diff --git a/README.md b/README.md index 5851b0a..60ea68a 100644 --- a/README.md +++ b/README.md @@ -1,175 +1,7 @@ -# 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration +# 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration 🏎️ -This repository contains the Klipper configuration and firmware for the Sovol SV06 3D printer. +## This branch contains a Klipper configuration that is NOT ready for use. -I am creating these files for my personal use and cannot be held responsible for what it might do to your printer. +## ❗☠️ YOU HAVE BEEN WARNED ☠️❗ -❗☠️ **USE AT YOUR OWN RISK. YOU HAVE BEEN WARNED.** ☠️❗ - -# Highlights - -- 💥 This Klipper configuration is an *endpoint*, meaning that it contains **everything** that you could possibly need in order to have an excellent Klipper experience! 💥 -- Minimum configuration settings for Mainsail/Fluiddpi to work. -- SuperSlicer config bundle that contains the printer configuration, as well as what are considered by many to be the best print settings available for any FDM printer ([Ellis' SuperSlicer Profiles](https://github.com/AndrewEllis93/Ellis-SuperSlicer-Profiles)). Find the differences between the different print setting profiles [here](https://github.com/AndrewEllis93/Ellis-SuperSlicer-Profiles/tree/master/SuperSlicer). But basically, the 45 degree profile places the seam at the back. -- Bed model and texture to use in SuperSlicer/PrusaSlicer. -- Macros - - **Improved** mechanical gantry calibration/`G34` macro that provides the user audio feedback, and time to check the calibration. - - Misc macros: `PRINT_START`, `CANCEL_PRINT`, `PRINT_END`, `PAUSE`, `RESUME`. - - Parking macros (parks the printhead at various locations): `PARKFRONT`, `PARKFRONTLOW`, `PARKREAR`, `PARKCENTER`, `PARKBED`. - - Load/unload filament macros. - - Purge line macro. - -To do: - -- [ ] Replace M109/M190 with `TEMPERATURE_WAIT`. -- [ ] Get the Ellis `TEST_SPEED` macro working. -- [x] Add information about directory structure. -- [ ] Create FAQ section. -- [ ] Finalize filament sensor config and merge into `master`. -- [ ] Create topic in Discussion section detailing how users should keep track of their own Klipper config using `git`. - -## Stay Up-to-Date - -I work on this repository all the time and a lot of new features are coming. Watch releases of this repository to be notified for future updates: - -Raspberry Pi - -# Installation Steps - -## Before You Begin - -- Know what you're getting into by reading this documentation *fully!* -- There is an assumption that you are connected to your host Raspberry Pi via SSH, and that your printer motherboard is connected to the host via USB. -- Klipper *must* be installed on the host Raspberry Pi for everything to work. Easiest is to use a [FluiddPi](https://docs.fluidd.xyz/installation/fluiddpi#download) or [MainsailOS](https://github.com/mainsail-crew/mainsail/releases/latest) image. -- Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section. -- If you see any errors, or encounter any issues, please create an [Issue](https://github.com/bassamanator/Sovol-SV06-firmware/issues/new), or a [Pull request](https://github.com/bassamanator/Sovol-SV06-firmware/pulls). -- I would recommend searching for the word `NOTE` in this repository. There are roughly half a dozen short points amongst the various files that you should be aware of if you're using this configuration. - -## Flash Firmware - -💡 *If you have already flashed klipper onto your motherboard in the past, you can skip this step* - -1. Copy `klipper.bin` to a MicroSD card and rename to `anyNewFilename.bin`. -2. Make sure the printer is off. -3. Insert MicroSD into printer. -4. Turn on the printer and wait a minute (usually takes 10 seconds). -5. Turn off printer and remove MicroSD. - -You may find this [video](https://youtu.be/p6l253OJa34) useful. - -⚠️ **Caveat**: Flashing will only work if current firmware filename (`anyNewFilename.bin` in this example) is different from previous flashing procedure. The `.bin` is also important. - -## Download Klipper Configuration - -You can choose *either* of the 2 following methods. - -### Clone the Repository - -1. `cd ~/printer_data/config` -2. Empty entire `~/printer_data/config` folder. Unfortunately, for safety reasons I will not post this command here. However, in linux, you can delete files via `rm filename`. -3. `git clone -b master --single-branch git@github.com:bassamanator/Sovol-SV06-firmware.git .