From 6e378941347ce1fb9b8b6abfbf234187609d738c Mon Sep 17 00:00:00 2001 From: Bassam Husain Date: Fri, 1 Dec 2023 13:54:36 -0500 Subject: [PATCH] Adjust config bundles: add SV07. --- ...usaSlicer_config_bundle-SV06-SV07-All.ini} | 560 +++++++++++++++++- ...perSlicer_config_bundle-SV06-SV07-All.ini} | 490 +++++++++++---- 2 files changed, 937 insertions(+), 113 deletions(-) rename misc/{PrusaSlicer_config_bundle-SV06-Both.ini => PrusaSlicer_config_bundle-SV06-SV07-All.ini} (83%) rename misc/{SuperSlicer_config_bundle-SV06-Both.ini => SuperSlicer_config_bundle-SV06-SV07-All.ini} (90%) diff --git a/misc/PrusaSlicer_config_bundle-SV06-Both.ini b/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini similarity index 83% rename from misc/PrusaSlicer_config_bundle-SV06-Both.ini rename to misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini index ce24ab9..567f20f 100644 --- a/misc/PrusaSlicer_config_bundle-SV06-Both.ini +++ b/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini @@ -1,4 +1,4 @@ -# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2023-11-23 at 18:53:35 UTC +# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2023-12-01 at 18:05:53 UTC [print:0.20mm QUALITY SV06 Ellis] avoid_crossing_curled_overhangs = 0 @@ -708,6 +708,183 @@ wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 +[print:_Ellis_Decorative_Standard_24mm3_CoreXY-Speeds] +avoid_crossing_curled_overhangs = 0 +avoid_crossing_perimeters = 0 +avoid_crossing_perimeters_max_detour = 0 +bottom_fill_pattern = monotoniclines +bottom_solid_layers = 3 +bottom_solid_min_thickness = 0.6 +bridge_acceleration = 5000 +bridge_angle = 0 +bridge_flow_ratio = 0.85 +bridge_speed = 140 +brim_separation = 0 +brim_type = outer_only +brim_width = 0 +compatible_printers = +compatible_printers_condition = +complete_objects = 0 +default_acceleration = 4000 +dont_support_bridges = 1 +draft_shield = disabled +elefant_foot_compensation = 0 +enable_dynamic_overhang_speeds = 0 +external_perimeter_acceleration = 1000 +external_perimeter_extrusion_width = 0.4 +external_perimeter_speed = 80 +external_perimeters_first = 0 +extra_perimeters = 0 +extra_perimeters_on_overhangs = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extrusion_width = 0.46 +fill_angle = 45 +fill_density = 10% +fill_pattern = monotonic +first_layer_acceleration = 2000 +first_layer_acceleration_over_raft = 0 +first_layer_extrusion_width = 0.5 +first_layer_height = 0.26 +first_layer_speed = 30 +first_layer_speed_over_raft = 30 +fuzzy_skin = none +fuzzy_skin_point_dist = 0.8 +fuzzy_skin_thickness = 0.3 +gap_fill_enabled = 1 +gap_fill_speed = 30 +gcode_comments = 0 +gcode_label_objects = 1 +gcode_resolution = 0 +gcode_substitutions = +infill_acceleration = 7000 +infill_anchor = 600% +infill_anchor_max = 400% +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 0.46 +infill_first = 0 +infill_overlap = 25% +infill_speed = 300 +inherits = +interface_shells = 0 +ironing = 0 +ironing_flowrate = 15% +ironing_spacing = 0.1 +ironing_speed = 15 +ironing_type = top +layer_height = 0.2 +max_print_speed = 300 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 +max_volumetric_speed = 24 +min_bead_width = 85% +min_feature_size = 25% +min_skirt_length = 20 +mmu_segmented_region_interlocking_depth = 0 +mmu_segmented_region_max_width = 0 +notes = +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode +overhang_speed_0 = 75% +overhang_speed_1 = 80% +overhang_speed_2 = 90% +overhang_speed_3 = 100% +overhangs = 1 +perimeter_acceleration = 2000 +perimeter_extruder = 1 +perimeter_extrusion_width = 0.46 +perimeter_generator = arachne +perimeter_speed = 150 +perimeters = 3 +post_process = +print_settings_id = Ellis - Decorative Standard (15mm³) +raft_contact_distance = 0.1 +raft_expansion = 1.5 +raft_first_layer_density = 90% +raft_first_layer_expansion = 3 +raft_layers = 0 +resolution = 0.0125 +seam_position = aligned +single_extruder_multi_material_priming = 1 +skirt_distance = 3 +skirt_height = 1 +skirts = 1 +slice_closing_radius = 0.049 +slicing_mode = regular +small_perimeter_speed = 30 +solid_infill_acceleration = 5000 +solid_infill_below_area = 0 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 0.56 +solid_infill_speed = 200 +spiral_vase = 0 +staggered_inner_seams = 0 +standby_temperature_delta = -5 +support_material = 1 +support_material_angle = 0 +support_material_auto = 1 +support_material_bottom_contact_distance = 0 +support_material_bottom_interface_layers = -1 +support_material_buildplate_only = 1 +support_material_closing_radius = 2 +support_material_contact_distance = 0.1 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 2 +support_material_interface_pattern = rectilinear +support_material_interface_spacing = 0.2 +support_material_interface_speed = 100 +support_material_pattern = rectilinear +support_material_spacing = 3 +support_material_speed = 120 +support_material_style = organic +support_material_synchronize_layers = 0 +support_material_threshold = 30 +support_material_with_sheath = 0 +support_material_xy_spacing = 75% +support_tree_angle = 40 +support_tree_angle_slow = 25 +support_tree_branch_diameter = 2 +support_tree_branch_diameter_angle = 5 +support_tree_branch_diameter_double_wall = 3 +support_tree_branch_distance = 1 +support_tree_tip_diameter = 0.8 +support_tree_top_rate = 30% +thick_bridges = 0 +thin_walls = 1 +threads = 16 +top_fill_pattern = monotoniclines +top_infill_extrusion_width = 0.4 +top_solid_infill_acceleration = 2000 +top_solid_infill_speed = 60 +top_solid_layers = 5 +top_solid_min_thickness = 1 +travel_acceleration = 10000 +travel_speed = 300 +travel_speed_z = 0 +wall_distribution_count = 1 +wall_transition_angle = 10 +wall_transition_filter_deviation = 25% +wall_transition_length = 100% +wipe_tower = 0 +wipe_tower_bridging = 10 +wipe_tower_brim_width = 2 +wipe_tower_cone_angle = 0 +wipe_tower_extra_spacing = 100% +wipe_tower_extruder = 0 +wipe_tower_no_sparse_layers = 0 +wipe_tower_rotation_angle = 0 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 +xy_size_compensation = 0 + [print:_Ellis_PIF_Standard_15mm3_CoreXY-Speeds] avoid_crossing_curled_overhangs = 0 avoid_crossing_perimeters = 0 @@ -885,6 +1062,183 @@ wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 +[print:_Ellis_PIF_Standard_24mm3_CoreXY-Speeds] +avoid_crossing_curled_overhangs = 0 +avoid_crossing_perimeters = 0 +avoid_crossing_perimeters_max_detour = 0 +bottom_fill_pattern = monotoniclines +bottom_solid_layers = 5 +bottom_solid_min_thickness = 1 +bridge_acceleration = 5000 +bridge_angle = 0 +bridge_flow_ratio = 0.85 +bridge_speed = 140 +brim_separation = 0 +brim_type = outer_only +brim_width = 0 +compatible_printers = +compatible_printers_condition = +complete_objects = 0 +default_acceleration = 4000 +dont_support_bridges = 1 +draft_shield = disabled +elefant_foot_compensation = 0 +enable_dynamic_overhang_speeds = 0 +external_perimeter_acceleration = 1000 +external_perimeter_extrusion_width = 0.4 +external_perimeter_speed = 80 +external_perimeters_first = 0 +extra_perimeters = 0 +extra_perimeters_on_overhangs = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extrusion_width = 0.46 +fill_angle = 45 +fill_density = 40% +fill_pattern = grid +first_layer_acceleration = 2000 +first_layer_acceleration_over_raft = 0 +first_layer_extrusion_width = 0.5 +first_layer_height = 0.26 +first_layer_speed = 30 +first_layer_speed_over_raft = 30 +fuzzy_skin = none +fuzzy_skin_point_dist = 0.8 +fuzzy_skin_thickness = 0.3 +gap_fill_enabled = 1 +gap_fill_speed = 30 +gcode_comments = 0 +gcode_label_objects = 1 +gcode_resolution = 0 +gcode_substitutions = +infill_acceleration = 7000 +infill_anchor = 600% +infill_anchor_max = 400% +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 0.64 +infill_first = 0 +infill_overlap = 25% +infill_speed = 300 +inherits = +interface_shells = 0 +ironing = 0 +ironing_flowrate = 15% +ironing_spacing = 0.1 +ironing_speed = 15 +ironing_type = top +layer_height = 0.2 +max_print_speed = 300 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 +max_volumetric_speed = 24 +min_bead_width = 85% +min_feature_size = 25% +min_skirt_length = 20 +mmu_segmented_region_interlocking_depth = 0 +mmu_segmented_region_max_width = 0 +notes = +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode +overhang_speed_0 = 75% +overhang_speed_1 = 80% +overhang_speed_2 = 90% +overhang_speed_3 = 100% +overhangs = 1 +perimeter_acceleration = 2000 +perimeter_extruder = 1 +perimeter_extrusion_width = 0.4 +perimeter_generator = arachne +perimeter_speed = 150 +perimeters = 4 +post_process = +print_settings_id = Ellis - PIF Standard (15mm³) +raft_contact_distance = 0.1 +raft_expansion = 1.5 +raft_first_layer_density = 90% +raft_first_layer_expansion = 3 +raft_layers = 0 +resolution = 0.0125 +seam_position = aligned +single_extruder_multi_material_priming = 1 +skirt_distance = 3 +skirt_height = 1 +skirts = 1 +slice_closing_radius = 0.049 +slicing_mode = regular +small_perimeter_speed = 30 +solid_infill_acceleration = 5000 +solid_infill_below_area = 0 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 0.56 +solid_infill_speed = 200 +spiral_vase = 0 +staggered_inner_seams = 0 +standby_temperature_delta = -5 +support_material = 0 +support_material_angle = 0 +support_material_auto = 1 +support_material_bottom_contact_distance = 0 +support_material_bottom_interface_layers = -1 +support_material_buildplate_only = 1 +support_material_closing_radius = 2 +support_material_contact_distance = 0.1 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 2 +support_material_interface_pattern = rectilinear +support_material_interface_spacing = 0.2 +support_material_interface_speed = 100 +support_material_pattern = rectilinear +support_material_spacing = 3 +support_material_speed = 120 +support_material_style = organic +support_material_synchronize_layers = 0 +support_material_threshold = 30 +support_material_with_sheath = 0 +support_material_xy_spacing = 75% +support_tree_angle = 40 +support_tree_angle_slow = 25 +support_tree_branch_diameter = 2 +support_tree_branch_diameter_angle = 5 +support_tree_branch_diameter_double_wall = 3 +support_tree_branch_distance = 1 +support_tree_tip_diameter = 0.8 +support_tree_top_rate = 30% +thick_bridges = 0 +thin_walls = 1 +threads = 16 +top_fill_pattern = monotoniclines +top_infill_extrusion_width = 0.4 +top_solid_infill_acceleration = 2000 +top_solid_infill_speed = 60 +top_solid_layers = 5 +top_solid_min_thickness = 1 +travel_acceleration = 10000 +travel_speed = 300 +travel_speed_z = 0 +wall_distribution_count = 1 +wall_transition_angle = 10 +wall_transition_filter_deviation = 25% +wall_transition_length = 100% +wipe_tower = 0 +wipe_tower_bridging = 10 +wipe_tower_brim_width = 2 +wipe_tower_cone_angle = 0 +wipe_tower_extra_spacing = 100% +wipe_tower_extruder = 0 +wipe_tower_no_sparse_layers = 0 +wipe_tower_rotation_angle = 0 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 +xy_size_compensation = 0 + [filament:Basic PETG] bed_temperature = 70 bridge_fan_speed = 100 @@ -2543,8 +2897,8 @@ temperature = 210 [printer:Sovol SV06] autoemit_temperature_commands = 1 -bed_custom_model = /home/bassam/3dprinter/_tools/Ellis-SuperSlicer-Profiles/misc/sv06/SV06BuildPlate.stl -bed_custom_texture = /home/bassam/3dprinter/_tools/Ellis-SuperSlicer-Profiles/misc/sv06/sv06-buildplate-better.png +bed_custom_model = +bed_custom_texture = bed_shape = 0x0,223x0,223x223,0x223 before_layer_gcode = between_objects_gcode = @@ -2624,8 +2978,8 @@ z_offset = 0 [printer:Sovol SV06 Plus] autoemit_temperature_commands = 1 -bed_custom_model = /home/bassam/3dprinter/_tools/Ellis-SuperSlicer-Profiles/misc/sv06/SV06BuildPlate.stl -bed_custom_texture = /home/bassam/3dprinter/_tools/Ellis-SuperSlicer-Profiles/misc/sv06/sv06-buildplate-better.png +bed_custom_model = +bed_custom_texture = bed_shape = 0x0,300x0,300x300,0x300 before_layer_gcode = between_objects_gcode = @@ -2703,9 +3057,171 @@ variable_layer_height = 1 wipe = 0 z_offset = 0 +[printer:Sovol SV07] +autoemit_temperature_commands = 1 +bed_custom_model = +bed_custom_texture = +bed_shape = 0x0,220x0,220x220,0x220 +before_layer_gcode = +between_objects_gcode = +color_change_gcode = M600 +cooling_tube_length = 5 +cooling_tube_retraction = 91.5 +default_filament_profile = "Prusament PLA" +default_print_profile = 0.15mm QUALITY @MK3 +deretract_speed = 40 +end_gcode = PRINT_END +extra_loading_move = -2 +extruder_colour = #FFE3CA +extruder_offset = 0x0 +gcode_flavor = klipper +high_current_on_filament_swap = 0 +host_type = octoprint +inherits = +layer_gcode = +machine_limits_usage = time_estimate_only +machine_max_acceleration_e = 5000,5000 +machine_max_acceleration_extruding = 1250,1250 +machine_max_acceleration_retracting = 1250,1250 +machine_max_acceleration_travel = 1500,1250 +machine_max_acceleration_x = 1000,960 +machine_max_acceleration_y = 1000,960 +machine_max_acceleration_z = 200,200 +machine_max_feedrate_e = 120,120 +machine_max_feedrate_x = 200,100 +machine_max_feedrate_y = 200,100 +machine_max_feedrate_z = 12,12 +machine_max_jerk_e = 4.5,4.5 +machine_max_jerk_x = 8,8 +machine_max_jerk_y = 8,8 +machine_max_jerk_z = 0.4,0.4 +machine_min_extruding_rate = 0,0 +machine_min_travel_rate = 0,0 +max_layer_height = 0 +max_print_height = 250 +min_layer_height = 0.04 +nozzle_diameter = 0.4 +parking_pos_retraction = 92 +pause_print_gcode = PAUSE +print_host = +printer_model = +printer_notes = +printer_settings_id = Sovol Sv06 +printer_technology = FFF +printer_variant = 0.4 +printer_vendor = +printhost_apikey = +printhost_cafile = +remaining_times = 1 +retract_before_travel = 2 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 0.5 +retract_length_toolchange = 10 +retract_lift = 0 +retract_lift_above = 0.2 +retract_lift_below = 250 +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 40 +silent_mode = 0 +single_extruder_multi_material = 0 +start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\n; PURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code +template_custom_gcode = +thumbnails = 32x32,400x300 +thumbnails_format = PNG +toolchange_gcode = +use_firmware_retraction = 0 +use_relative_e_distances = 1 +use_volumetric_e = 0 +variable_layer_height = 1 +wipe = 0 +z_offset = 0 + +[printer:Sovol SV07 Plus] +autoemit_temperature_commands = 1 +bed_custom_model = +bed_custom_texture = +bed_shape = 0x0,300x0,300x300,0x300 +before_layer_gcode = +between_objects_gcode = +color_change_gcode = M600 +cooling_tube_length = 5 +cooling_tube_retraction = 91.5 +default_filament_profile = "Prusament PLA" +default_print_profile = 0.15mm QUALITY @MK3 +deretract_speed = 40 +end_gcode = PRINT_END +extra_loading_move = -2 +extruder_colour = #FFE3CA +extruder_offset = 0x0 +gcode_flavor = klipper +high_current_on_filament_swap = 0 +host_type = octoprint +inherits = +layer_gcode = +machine_limits_usage = time_estimate_only +machine_max_acceleration_e = 5000,5000 +machine_max_acceleration_extruding = 1250,1250 +machine_max_acceleration_retracting = 1250,1250 +machine_max_acceleration_travel = 1500,1250 +machine_max_acceleration_x = 1000,960 +machine_max_acceleration_y = 1000,960 +machine_max_acceleration_z = 200,200 +machine_max_feedrate_e = 120,120 +machine_max_feedrate_x = 200,100 +machine_max_feedrate_y = 200,100 +machine_max_feedrate_z = 12,12 +machine_max_jerk_e = 4.5,4.5 +machine_max_jerk_x = 8,8 +machine_max_jerk_y = 8,8 +machine_max_jerk_z = 0.4,0.4 +machine_min_extruding_rate = 0,0 +machine_min_travel_rate = 0,0 +max_layer_height = 0 +max_print_height = 350 +min_layer_height = 0.04 +nozzle_diameter = 0.4 +parking_pos_retraction = 92 +pause_print_gcode = PAUSE +print_host = +printer_model = +printer_notes = +printer_settings_id = Sovol Sv06 +printer_technology = FFF +printer_variant = 0.4 +printer_vendor = +printhost_apikey = +printhost_cafile = +remaining_times = 1 +retract_before_travel = 2 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 0.5 +retract_length_toolchange = 10 +retract_lift = 0 +retract_lift_above = 0.2 +retract_lift_below = 250 +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 40 +silent_mode = 0 +single_extruder_multi_material = 0 +start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND=[first_layer_temperature[initial_extruder]]\r\n; PURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code +template_custom_gcode = +thumbnails = 32x32,400x300 +thumbnails_format = PNG +toolchange_gcode = +use_firmware_retraction = 0 +use_relative_e_distances = 1 +use_volumetric_e = 0 +variable_layer_height = 1 +wipe = 0 +z_offset = 0 + [physical_printer:Local SV06] host_type = octoprint -preset_name = +preset_name = Sovol SV06 preset_names = "Sovol SV06" print_host = http://10.0.0.51 printer_technology = FFF @@ -2719,7 +3235,7 @@ printhost_user = [physical_printer:Local SV06 Plus] host_type = octoprint -preset_name = +preset_name = Sovol SV06 Plus preset_names = "Sovol SV06 Plus" print_host = http://10.0.0.51 printer_technology = FFF @@ -2731,8 +3247,36 @@ printhost_port = printhost_ssl_ignore_revoke = 0 printhost_user = +[physical_printer:Local SV07] +host_type = octoprint +preset_name = Sovol SV07 +preset_names = "Sovol SV07" +print_host = http://10.0.0.51 +printer_technology = FFF +printhost_apikey = +printhost_authorization_type = key +printhost_cafile = +printhost_password = +printhost_port = +printhost_ssl_ignore_revoke = 0 +printhost_user = + +[physical_printer:Local SV07 Plus] +host_type = octoprint +preset_name = Sovol SV07 Plus +preset_names = "Sovol SV07 Plus" +print_host = http://10.0.0.51 +printer_technology = FFF +printhost_apikey = +printhost_authorization_type = key +printhost_cafile = +printhost_password = +printhost_port = +printhost_ssl_ignore_revoke = 0 +printhost_user = + [presets] -print = Ellis_Decorative_Standard_15mm3 +print = _Ellis_PIF_Standard_15mm3_CoreXY-Speeds sla_print = sla_material = printer = Sovol SV06 diff --git a/misc/SuperSlicer_config_bundle-SV06-Both.ini b/misc/SuperSlicer_config_bundle-SV06-SV07-All.ini similarity index 90% rename from misc/SuperSlicer_config_bundle-SV06-Both.ini rename to misc/SuperSlicer_config_bundle-SV06-SV07-All.ini index c31c8a2..599d78e 100644 --- a/misc/SuperSlicer_config_bundle-SV06-Both.ini +++ b/misc/SuperSlicer_config_bundle-SV06-SV07-All.ini @@ -1,6 +1,6 @@ -# generated by SuperSlicer 2.4 on 2023-11-23 at 19:03:00 UTC +# generated by SuperSlicer 2.4 on 2023-12-01 at 18:42:11 UTC -[print:Ellis_Decorative_45_Degree_15mm3] +[print:Ellis_Decorative_45_Degree_15mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -8,17 +8,17 @@ avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonicgapfill bottom_solid_layers = 3 bottom_solid_min_thickness = 0.6 -bridge_acceleration = 3000 +bridge_acceleration = 5000 bridge_angle = 0 bridge_flow_ratio = 85% -bridge_internal_acceleration = 3000 +bridge_internal_acceleration = 5000 bridge_overlap = 50% bridge_overlap_min = 50% bridge_speed = 140 bridge_speed_internal = 100% bridge_type = nozzle bridged_infill_margin = 300% -brim_acceleration = 1000 +brim_acceleration = 5000 brim_ears = 0 brim_ears_detection_length = 1 brim_ears_max_angle = 120 @@ -39,7 +39,7 @@ curve_smoothing_angle_concave = 0 curve_smoothing_angle_convex = 0 curve_smoothing_cutoff_dist = 2 curve_smoothing_precision = 0 -default_acceleration = 3500 +default_acceleration = 4000 default_speed = 100 dont_support_bridges = 1 draft_shield = disabled @@ -49,7 +49,7 @@ enforce_retract_first_layer = 0 ensure_vertical_shell_thickness = 0 exact_last_layer_height = 0 external_infill_margin = 4 -external_perimeter_acceleration = 750 +external_perimeter_acceleration = 1000 external_perimeter_cut_corners = 0% external_perimeter_extrusion_spacing = external_perimeter_extrusion_width = 0 @@ -73,7 +73,7 @@ fill_pattern = monotonic fill_smooth_distribution = 10% fill_smooth_width = 50% fill_top_flow_ratio = 100% -first_layer_acceleration = 1000 +first_layer_acceleration = 2000 first_layer_acceleration_over_raft = 0 first_layer_extrusion_spacing = first_layer_extrusion_width = 125% @@ -88,7 +88,7 @@ first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 200% fuzzy_skin_thickness = 150% -gap_fill_acceleration = 1000 +gap_fill_acceleration = 2000 gap_fill_enabled = 1 gap_fill_flow_match_perimeter = 0% gap_fill_last = 1 @@ -104,7 +104,7 @@ hole_size_threshold = 100 hole_to_polyhole = 0 hole_to_polyhole_threshold = 0.01 hole_to_polyhole_twisted = 1 -infill_acceleration = 3500 +infill_acceleration = 7000 infill_anchor = 600% infill_anchor_max = 0 infill_connection = connected @@ -124,14 +124,14 @@ infill_speed = 300 inherits = interface_shells = 0 ironing = 0 -ironing_acceleration = 1000 +ironing_acceleration = 2000 ironing_angle = -1 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 -max_print_speed = 200 +max_print_speed = 300 max_volumetric_speed = 15 milling_after_z = 200% milling_extra_size = 150% @@ -150,13 +150,13 @@ only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode over_bridge_flow_ratio = 100% -overhangs_acceleration = 1000 +overhangs_acceleration = 2000 overhangs_reverse = 0 overhangs_reverse_threshold = 250% overhangs_speed = 100% overhangs_width = 75% overhangs_width_speed = 0 -perimeter_acceleration = 1000 +perimeter_acceleration = 2000 perimeter_bonding = 0% perimeter_extruder = 1 perimeter_extrusion_spacing = @@ -197,7 +197,7 @@ small_perimeter_max_length = 20 small_perimeter_min_length = 6 small_perimeter_speed = 30 solid_fill_pattern = monotonic -solid_infill_acceleration = 3000 +solid_infill_acceleration = 5000 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -209,7 +209,7 @@ solid_over_perimeters = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 -support_material_acceleration = 3500 +support_material_acceleration = 5000 support_material_angle = 45 support_material_auto = 1 support_material_bottom_contact_distance = 0 @@ -221,7 +221,7 @@ support_material_contact_distance_type = filament support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 -support_material_interface_acceleration = 3500 +support_material_interface_acceleration = 5000 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 @@ -239,7 +239,7 @@ support_material_xy_spacing = 75% thin_perimeters = 80% thin_perimeters_all = 20% thin_walls = 1 -thin_walls_acceleration = 750 +thin_walls_acceleration = 2000 thin_walls_merge = 1 thin_walls_min_width = 33% thin_walls_overlap = 50% @@ -248,13 +248,13 @@ threads = 16 top_fill_pattern = monotonicgapfill top_infill_extrusion_spacing = top_infill_extrusion_width = 100% -top_solid_infill_acceleration = 1000 +top_solid_infill_acceleration = 2000 top_solid_infill_speed = 60 top_solid_layers = 5 top_solid_min_thickness = 1 -travel_acceleration = 3500 +travel_acceleration = 7000 travel_deceleration_use_target = 1 -travel_speed = 200 +travel_speed = 300 travel_speed_z = 0 wipe_tower = 0 wipe_tower_bridging = 10 @@ -267,7 +267,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:Ellis_Decorative_Standard_15mm3] +[print:Ellis_Decorative_Standard_15mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -275,17 +275,17 @@ avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonicgapfill bottom_solid_layers = 3 bottom_solid_min_thickness = 0.6 -bridge_acceleration = 3000 +bridge_acceleration = 5000 bridge_angle = 0 bridge_flow_ratio = 85% -bridge_internal_acceleration = 3000 +bridge_internal_acceleration = 5000 bridge_overlap = 50% bridge_overlap_min = 50% bridge_speed = 140 bridge_speed_internal = 100% bridge_type = nozzle bridged_infill_margin = 300% -brim_acceleration = 1000 +brim_acceleration = 5000 brim_ears = 0 brim_ears_detection_length = 1 brim_ears_max_angle = 120 @@ -306,7 +306,7 @@ curve_smoothing_angle_concave = 0 curve_smoothing_angle_convex = 0 curve_smoothing_cutoff_dist = 2 curve_smoothing_precision = 0 -default_acceleration = 3500 +default_acceleration = 4000 default_speed = 100 dont_support_bridges = 1 draft_shield = disabled @@ -316,7 +316,7 @@ enforce_retract_first_layer = 0 ensure_vertical_shell_thickness = 0 exact_last_layer_height = 0 external_infill_margin = 4 -external_perimeter_acceleration = 750 +external_perimeter_acceleration = 1000 external_perimeter_cut_corners = 0% external_perimeter_extrusion_spacing = external_perimeter_extrusion_width = 0 @@ -340,7 +340,7 @@ fill_pattern = monotonic fill_smooth_distribution = 10% fill_smooth_width = 50% fill_top_flow_ratio = 100% -first_layer_acceleration = 1000 +first_layer_acceleration = 2000 first_layer_acceleration_over_raft = 0 first_layer_extrusion_spacing = first_layer_extrusion_width = 125% @@ -355,7 +355,7 @@ first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 200% fuzzy_skin_thickness = 150% -gap_fill_acceleration = 1000 +gap_fill_acceleration = 2000 gap_fill_enabled = 1 gap_fill_flow_match_perimeter = 0% gap_fill_last = 1 @@ -371,7 +371,7 @@ hole_size_threshold = 100 hole_to_polyhole = 0 hole_to_polyhole_threshold = 0.01 hole_to_polyhole_twisted = 1 -infill_acceleration = 3500 +infill_acceleration = 7000 infill_anchor = 600% infill_anchor_max = 0 infill_connection = connected @@ -391,14 +391,14 @@ infill_speed = 300 inherits = interface_shells = 0 ironing = 0 -ironing_acceleration = 1000 +ironing_acceleration = 2000 ironing_angle = -1 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 -max_print_speed = 200 +max_print_speed = 300 max_volumetric_speed = 15 milling_after_z = 200% milling_extra_size = 150% @@ -417,13 +417,13 @@ only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode over_bridge_flow_ratio = 100% -overhangs_acceleration = 1000 +overhangs_acceleration = 2000 overhangs_reverse = 0 overhangs_reverse_threshold = 250% overhangs_speed = 100% overhangs_width = 75% overhangs_width_speed = 0 -perimeter_acceleration = 1000 +perimeter_acceleration = 2000 perimeter_bonding = 0% perimeter_extruder = 1 perimeter_extrusion_spacing = @@ -464,7 +464,7 @@ small_perimeter_max_length = 20 small_perimeter_min_length = 6 small_perimeter_speed = 30 solid_fill_pattern = monotonic -solid_infill_acceleration = 3000 +solid_infill_acceleration = 5000 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -476,7 +476,7 @@ solid_over_perimeters = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 1 -support_material_acceleration = 3500 +support_material_acceleration = 5000 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0 @@ -488,7 +488,7 @@ support_material_contact_distance_type = filament support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 -support_material_interface_acceleration = 3500 +support_material_interface_acceleration = 5000 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 @@ -506,7 +506,7 @@ support_material_xy_spacing = 75% thin_perimeters = 80% thin_perimeters_all = 20% thin_walls = 1 -thin_walls_acceleration = 750 +thin_walls_acceleration = 2000 thin_walls_merge = 1 thin_walls_min_width = 33% thin_walls_overlap = 50% @@ -515,13 +515,13 @@ threads = 16 top_fill_pattern = monotonicgapfill top_infill_extrusion_spacing = top_infill_extrusion_width = 100% -top_solid_infill_acceleration = 1000 +top_solid_infill_acceleration = 2000 top_solid_infill_speed = 60 top_solid_layers = 5 top_solid_min_thickness = 1 -travel_acceleration = 3500 +travel_acceleration = 7000 travel_deceleration_use_target = 1 -travel_speed = 200 +travel_speed = 300 travel_speed_z = 0 wipe_tower = 0 wipe_tower_bridging = 10 @@ -534,7 +534,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:Ellis_PIF_45_Degree_15mm3] +[print:Ellis_PIF_45_Degree_15mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -542,17 +542,17 @@ avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonicgapfill bottom_solid_layers = 5 bottom_solid_min_thickness = 1 -bridge_acceleration = 3000 +bridge_acceleration = 5000 bridge_angle = 0 bridge_flow_ratio = 85% -bridge_internal_acceleration = 3000 +bridge_internal_acceleration = 5000 bridge_overlap = 50% bridge_overlap_min = 50% bridge_speed = 140 bridge_speed_internal = 100% bridge_type = nozzle bridged_infill_margin = 300% -brim_acceleration = 1000 +brim_acceleration = 5000 brim_ears = 