diff --git a/printer.cfg b/printer.cfg
index d9ce932..951ebf1 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -96,7 +96,7 @@ diag_pin: PA7
 step_pin: PB4
 dir_pin: !PB3
 enable_pin: !PC3
-microsteps: 256
+microsteps: 128
 rotation_distance: 4.65 # NOTE Calibrate e-steps and adjust https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 filament_diameter: 1.750
@@ -182,9 +182,9 @@ encoder_pins: ^PB14, ^PB10
 click_pin: ^!PB2
 
 [input_shaper]
-shaper_freq_x: 55.0 # 97.2 # 82.2 # 84.2; 4020
+shaper_freq_x: 56.6 # 55.0 # 97.2 # 82.2 # 84.2; 4020
 shaper_type_x: mzv # 3hump_ei # 2hump_ei
-shaper_freq_y: 40.6 # 41.8; 4020
+shaper_freq_y: 48.4 # 40.6 # 41.8; 4020
 shaper_type_y: mzv
 
 [bed_screws]
@@ -245,7 +245,7 @@ runout_gcode:
 #*# pid_kd = 928.332
 #*#
 #*# [probe]
-#*# z_offset = 1.285
+#*# z_offset = 1.340
 #*#
 #*# [bed_mesh personalPreEdit]
 #*# version = 1
@@ -271,26 +271,7 @@ runout_gcode:
 #*# compensation_start_x = 27.0
 #*# compensation_end_x = 195.0
 #*#
-#*# [bed_mesh default-preXTwist-fix]
-#*# version = 1
-#*# points =
-#*# 	-0.150000, -0.110000, -0.110000, -0.130000, -0.130000
-#*# 	-0.165000, -0.130000, -0.130000, -0.130000, -0.130000
-#*# 	-0.165000, -0.112266, -0.110000, -0.130000, -0.130000
-#*# 	-0.160000, -0.105430, -0.110000, -0.130000, -0.130000
-#*# 	-0.120000, -0.071211, -0.091407, -0.110000, -0.110000
-#*# min_x = 27.0
-#*# max_x = 222.0
-#*# min_y = 5.0
-#*# max_y = 203.0
-#*# x_count = 5
-#*# y_count = 5
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*#
-#*# [bed_mesh default]
+#*# [bed_mesh default-preNewNozzle]
 #*# version = 1
 #*# points =
 #*# 	-0.038051, -0.033174, -0.038453, -0.061829, -0.123230
@@ -298,6 +279,25 @@ runout_gcode:
 #*# 	-0.108832, -0.063955, -0.058921, -0.063704, -0.125261
 #*# 	-0.123363, -0.074580, -0.063296, -0.081360, -0.140261
 #*# 	-0.074145, -0.020830, -0.011578, -0.024954, -0.074948
+#*# min_x = 27.0
+#*# max_x = 222.0
+#*# min_y = 6.0
+#*# max_y = 203.0
+#*# x_count = 5
+#*# y_count = 5
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = lagrange
+#*# tension = 0.2
+#*#
+#*# [bed_mesh default]
+#*# version = 1
+#*# points =
+#*# 	  0.046941, 0.011027, -0.033169, -0.071035, -0.133125
+#*# 	  0.003660, -0.031630, -0.060669, -0.092285, -0.159844
+#*# 	  -0.032121, -0.035848, -0.066919, -0.097129, -0.162188
+#*# 	  -0.047121, -0.044598, -0.058951, -0.102910, -0.155000
+#*# 	  0.004597, 0.011964, -0.007232, -0.042910, -0.085938
 #*# x_count = 5
 #*# y_count = 5
 #*# mesh_x_pps = 2