_thickness = 0.6
-bridge_acceleration = 5000
+bridge_acceleration = 3000
 bridge_angle = 0
 bridge_flow_ratio = 85%
-bridge_internal_acceleration = 5000
+bridge_internal_acceleration = 3000
 bridge_overlap = 50%
 bridge_overlap_min = 50%
 bridge_speed = 140
 bridge_speed_internal = 100%
 bridge_type = nozzle
 bridged_infill_margin = 300%
-brim_acceleration = 5000
+brim_acceleration = 1000
 brim_ears = 0
 brim_ears_detection_length = 1
 brim_ears_max_angle = 120
@@ -306,7 +306,7 @@ curve_smoothing_angle_concave = 0
 curve_smoothing_angle_convex = 0
 curve_smoothing_cutoff_dist = 2
 curve_smoothing_precision = 0
-default_acceleration = 4000
+default_acceleration = 3500
 default_speed = 100
 dont_support_bridges = 1
 draft_shield = disabled
@@ -316,7 +316,7 @@ enforce_retract_first_layer = 0
 ensure_vertical_shell_thickness = 0
 exact_last_layer_height = 0
 external_infill_margin = 4
-external_perimeter_acceleration = 1000
+external_perimeter_acceleration = 750
 external_perimeter_cut_corners = 0%
 external_perimeter_extrusion_spacing = 
 external_perimeter_extrusion_width = 0
@@ -340,7 +340,7 @@ fill_pattern = monotonic
 fill_smooth_distribution = 10%
 fill_smooth_width = 50%
 fill_top_flow_ratio = 100%
-first_layer_acceleration = 2000
+first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
@@ -355,7 +355,7 @@ first_layer_speed_over_raft = 30
 fuzzy_skin = none
 fuzzy_skin_point_dist = 200%
 fuzzy_skin_thickness = 150%
-gap_fill_acceleration = 2000
+gap_fill_acceleration = 1000
 gap_fill_enabled = 1
 gap_fill_flow_match_perimeter = 0%
 gap_fill_last = 1
@@ -366,12 +366,12 @@ gcode_comments = 0
 gcode_label_objects = 1
 gcode_resolution = 0
 gcode_substitutions = 
-hole_size_compensation = 0
+hole_size_compensation = 0.1
 hole_size_threshold = 100
 hole_to_polyhole = 0
 hole_to_polyhole_threshold = 0.01
 hole_to_polyhole_twisted = 1
-infill_acceleration = 7000
+infill_acceleration = 3500
 infill_anchor = 600%
 infill_anchor_max = 0
 infill_connection = connected
@@ -391,15 +391,15 @@ infill_speed = 300
 inherits = 
 interface_shells = 0
 ironing = 0
-ironing_acceleration = 2000
+ironing_acceleration = 1000
 ironing_angle = -1
 ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
-max_print_speed = 300
-max_volumetric_speed = 15
+max_print_speed = 200
+max_volumetric_speed = 11
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -417,13 +417,13 @@ only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
 over_bridge_flow_ratio = 100%
-overhangs_acceleration = 2000
+overhangs_acceleration = 1000
 overhangs_reverse = 0
 overhangs_reverse_threshold = 250%
 overhangs_speed = 100%
 overhangs_width = 75%
 overhangs_width_speed = 0
-perimeter_acceleration = 2000
+perimeter_acceleration = 1000
 perimeter_bonding = 0%
 perimeter_extruder = 1
 perimeter_extrusion_spacing = 
@@ -439,7 +439,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - Decorative Standard (15mm3/s)
+print_settings_id = Ellis - Decorative Standard (11mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -464,7 +464,7 @@ small_perimeter_max_length = 20
 small_perimeter_min_length = 6
 small_perimeter_speed = 30
 solid_fill_pattern = monotonic
-solid_infill_acceleration = 5000
+solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -476,7 +476,7 @@ solid_over_perimeters = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 1
-support_material_acceleration = 5000