0 brim_ears_detection_length = 1 brim_ears_max_angle = 120 @@ -573,7 +573,7 @@ curve_smoothing_angle_concave = 0 curve_smoothing_angle_convex = 0 curve_smoothing_cutoff_dist = 2 curve_smoothing_precision = 0 -default_acceleration = 3500 +default_acceleration = 4000 default_speed = 100 dont_support_bridges = 1 draft_shield = disabled @@ -583,7 +583,7 @@ enforce_retract_first_layer = 0 ensure_vertical_shell_thickness = 0 exact_last_layer_height = 0 external_infill_margin = 4 -external_perimeter_acceleration = 750 +external_perimeter_acceleration = 1000 external_perimeter_cut_corners = 0% external_perimeter_extrusion_spacing = external_perimeter_extrusion_width = 100% @@ -607,7 +607,7 @@ fill_pattern = grid fill_smooth_distribution = 10% fill_smooth_width = 50% fill_top_flow_ratio = 100% -first_layer_acceleration = 1000 +first_layer_acceleration = 2000 first_layer_acceleration_over_raft = 0 first_layer_extrusion_spacing = first_layer_extrusion_width = 125% @@ -622,7 +622,7 @@ first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 200% fuzzy_skin_thickness = 150% -gap_fill_acceleration = 1000 +gap_fill_acceleration = 2000 gap_fill_enabled = 1 gap_fill_flow_match_perimeter = 0% gap_fill_last = 1 @@ -638,7 +638,7 @@ hole_size_threshold = 100 hole_to_polyhole = 0 hole_to_polyhole_threshold = 0.01 hole_to_polyhole_twisted = 1 -infill_acceleration = 3500 +infill_acceleration = 7000 infill_anchor = 600% infill_anchor_max = 0 infill_connection = connected @@ -658,14 +658,14 @@ infill_speed = 300 inherits = interface_shells = 0 ironing = 0 -ironing_acceleration = 1000 +ironing_acceleration = 2000 ironing_angle = -1 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 -max_print_speed = 200 +max_print_speed = 300 max_volumetric_speed = 15 milling_after_z = 200% milling_extra_size = 150% @@ -684,13 +684,13 @@ only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode over_bridge_flow_ratio = 100% -overhangs_acceleration = 1000 +overhangs_acceleration = 2000 overhangs_reverse = 0 overhangs_reverse_threshold = 250% overhangs_speed = 100% overhangs_width = 75% overhangs_width_speed = 0 -perimeter_acceleration = 1000 +perimeter_acceleration = 2000 perimeter_bonding = 0% perimeter_extruder = 1 perimeter_extrusion_spacing = @@ -731,7 +731,7 @@ small_perimeter_max_length = 20 small_perimeter_min_length = 6 small_perimeter_speed = 30 solid_fill_pattern = monotonic -solid_infill_acceleration = 3000 +solid_infill_acceleration = 5000 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -743,7 +743,7 @@ solid_over_perimeters = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 -support_material_acceleration = 3500 +support_material_acceleration = 5000 support_material_angle = 45 support_material_auto = 1 support_material_bottom_contact_distance = 0 @@ -755,7 +755,7 @@ support_material_contact_distance_type = filament support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 -support_material_interface_acceleration = 3500 +support_material_interface_acceleration = 5000 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 @@ -773,7 +773,7 @@ support_material_xy_spacing = 75% thin_perimeters = 80% thin_perimeters_all = 20% thin_walls = 1 -thin_walls_acceleration = 750 +thin_walls_acceleration = 2000 thin_walls_merge = 1 thin_walls_min_width = 33% thin_walls_overlap = 50% @@ -782,13 +782,13 @@ threads = 16 top_fill_pattern = monotonicgapfill top_infill_extrusion_spacing = top_infill_extrusion_width = 100% -top_solid_infill_acceleration = 1000 +top_solid_infill_acceleration = 2000 top_solid_infill_speed = 60 top_solid_layers = 5 top_solid_min_thickness = 1 -travel_acceleration = 3500 +travel_acceleration = 7000 travel_deceleration_use_target = 1 -travel_speed = 200 +travel_speed = 300 travel_speed_z = 0 wipe_tower = 0 wipe_tower_bridging = 10 @@ -801,7 +801,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:Ellis_PIF_Standard_15mm3] +[print:Ellis_PIF_Standard_15mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -809,17 +809,17 @@ avoid_crossing_perimeters_max_detour = 0 bottom_fill_pattern = monotonicgapfill bottom_solid_layers = 5 bottom_solid_min_thickness = 1 -bridge_acceleration = 3000 +bridge_acceleration = 5000 bridge_angle = 0 bridge_flow_ratio = 85% -bridge_internal_acceleration = 3000 +bridge_internal_acceleration = 5000 bridge_overlap = 50% bridge_overlap_min = 50% bridge_speed = 140 bridge_speed_internal = 100% bridge_type = nozzle bridged_infill_margin = 300% -brim_acceleration = 1000 +brim_acceleration = 5000 brim_ears = 0 brim_ears_detection_length = 1 brim_ears_max_angle = 120 @@ -840,7 +840,7 @@ curve_smoothing_angle_concave = 0 curve_smoothing_angle_convex = 0 curve_smoothing_cutoff_dist = 2 curve_smoothing_precision = 0 -default_acceleration = 3500 +default_acceleration = 4000 default_speed = 100 dont_support_bridges = 1 draft_shield = disabled @@ -850,7 +850,7 @@ enforce_retract_first_layer = 0 ensure_vertical_shell_thickness = 0 exact_last_layer_height = 0 external_infill_margin = 4 -external_perimeter_acceleration = 750 +external_perimeter_acceleration = 1000 external_perimeter_cut_corners = 0% external_perimeter_extrusion_spacing = external_perimeter_extrusion_width = 100% @@ -874,7 +874,7 @@ fill_pattern = grid fill_smooth_distribution = 10% fill_smooth_width = 50% fill_top_flow_ratio = 100% -first_layer_acceleration = 1000 +first_layer_acceleration = 2000 first_layer_acceleration_over_raft = 0 first_layer_extrusion_spacing = first_layer_extrusion_width = 125% @@ -889,7 +889,7 @@ first_layer_speed_over_raft = 30 fuzzy_skin = none fuzzy_skin_point_dist = 200% fuzzy_skin_thickness = 