diff --git a/README.md b/README.md
index 60ea68a..c279e13 100644
--- a/README.md
+++ b/README.md
@@ -1,7 +1,48 @@
 # 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration 🏎️
 
-## This branch contains a Klipper configuration that is NOT ready for use.
+## This branch contains the Klipper configuration and firmware for the Sovol SV06 3D printer with the `BTT SKR-Mini-E3-V3.0` motherboard.
 
-## ❗☠️ YOU HAVE BEEN WARNED ☠️❗
+## If you were looking for my OSS Klipper Configuration for the Sovol SV06 with *completely stock hardware*, please refer to the [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch.
 
-## Please refer to the [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch to download the recommended Klipper configuration for the Sovol SV06 with stock hardware.
\ No newline at end of file
+I am creating these files for my personal use and cannot be held responsible for what it might do to your printer.
+
+## ❗☠️ I do not own this board so everything found on this branch is COMPLETELY UNTESTED ☠️❗
+## ❗☠️ USE AT YOUR OWN RISK. YOU HAVE BEEN WARNED. ☠️❗
+
+## An Important Note
+
+⭐ A big thank you to Github user `transistor1`. This branch would not have been possible without his help. Please checkout his profile [here](https://github.com/transistor1). ⭐
+
+## Installation Instructions
+
+### Electronic Wiring
+
+Wire cables according to the following diagram:
+<img src="./misc/skr-mini/skr-mini-e3-v3.0-v1678580296384.png" alt='skr-mini-e3-v3.0 installation instructions'/>
+### Download Firmware Precompiled by BIGTREETECH
+- [firmware-USB.bin](./misc/skr-mini/firmware-USB.bin). Connect the SKR-Mini to the Raspberry Pi via USB connection.
+- [firmware-USART2.bin](./misc/skr-mini/firmware-USART2.bin). Use TFT port USART2 to communicate with raspberry pi. Connect the UART-TX of raspberry pi with the USART-RX2 of motherboard and connect the UART-RX of raspberry pi with the USART-TX2 of motherboard directly to communicate normally.
+
+Alternatively, find instructions on how to build the firmware yourself [here](https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#build-firmware-image).
+
+### Flash Firmware
+
+1. Rename `firmware-USB.bin` or `firmware-USART2.bin` to `firmware.bin`.
+Important: If the file is not renamed, the bootloader will not be updated properly.
+2. Copy `firmware.bin` to the root directory of the microSD card (make sure the card is in FAT32 format).
+3. Power off the SKR-mini-E3-V3.0.
+4. Insert the microSD card.
+5. Power on the SKR-mini-E3-V3.0.
+6. After a few seconds, the SKR-mini-E3-V3.0 should be flashed.
+7. You can confirm that the flash was successful, by running ls /dev/serial/by-id. If the flash was successful, you'll see something like the following:
+<img src="./misc/skr-mini/ls-output.png" alt='ls output'/>
+
+### Download Klipper Configuration
+
+Follow the instructions found in the [Download Klipper Configuration](https://github.com/bassamanator/Sovol-SV06-firmware#download-klipper-configuration) section and onwards.
+
+# Sources
+
+- https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#how-to-use-klipper-on-skr-mini-e3-v30
+- https://forum.sovol3d.com/t/sv06-mit-skr-e3-mini-v3/1189/24
+- https://github.com/bassamanator/everything-sovol-sv06/discussions/14
\ No newline at end of file
diff --git a/misc/skr-mini/README.md b/misc/skr-mini/README.md
index 242582b..61bd059 100644
--- a/misc/skr-mini/README.md
+++ b/misc/skr-mini/README.md
@@ -25,3 +25,4 @@ Important: If the file is not renamed, the bootloader will not be updated proper
 # Sources
 
 - https://github.com/bigtreetech/BIGTREETECH-SKR-mini-E3/tree/master/firmware/V3.0/Klipper#how-to-use-klipper-on-skr-mini-e3-v30
+- https://forum.sovol3d.com/t/sv06-mit-skr-e3-mini-v3/1189/24