+support_material_acceleration = 3500
 support_material_angle = 0
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
@@ -488,7 +488,7 @@ support_material_contact_distance_type = filament
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
-support_material_interface_acceleration = 5000
+support_material_interface_acceleration = 3500
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
@@ -506,7 +506,7 @@ support_material_xy_spacing = 75%
 thin_perimeters = 80%
 thin_perimeters_all = 20%
 thin_walls = 1
-thin_walls_acceleration = 2000
+thin_walls_acceleration = 750
 thin_walls_merge = 1
 thin_walls_min_width = 33%
 thin_walls_overlap = 50%
@@ -515,13 +515,13 @@ threads = 16
 top_fill_pattern = monotonicgapfill
 top_infill_extrusion_spacing = 
 top_infill_extrusion_width = 100%
-top_solid_infill_acceleration = 2000
+top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
 top_solid_min_thickness = 1
-travel_acceleration = 10000
+travel_acceleration = 3500
 travel_deceleration_use_target = 1
-travel_speed = 350
+travel_speed = 200
 travel_speed_z = 0
 wipe_tower = 0
 wipe_tower_bridging = 10
@@ -534,7 +534,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:Ellis_PIF_45_Degree_15mm3]
+[print:_Ellis_PIF_45_Degree_11mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -542,17 +542,17 @@ avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonicgapfill
 bottom_solid_layers = 5
 bottom_solid_min_thickness = 1
-bridge_acceleration = 5000
+bridge_acceleration = 3000
 bridge_angle = 0
 bridge_flow_ratio = 85%
-bridge_internal_acceleration = 5000
+bridge_internal_acceleration = 3000
 bridge_overlap = 50%
 bridge_overlap_min = 50%
 bridge_speed = 140
 bridge_speed_internal = 100%
 bridge_type = nozzle
 bridged_infill_margin = 300%
-brim_acceleration = 5000
+brim_acceleration = 1000
 brim_ears = 0
 brim_ears_detection_length = 1
 brim_ears_max_angle = 120
@@ -573,7 +573,7 @@ curve_smoothing_angle_concave = 0
 curve_smoothing_angle_convex = 0
 curve_smoothing_cutoff_dist = 2
 curve_smoothing_precision = 0
-default_acceleration = 4000
+default_acceleration = 3500
 default_speed = 100
 dont_support_bridges = 1
 draft_shield = disabled
@@ -583,7 +583,7 @@ enforce_retract_first_layer = 0
 ensure_vertical_shell_thickness = 0
 exact_last_layer_height = 0
 external_infill_margin = 4
-external_perimeter_acceleration = 1000
+external_perimeter_acceleration = 750
 external_perimeter_cut_corners = 0%
 external_perimeter_extrusion_spacing = 
 external_perimeter_extrusion_width = 100%
@@ -607,7 +607,7 @@ fill_pattern = grid
 fill_smooth_distribution = 10%
 fill_smooth_width = 50%
 fill_top_flow_ratio = 100%
-first_layer_acceleration = 2000
+first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
@@ -622,7 +622,7 @@ first_layer_speed_over_raft = 30
 fuzzy_skin = none
 fuzzy_skin_point_dist = 200%
 fuzzy_skin_thickness = 150%
-gap_fill_acceleration = 2000
+gap_fill_acceleration = 1000
 gap_fill_enabled = 1
 gap_fill_flow_match_perimeter = 0%
 gap_fill_last = 1
@@ -633,12 +633,12 @@ gcode_comments = 0
 gcode_label_objects = 1
 gcode_resolution = 0
 gcode_substitutions = 
-hole_size_compensation = 0
+hole_size_compensation = 0.1
 hole_size_threshold = 100
 hole_to_polyhole = 0
 hole_to_polyhole_threshold = 0.01
 hole_to_polyhole_twisted = 1
-infill_acceleration = 6500
+infill_acceleration = 3500
 infill_anchor = 600%
 infill_anchor_max = 0