` - -### Download the ZIP - -1. [Download](https://github.com/bassamanator/Sovol-SV06-firmware/archive/refs/heads/master.zip) the `ZIP` file containing the Klipper configuration. -2. The parent folder in the `ZIP` is `Sovol-SV06-firmware-master`. This is relevant in the next step. -3. Extract **only** the *contents* of the parent folder into `~/printer_data/config`. - -## Initial Steps - -### Step 1 - -1. Find what port the `mcu` (SV06 motherboard) is connected to via `ls -l /dev/serial/by-id/`. -2. Adjust the `[mcu]` section in `printer.cfg` accordingly. - -### Step 2 - -❗☠️ **Your finger should be on the power switch for most of these steps** ☠️❗ - -❗☠️ **Power off if there is a collision/problem** ☠️❗ - -💡 I recommend no filament be loaded for any of these steps. - -1. Do a `G28`; home all. - 1. Check to see if `X` and `Y` max positions (`G1 X223 F3000`, `G1 Y223 F3000`) can be reached, and adjust `position_max`, if necessary. You can probably go all the way up to `225` for `X` and `Y` both, however, I would not recommend it. -2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up agaisnt the `stoppers` at the top. You will hear a succession of beeps. - 1. Figure out your `Z` `position_max` by baby stepping your way up to the beam. The range is 250 to 261 from what I've seen, could be even higher for you. Adjust `position_max`, if necessary. I can go all the way to 258 over and over again, however, I would not print anything higher than 255 probably. -3. Pid tune the bed, but first move the printhead to the center. Ideally, all Pid tuning should occur at the temperatures that you print most at. - 1. `G28` - 2. `G1 X111 Y111 Z40 F6000` - 3. `PID_CALIBRATE HEATER=heater_bed TARGET=70` - 4. `SAVE_CONFIG` (once completed) -4. Pid tune the extruder while part cooling fan runs at 25%. - 1. `G28` - 2. `G1 X111 Y111 Z10 F6000` - 3. `M106 S64` - 4. `PID_CALIBRATE HEATER=extruder TARGET=245` - 5. `SAVE_CONFIG` (once completed) -5. Adjust `z_offset`. Make sure your nozzle if very clean. Paper test [reference](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test). - 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` - 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` - 3. Proceed to next steps after both temperatures have been reached. - 4. `G28` - 5. `PROBE_CALIBRATE` - 6. `SAVE_CONFIG` (once completed) -6. Create a bed mesh. - 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` - 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` - 3. Proceed to next steps after both temperatures have been reached. - 4. `G28` - 5. `BED_MESH_CALIBRATE` - 6. `SAVE_CONFIG` (once completed) - -## Directory Structure - -This repository contains many files and folders. Some are *necessary* for this Klipper configuration to work, others are not. -- **Necessary** items are marked with a ✅. -- Items that can *optionally* be deleted are marked with a ❌. - -``` -├── cfgs ✅ -│   ├── adxl-direct.cfg -│   ├── adxl-rp2040.cfg -│   ├── beeper.cfg -│   ├── macros.cfg -│   ├── MECHANICAL_GANTRY_CALIBRATION.cfg -│   ├── PARKING.cfg -│   └── TEST_SPEED.cfg [☠️Not ready for use☠️] -├── images ❌ -│   └── githubstar.gif -├── misc ❌ -│   ├── cup-border.png -│   ├── klipper.bin -│   ├── logo_white_stroke.png -│   ├── M503-output.yml -│   ├── SuperSlicer_config_bundle.ini -│   ├── sv06-buildPlate.png -│   ├── SV06-buildPlate.stl -│   └── SV06-texture.svg -├── moonraker.conf ✅ -├── printer.cfg ✅ -└── README.md ❌ -``` - -## Ko-fi Support Me Ko-fi - -If you found my work useful, please consider buying me a [Ko-fi](https://ko-fi.com/bassamanator). - -## Useful Resources - -- [Everything Sovol SV06](https://github.com/bassamanator/everything-sovol-sv06) -- [RP2040-Zero ADXL345 Connection Klipper](https://github.com/bassamanator/rp2040-zero-adxl345-klipper) -- ⭐⭐⭐ [Ellis' Print Tuning Guide](https://ellis3dp.com/Print-Tuning-Guide) - -## Sources - -- https://www.klipper3d.org -- https://ellis3dp.com/Print-Tuning-Guide -- https://github.com/strayr/strayr-k-macros -- https://docs.vorondesign.com/build/software/miniE3_v20_klipper.html -- ⭐ https://github.com/spinixguy/Sovol-SV06-firmware -- https://github.com/Pr20100/SOVOL-SV06-Klipper-profile -- https://www.printables.com/model/378915-sovol-sv06-buildplate-texture-and-model-for-prusas -- https://github.com/AndrewEllis93/Ellis-SuperSlicer-Profiles - -[![ko-fi](https://ko-fi.com/img/githubbutton_sm.svg)](https://ko-fi.com/H2H0HIHTH) +## Please refer to the [master](https://github.com/bassamanator/Sovol-SV06-firmware/tree/master) branch to download the recommended Klipper configuration for the Sovol SV06 with stock hardware. \ No newline at end of file diff --git a/cfgs/macros.cfg b/cfgs/macros.cfg index 7962d60..f762c09 100644 --- a/cfgs/macros.cfg +++ b/cfgs/macros.cfg @@ -13,6 +13,28 @@ gcode: {action_raise_error('Pre purge prime length not found')} {% endif %} +[gcode_macro M109] +rename_existing: M99109 +gcode: + #Parameters + {% set s = params.S|float %} + + M104 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %} ; Set hotend temp + {% if s != 0 %} + TEMPERATURE_WAIT SENSOR=extruder MINIMUM={s} MAXIMUM={s+1} ; Wait for hotend temp (within 1 degree) + {% endif %} + +[gcode_macro M190] +rename_existing: M99190 +gcode: + #Parameters + {% set s = params.S|float %} + + M140 {% for p in params %}{'%s%s' % (p, params[p])}{% endfor %} ; Set bed temp + {% if s != 0 %} + TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={s} MAXIMUM={s+1} ; Wait for bed temp (within 1 degree) + {% endif %} + [gcode_macro PURGE_LINE] # https://github.com/JoeCat1207/V0.1-Purge-line-SuperSlicer/blob/main/Purgeline.txt # https://github.com/VoronDesign/Voron-Switchwire/blob/200cdae033c59ef81f67c4235469da7ca66d53a1/Firmware/skr_mini_e3_v2_config.cfg