 infill_connection = connected
@@ -658,15 +658,15 @@ infill_speed = 300
 inherits = 
 interface_shells = 0
 ironing = 0
-ironing_acceleration = 2000
+ironing_acceleration = 1000
 ironing_angle = -1
 ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
-max_print_speed = 300
-max_volumetric_speed = 15
+max_print_speed = 200
+max_volumetric_speed = 11
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -684,13 +684,13 @@ only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
 over_bridge_flow_ratio = 100%
-overhangs_acceleration = 2000
+overhangs_acceleration = 1000
 overhangs_reverse = 0
 overhangs_reverse_threshold = 250%
 overhangs_speed = 100%
 overhangs_width = 75%
 overhangs_width_speed = 0
-perimeter_acceleration = 2000
+perimeter_acceleration = 1000
 perimeter_bonding = 0%
 perimeter_extruder = 1
 perimeter_extrusion_spacing = 
@@ -706,7 +706,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - PIF 45 Degree (15mm3/s)
+print_settings_id = Ellis - PIF 45 Degree (11mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -731,7 +731,7 @@ small_perimeter_max_length = 20
 small_perimeter_min_length = 6
 small_perimeter_speed = 30
 solid_fill_pattern = monotonic
-solid_infill_acceleration = 5000
+solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -743,7 +743,7 @@ solid_over_perimeters = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
-support_material_acceleration = 5000
+support_material_acceleration = 3500
 support_material_angle = 45
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
@@ -755,7 +755,7 @@ support_material_contact_distance_type = filament
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
-support_material_interface_acceleration = 5000
+support_material_interface_acceleration = 3500
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
@@ -773,7 +773,7 @@ support_material_xy_spacing = 75%
 thin_perimeters = 80%
 thin_perimeters_all = 20%
 thin_walls = 1
-thin_walls_acceleration = 2000
+thin_walls_acceleration = 750
 thin_walls_merge = 1
 thin_walls_min_width = 33%
 thin_walls_overlap = 50%
@@ -782,13 +782,13 @@ threads = 16
 top_fill_pattern = monotonicgapfill
 top_infill_extrusion_spacing = 
 top_infill_extrusion_width = 100%
-top_solid_infill_acceleration = 2000
+top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
 top_solid_min_thickness = 1
-travel_acceleration = 6500
+travel_acceleration = 3500
 travel_deceleration_use_target = 1
-travel_speed = 350
+travel_speed = 200
 travel_speed_z = 0
 wipe_tower = 0
 wipe_tower_bridging = 10
@@ -801,7 +801,7 @@ wipe_tower_y = 140
 xy_inner_size_compensation = 0
 xy_size_compensation = 0
 
-[print:Ellis_PIF_Standard_15mm3]
+[print:_Ellis_PIF_Standard_11mm3-SOVOL]
 allow_empty_layers = 0
 avoid_crossing_not_first_layer = 1
 avoid_crossing_perimeters = 0
@@ -809,17 +809,17 @@ avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonicgapfill
 bottom_solid_layers = 5
 bottom_solid_min_thickness = 1
-bridge_acceleration = 5000
+bridge_acceleration = 3000
 bridge_angle = 0
 bridge_flow_ratio = 85%
-bridge_internal_acceleration = 5000
+bridge_internal_acceleration = 3000
 bridge_overlap = 50%
 bridge_overlap_min = 50%
 bridge_speed = 140
 bridge_speed_internal = 100%
 bridge_type = nozzle
 bridged_infill_margin = 300%
-brim_acceleration = 5000
+brim_acceleration = 1000
 brim_ears = 0
 brim_ears_detection_length = 1
 brim_ears_max_angle = 120
@@ -840,7 +840,7 @@ curve_smoothing_angle_concave = 0
 curve_smoothing_angle_convex = 0
 curve_smoothing_cutoff_dist = 2
 curve_smoothing_precision = 0
-default_acceleration = 4000
+default_acceleration = 3500
 default_speed = 100
 dont_support_bridges = 1
 draft_shield = disabled
@@ -850,7 +850,7 @@ enforce_retract_first_layer = 0
 ensure_vertical_shell_thickness = 0
 exact_last_layer_height = 0
 external_infill_margin = 4
-external_perimeter_acceleration = 1000
+external_perimeter_acceleration = 750
 external_perimeter_cut_corners = 0%
 external_perimeter_extrusion_spacing = 
 external_perimeter_extrusion_width = 100%
@@ -874,7 +874,7 @@ fill_pattern = grid
 fill_smooth_distribution = 10%
 fill_smooth_width = 50%
 fill_top_flow_ratio = 100%
-first_layer_acceleration = 2000
+first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
 first_layer_extrusion_spacing = 
 first_layer_extrusion_width = 125%
@@ -889,7 +889,7 @@ first_layer_speed_over_raft = 30
 fuzzy_skin = none
 fuzzy_skin_point_dist = 200%
 fuzzy_skin_thickness = 150%
-gap_fill_acceleration = 2000
+gap_fill_acceleration = 1000
 gap_fill_enabled = 1
 gap_fill_flow_match_perimeter = 0%
 gap_fill_last = 1
@@ -900,12 +900,12 @@ gcode_comments = 0
 gcode_label_objects = 1
 gcode_resolution = 0
 gcode_substitutions = 
-hole_size_compensation = 0
+hole_size_compensation = 0.1
 hole_size_threshold = 100
 hole_to_polyhole = 0
 hole_to_polyhole_threshold = 0.01
 hole_to_polyhole_twisted = 1
-infill_acceleration = 7000
+infill_acceleration = 3500
 infill_anchor = 600%
 infill_anchor_max = 0
 infill_connection = connected
@@ -925,15 +925,15 @@ infill_speed = 300
 inherits = 
 interface_shells = 0
 ironing = 0
-ironing_acceleration = 2000
+ironing_acceleration = 1000
 ironing_angle = -1
 ironing_flowrate = 15%
 ironing_spacing = 0.1
 ironing_speed = 15
 ironing_type = top
 layer_height = 0.2
-max_print_speed = 300
-max_volumetric_speed = 15
+max_print_speed = 200
+max_volumetric_speed = 11
 milling_after_z = 200%
 milling_extra_size = 150%
 milling_post_process = 0
@@ -951,13 +951,13 @@ only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
 over_bridge_flow_ratio = 100%
-overhangs_acceleration = 2000
+overhangs_acceleration = 1000
 overhangs_reverse = 0
 overhangs_reverse_threshold = 250%
 overhangs_speed = 100%
 overhangs_width = 75%
 overhangs_width_speed = 0
-perimeter_acceleration = 2000
+perimeter_acceleration = 1000
 perimeter_bonding = 0%
 perimeter_extruder = 1
 perimeter_extrusion_spacing = 
@@ -973,7 +973,7 @@ print_custom_variables = wall_thickness_lines = 0
 print_extrusion_multiplier = 100%
 print_retract_length = -1
 print_retract_lift = -1
-print_settings_id = Ellis - PIF Standard (15mm3/s)
+print_settings_id = Ellis - PIF Standard (11mm3/s)
 print_temperature = 0
 raft_contact_distance = 0.1
 raft_expansion = 1.5
@@ -998,7 +998,7 @@ small_perimeter_max_length = 20
 small_perimeter_min_length = 6
 small_perimeter_speed = 30
 solid_fill_pattern = monotonic
-solid_infill_acceleration = 5000
+solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
@@ -1010,7 +1010,7 @@ solid_over_perimeters = 0
 spiral_vase = 0
 standby_temperature_delta = -5
 support_material = 0
-support_material_acceleration = 5000
+support_material_acceleration = 3500
 support_material_angle = 0
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
@@ -1022,7 +1022,7 @@ support_material_contact_distance_type = filament
 support_material_enforce_layers = 0
 support_material_extruder = 1
 support_material_extrusion_width = 0
-support_material_interface_acceleration = 5000
+support_material_interface_acceleration = 3500
 support_material_interface_contact_loops = 0
 support_material_interface_extruder = 1
 support_material_interface_layers = 2
@@ -1040,7 +1040,7 @@ support_material_xy_spacing = 75%
 thin_perimeters = 80%
 thin_perimeters_all = 20%
 thin_walls = 1
-thin_walls_acceleration = 2000
+thin_walls_acceleration = 750
 thin_walls_merge = 1
 thin_walls_min_width = 33%
 thin_walls_overlap = 50%
@@ -1049,13 +1049,13 @@ threads = 16
 top_fill_pattern = monotonicgapfill
 top_infill_extrusion_spacing = 
 top_infill_extrusion_width = 100%
-top_solid_infill_acceleration = 2000
+top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
 top_solid_min_thickness = 1
-travel_acceleration = 10000
+travel_acceleration = 3500
 travel_deceleration_use_target = 1
-travel_speed = 350
+travel_speed = 200
 travel_speed_z = 0
 wipe_tower = 0
 wipe_tower_bridging = 10
@@ -1417,7 +1417,7 @@ temperature = 250
 top_fan_speed = -1
 
 [filament:D3d PETG - Red]
-bed_temperature = 60
+bed_temperature = 70
 bridge_fan_speed = 100
 bridge_internal_fan_speed = -1
 chamber_temperature = 30
@@ -1489,7 +1489,7 @@ filament_wipe_inside_end = nil
 filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
-first_layer_bed_temperature = 60
+first_layer_bed_temperature = 70
 first_layer_temperature = 250
 full_fan_speed_layer = 4
 inherits = 
@@ -1500,7 +1500,7 @@ min_print_speed = 15
 slowdown_below_layer_time = 15
 start_filament_gcode = ""
 support_material_interface_fan_speed = -1
-temperature = 250
+temperature = 240
 top_fan_speed = -1
 
 [filament:D3d PETG - Silver]
@@ -1851,8 +1851,8 @@ support_material_interface_fan_speed = -1
 temperature = 235
 top_fan_speed = -1
 
-[filament:Nuolei TPU (Light Blue)]
-bed_temperature = 50
+[filament:Nuolei TPU - Light Blue]
+bed_temperature = 70
 bridge_fan_speed = 80
 bridge_internal_fan_speed = -1
 chamber_temperature = 0
@@ -1863,18 +1863,18 @@ compatible_prints_condition =
 disable_fan_first_layers = 3
 end_filament_gcode = "; Filament-specific end gcode"
 external_perimeter_fan_speed = -1
-extrusion_multiplier = 1.25
+extrusion_multiplier = 1
 fan_always_on = 0
 fan_below_layer_time = 100
-filament_colour = #008000
+filament_colour = #6FF2EC
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cooling_zone_pause = 0
-filament_cost = 40
+filament_cost = 18.07
 filament_custom_variables = ""
 filament_density = 1.22
-filament_deretract_speed = 25
+filament_deretract_speed = 30
 filament_diameter = 1.75
 filament_dip_extraction_speed = 70
 filament_dip_insertion_speed = 33
@@ -1894,18 +1894,18 @@ filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0|
 filament_retract_before_travel = nil
 filament_retract_before_wipe = nil
 filament_retract_layer_change = nil
-filament_retract_length = 0.28
+filament_retract_length = 0.3
 filament_retract_lift = nil
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
 filament_retract_restart_extra = nil
-filament_retract_speed = nil
+filament_retract_speed = 30
 filament_seam_gap = nil
 filament_settings_id = "Generic FLEX"
 filament_shrink = 100%
 filament_skinnydip_distance = 31
 filament_soluble = 0
-filament_spool_weight = 0
+filament_spool_weight = 500
 filament_toolchange_delay = 0
 filament_toolchange_part_fan_speed = 50
 filament_toolchange_temp = 200
@@ -1916,7 +1916,7 @@ filament_unloading_speed_start = 100
 filament_use_fast_skinnydip = 0
 filament_use_skinnydip = 0
 filament_vendor = Generic
-filament_wipe = 0
+filament_wipe = nil
 filament_wipe_advanced_pigment = 0.5
 filament_wipe_extra_perimeter = nil
 filament_wipe_inside_depth = nil
@@ -1924,8 +1924,8 @@ filament_wipe_inside_end = nil
 filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
-first_layer_bed_temperature = 50
-first_layer_temperature = 225
+first_layer_bed_temperature = 70
+first_layer_temperature = 235
 full_fan_speed_layer = 0
 inherits = 
 max_fan_speed = 90
@@ -1935,11 +1935,11 @@ min_print_speed = 15
 slowdown_below_layer_time = 15
 start_filament_gcode = "M900 K0"
 support_material_interface_fan_speed = -1
-temperature = 225
+temperature = 235
 top_fan_speed = -1
 
 [filament:Sparta3D ABS @VORON - Sky Blue, Sparkle]
-bed_temperature = 80
+bed_temperature = 100
 bridge_fan_speed = 100
 bridge_internal_fan_speed = -1
 chamber_temperature = 50
@@ -1953,7 +1953,7 @@ external_perimeter_fan_speed = -1
 extrusion_multiplier = 0.98
 fan_always_on = 0
 fan_below_layer_time = 20
-filament_colour = #3095E4
+filament_colour = #4BC1DB
 filament_cooling_final_speed = 3.4
 filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
@@ -2011,7 +2011,7 @@ filament_wipe_inside_end = nil
 filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
-first_layer_bed_temperature = 80
+first_layer_bed_temperature = 100
 first_layer_temperature = 250
 full_fan_speed_layer = 4
 inherits = 
@@ -2026,7 +2026,7 @@ temperature = 240
 top_fan_speed = -1
 
 [filament:eSun ABS @VORON - Black]
-bed_temperature = 90
+bed_temperature = 100
 bridge_fan_speed = 100
 bridge_internal_fan_speed = -1
 chamber_temperature = 50
@@ -2199,8 +2199,95 @@ support_material_interface_fan_speed = -1
 temperature = 245
 top_fan_speed = -1
 
+[filament:eSun PLA+ Blue]
+bed_temperature = 60
+bridge_fan_speed = 100
+bridge_internal_fan_speed = -1
+chamber_temperature = 0
+compatible_printers = 
+compatible_printers_condition = 
+compatible_prints = 
+compatible_prints_condition = 
+disable_fan_first_layers = 1
+end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
+external_perimeter_fan_speed = -1
+extrusion_multiplier = 1
+fan_always_on = 1
+fan_below_layer_time = 20
+filament_colour = #0E5FED
+filament_cooling_final_speed = 3.4
+filament_cooling_initial_speed = 2.2
+filament_cooling_moves = 0
+filament_cooling_zone_pause = 0
+filament_cost = 19.35
+filament_custom_variables = ""
+filament_density = 1.23
+filament_deretract_speed = nil
+filament_diameter = 1.75
+filament_dip_extraction_speed = 70
+filament_dip_insertion_speed = 33
+filament_enable_toolchange_part_fan = 0
+filament_enable_toolchange_temp = 0
+filament_load_time = 0
+filament_loading_speed = 28
+filament_loading_speed_start = 3
+filament_max_overlap = 100%
+filament_max_speed = 0
+filament_max_volumetric_speed = 0
+filament_max_wipe_tower_speed = 0
+filament_melt_zone_pause = 0
+filament_minimal_purge_on_wipe_tower = 15
+filament_notes = ";Full spool weight: 1280g"
+filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0| 0.05 6.6 0.45 6.8 0.95 7.8 1.45 8.3 1.95 9.7 2.45 10 2.95 7.6 3.45 7.6 3.95 7.6 4.45 7.6 4.95 7.6"
+filament_retract_before_travel = nil
+filament_retract_before_wipe = nil
+filament_retract_layer_change = nil
+filament_retract_length = nil
+filament_retract_lift = nil
+filament_retract_lift_above = nil
+filament_retract_lift_below = nil
+filament_retract_restart_extra = nil
+filament_retract_speed = nil
+filament_seam_gap = nil
+filament_settings_id = "ABS - KVP"
+filament_shrink = 100%
+filament_skinnydip_distance = 31
+filament_soluble = 0
+filament_spool_weight = 1000
+filament_toolchange_delay = 0
+filament_toolchange_part_fan_speed = 50
+filament_toolchange_temp = 200
+filament_type = PLA
+filament_unload_time = 0
+filament_unloading_speed = 90
+filament_unloading_speed_start = 100
+filament_use_fast_skinnydip = 0
+filament_use_skinnydip = 0
+filament_vendor = (Unknown)
+filament_wipe = nil
+filament_wipe_advanced_pigment = 0.5
+filament_wipe_extra_perimeter = nil
+filament_wipe_inside_depth = nil
+filament_wipe_inside_end = nil
+filament_wipe_inside_start = nil
+filament_wipe_only_crossing = nil
+filament_wipe_speed = nil
+first_layer_bed_temperature = 60
+first_layer_temperature = 210
+full_fan_speed_layer = 4
+inherits = 
+max_fan_speed = 100
+max_speed_reduction = 90%
+min_fan_speed = 100
+min_print_speed = 10
+slowdown_below_layer_time = 15
+start_filament_gcode = "; Filament gcode\n"
+support_material_interface_fan_speed = -1
+temperature = 210
+top_fan_speed = -1
+
 [filament:eSun PLA+ Magenta]
-bed_temperature = 40
+bed_temperature = 60
 bridge_fan_speed = 100
 bridge_internal_fan_speed = -1
 chamber_temperature = 0
@@ -2272,7 +2359,7 @@ filament_wipe_inside_end = nil
 filament_wipe_inside_start = nil
 filament_wipe_only_crossing = nil
 filament_wipe_speed = nil
-first_layer_bed_temperature = 40
+first_layer_bed_temperature = 60
 first_layer_temperature = 210
 full_fan_speed_layer = 4
 inherits = 
@@ -2366,7 +2453,7 @@ retract_before_travel = 2
 retract_before_wipe = 0%
 retract_layer_change = 1
 retract_length = 0.3
-retract_length_toolchange = 4
+retract_length_toolchange = 10
 retract_lift = 0
 retract_lift_above = 0.2
 retract_lift_below = 250
@@ -2378,7 +2465,7 @@ retract_speed = 60
 seam_gap = 15%
 silent_mode = 0
 single_extruder_multi_material = 0
-start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]}\r\nPURGE_LINE\n\n;; If you are passing variables to PRINT_START, comment out above line and uncomment the last 3 lines instead. (I already did this)\n;; Guide: https://github.com/AndrewEllis93/Print-Tuning-Guide/blob/main/articles/passing_slicer_variables.md\n;; Make sure the variable names match (for example if you use "EXTRUDER" instead of "HOTEND")\n
+start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} CHAMBER=[chamber_temperature]\r\nPURGE_LINE\n\n;; If you are passing variables to PRINT_START, comment out above line and uncomment the last 3 lines instead. (I already did this)\n;; Guide: https://github.com/AndrewEllis93/Print-Tuning-Guide/blob/main/articles/passing_slicer_variables.md\n;; Make sure the variable names match (for example if you use "EXTRUDER" instead of "HOTEND")\n
 start_gcode_manual = 0
 template_custom_gcode = 
 thumbnails = 32x32,400x300
@@ -2412,9 +2499,8 @@ z_offset = 0
 z_step = 0.005
 
 [presets]
-print = Ellis_PIF_Standard_15mm3
+print = _Ellis_PIF_45_Degree_11mm3-SOVOL
 sla_print = 
 sla_material = 
 printer = Sovol Sv06
-filament = eSun PLA+ Magenta
-physical_printer = Sv06
+filament = eSun PLA+ Blue