150% -gap_fill_acceleration = 1000 +gap_fill_acceleration = 2000 gap_fill_enabled = 1 gap_fill_flow_match_perimeter = 0% gap_fill_last = 1 @@ -905,7 +905,7 @@ hole_size_threshold = 100 hole_to_polyhole = 0 hole_to_polyhole_threshold = 0.01 hole_to_polyhole_twisted = 1 -infill_acceleration = 3500 +infill_acceleration = 7000 infill_anchor = 600% infill_anchor_max = 0 infill_connection = connected @@ -925,14 +925,14 @@ infill_speed = 300 inherits = interface_shells = 0 ironing = 0 -ironing_acceleration = 1000 +ironing_acceleration = 2000 ironing_angle = -1 ironing_flowrate = 15% ironing_spacing = 0.1 ironing_speed = 15 ironing_type = top layer_height = 0.2 -max_print_speed = 200 +max_print_speed = 300 max_volumetric_speed = 15 milling_after_z = 200% milling_extra_size = 150% @@ -951,13 +951,13 @@ only_retract_when_crossing_perimeters = 1 ooze_prevention = 0 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode over_bridge_flow_ratio = 100% -overhangs_acceleration = 1000 +overhangs_acceleration = 2000 overhangs_reverse = 0 overhangs_reverse_threshold = 250% overhangs_speed = 100% overhangs_width = 75% overhangs_width_speed = 0 -perimeter_acceleration = 1000 +perimeter_acceleration = 2000 perimeter_bonding = 0% perimeter_extruder = 1 perimeter_extrusion_spacing = @@ -998,7 +998,7 @@ small_perimeter_max_length = 20 small_perimeter_min_length = 6 small_perimeter_speed = 30 solid_fill_pattern = monotonic -solid_infill_acceleration = 3000 +solid_infill_acceleration = 5000 solid_infill_below_area = 0 solid_infill_every_layers = 0 solid_infill_extruder = 1 @@ -1010,7 +1010,7 @@ solid_over_perimeters = 0 spiral_vase = 0 standby_temperature_delta = -5 support_material = 0 -support_material_acceleration = 3500 +support_material_acceleration = 5000 support_material_angle = 0 support_material_auto = 1 support_material_bottom_contact_distance = 0 @@ -1022,7 +1022,7 @@ support_material_contact_distance_type = filament support_material_enforce_layers = 0 support_material_extruder = 1 support_material_extrusion_width = 0 -support_material_interface_acceleration = 3500 +support_material_interface_acceleration = 5000 support_material_interface_contact_loops = 0 support_material_interface_extruder = 1 support_material_interface_layers = 2 @@ -1040,7 +1040,7 @@ support_material_xy_spacing = 75% thin_perimeters = 80% thin_perimeters_all = 20% thin_walls = 1 -thin_walls_acceleration = 750 +thin_walls_acceleration = 2000 thin_walls_merge = 1 thin_walls_min_width = 33% thin_walls_overlap = 50% @@ -1049,13 +1049,13 @@ threads = 16 top_fill_pattern = monotonicgapfill top_infill_extrusion_spacing = top_infill_extrusion_width = 100% -top_solid_infill_acceleration = 1000 +top_solid_infill_acceleration = 2000 top_solid_infill_speed = 60 top_solid_layers = 5 top_solid_min_thickness = 1 -travel_acceleration = 3500 +travel_acceleration = 7000 travel_deceleration_use_target = 1 -travel_speed = 200 +travel_speed = 300 travel_speed_z = 0 wipe_tower = 0 wipe_tower_bridging = 10 @@ -1068,7 +1068,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:_Ellis_Decorative_45_Degree_15mm3-CoreXY-Speeds] +[print:_Ellis_Decorative_45_Degree_24mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -1200,7 +1200,7 @@ ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 300 -max_volumetric_speed = 15 +max_volumetric_speed = 24 milling_after_z = 200% milling_extra_size = 150% milling_post_process = 0 @@ -1335,7 +1335,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:_Ellis_Decorative_Standard_15mm3-CoreXY-Speeds] +[print:_Ellis_Decorative_Standard_24mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -1467,7 +1467,7 @@ ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 300 -max_volumetric_speed = 15 +max_volumetric_speed = 24 milling_after_z = 200% milling_extra_size = 150% milling_post_process = 0 @@ -1602,7 +1602,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:_Ellis_PIF_45_Degree_15mm3-CoreXY-Speeds] +[print:_Ellis_PIF_45_Degree_24mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -1734,7 +1734,7 @@ ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 300 -max_volumetric_speed = 15 +max_volumetric_speed = 24 milling_after_z = 200% milling_extra_size = 150% milling_post_process = 0 @@ -1869,7 +1869,7 @@ wipe_tower_y = 140 xy_inner_size_compensation = 0 xy_size_compensation = 0 -[print:_Ellis_PIF_Standard_15mm3-CoreXY-Speeds] +[print:_Ellis_PIF_Standard_24mm3-CoreXY-Speeds] allow_empty_layers = 0 avoid_crossing_not_first_layer = 1 avoid_crossing_perimeters = 0 @@ -2001,7 +2001,7 @@ ironing_speed = 15 ironing_type = top layer_height = 0.2 max_print_speed = 300 -max_volumetric_speed = 15 +max_volumetric_speed = 24 milling_after_z = 200% milling_extra_size = 150% milling_post_process = 0 @@ -3615,9 +3615,9 @@ support_material_interface_fan_speed = -1 temperature = 210 top_fan_speed = -1 -[printer:Sovol Sv06] -bed_custom_model = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/SV06BuildPlate.stl -bed_custom_texture = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/sv06-buildplate-better.png +[printer:Sovol SV06] +bed_custom_model = +bed_custom_texture = bed_shape = 0x0,223x0,223x223,0x223 before_layer_gcode = between_objects_gcode = @@ -3682,7 +3682,7 @@ print_host = printer_custom_variables = printer_model = printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n -printer_settings_id = Sovol Sv06 +printer_settings_id = Sovol SV06 printer_technology = FFF printer_variant = 0.4 printer_vendor = @@ -3740,9 +3740,9 @@ wipe_speed = 0 z_offset = 0 z_step = 0.005 -[printer:Sovol Sv06 Plus] -bed_custom_model = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/SV06BuildPlate.stl -bed_custom_texture = /home/bassam/3dprinter/voron/voron-0-parts/Ellis-SuperSlicer-Profiles/misc/sv06/sv06-buildplate-better.png +[printer:Sovol SV06 Plus] +bed_custom_model = +bed_custom_texture = bed_shape = 0x0,300x0,300x300,0x300 before_layer_gcode = between_objects_gcode = @@ -3807,7 +3807,7 @@ print_host = printer_custom_variables = printer_model = printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n -printer_settings_id = Sovol Sv06 +printer_settings_id = Sovol SV06 printer_technology = FFF printer_variant = 0.4 printer_vendor = @@ -3865,10 +3865,260 @@ wipe_speed = 0 z_offset = 0 z_step = 0.005 -[physical_printer:Local] +[printer:Sovol SV07] +bed_custom_model = +bed_custom_texture = +bed_shape = 0x0,220x0,220x220,0x220 +before_layer_gcode = +between_objects_gcode = +color_change_gcode = M600 +cooling_tube_length = 5 +cooling_tube_retraction = 91.5 +default_filament_profile = "Prusament PLA" +default_print_profile = 0.15mm QUALITY @MK3 +deretract_speed = 40 +end_gcode = PRINT_END +extra_loading_move = -2 +extruder_colour = #FFE3CA +extruder_fan_offset = 0% +extruder_offset = 0x0 +extruder_temperature_offset = 0 +fan_kickstart = 0 +fan_percentage = 0 +fan_speedup_overhangs = 1 +fan_speedup_time = 0 +feature_gcode = +gcode_filename_illegal_char = [<>:"/\\\\|?*] +gcode_flavor = klipper +gcode_precision_e = 5 +gcode_precision_xyz = 3 +high_current_on_filament_swap = 0 host_type = octoprint -preset_name = Sovol Sv06 -preset_names = "Sovol Sv06" +inherits = +init_z_rotate = 0 +layer_gcode = +lift_min = 0 +machine_limits_usage = time_estimate_only +machine_max_acceleration_e = 5000,5000 +machine_max_acceleration_extruding = 1250,1250 +machine_max_acceleration_retracting = 1250,1250 +machine_max_acceleration_travel = 1500,1250 +machine_max_acceleration_x = 1000,960 +machine_max_acceleration_y = 1000,960 +machine_max_acceleration_z = 200,200 +machine_max_feedrate_e = 120,120 +machine_max_feedrate_x = 200,100 +machine_max_feedrate_y = 200,100 +machine_max_feedrate_z = 12,12 +machine_max_jerk_e = 4.5,4.5 +machine_max_jerk_x = 8,8 +machine_max_jerk_y = 8,8 +machine_max_jerk_z = 0.4,0.4 +machine_min_extruding_rate = 0,0 +machine_min_travel_rate = 0,0 +max_gcode_per_second = 1500 +max_layer_height = 75% +max_print_height = 250 +milling_diameter = +milling_toolchange_end_gcode = +milling_toolchange_start_gcode = +milling_z_lift = +min_layer_height = 0.04 +min_length = 0.035 +nozzle_diameter = 0.4 +parking_pos_retraction = 92 +pause_print_gcode = PAUSE +print_host = +printer_custom_variables = +printer_model = +printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n +printer_settings_id = Sovol SV06 +printer_technology = FFF +printer_variant = 0.4 +printer_vendor = +printhost_apikey = +printhost_cafile = +printhost_port = +remaining_times = 1 +remaining_times_type = m73 +retract_before_travel = 2 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 0.5 +retract_length_toolchange = 10 +retract_lift = 0 +retract_lift_above = 0.2 +retract_lift_below = 250 +retract_lift_first_layer = 0 +retract_lift_top = "All surfaces" +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 40 +seam_gap = 15% +silent_mode = 0 +single_extruder_multi_material = 0 +start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} CHAMBER=[chamber_temperature]\r\nPURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code +start_gcode_manual = 0 +template_custom_gcode = +thumbnails = 32x32,400x300 +thumbnails_color = #00FF00 +thumbnails_custom_color = 1 +thumbnails_end_file = 0 +thumbnails_format = PNG +thumbnails_with_bed = 1 +time_cost = 0 +time_estimation_compensation = 100% +time_start_gcode = 20 +time_toolchange = 30 +tool_name = "" +toolchange_gcode = +use_firmware_retraction = 0 +use_relative_e_distances = 1 +use_volumetric_e = 0 +variable_layer_height = 1 +wipe = 0 +wipe_advanced = 0 +wipe_advanced_algo = linear +wipe_advanced_multiplier = 60 +wipe_advanced_nozzle_melted_volume = 120 +wipe_extra_perimeter = 0 +wipe_inside_depth = 50% +wipe_inside_end = 1 +wipe_inside_start = 0 +wipe_only_crossing = 1 +wipe_speed = 0 +z_offset = 0 +z_step = 0.005 + +[printer:Sovol SV07 Plus] +bed_custom_model = +bed_custom_texture = +bed_shape = 0x0,300x0,300x300,0x300 +before_layer_gcode = +between_objects_gcode = +color_change_gcode = M600 +cooling_tube_length = 5 +cooling_tube_retraction = 91.5 +default_filament_profile = "Prusament PLA" +default_print_profile = 0.15mm QUALITY @MK3 +deretract_speed = 40 +end_gcode = PRINT_END +extra_loading_move = -2 +extruder_colour = #FFE3CA +extruder_fan_offset = 0% +extruder_offset = 0x0 +extruder_temperature_offset = 0 +fan_kickstart = 0 +fan_percentage = 0 +fan_speedup_overhangs = 1 +fan_speedup_time = 0 +feature_gcode = +gcode_filename_illegal_char = [<>:"/\\\\|?*] +gcode_flavor = klipper +gcode_precision_e = 5 +gcode_precision_xyz = 3 +high_current_on_filament_swap = 0 +host_type = octoprint +inherits = +init_z_rotate = 0 +layer_gcode = +lift_min = 0 +machine_limits_usage = time_estimate_only +machine_max_acceleration_e = 5000,5000 +machine_max_acceleration_extruding = 1250,1250 +machine_max_acceleration_retracting = 1250,1250 +machine_max_acceleration_travel = 1500,1250 +machine_max_acceleration_x = 1000,960 +machine_max_acceleration_y = 1000,960 +machine_max_acceleration_z = 200,200 +machine_max_feedrate_e = 120,120 +machine_max_feedrate_x = 200,100 +machine_max_feedrate_y = 200,100 +machine_max_feedrate_z = 12,12 +machine_max_jerk_e = 4.5,4.5 +machine_max_jerk_x = 8,8 +machine_max_jerk_y = 8,8 +machine_max_jerk_z = 0.4,0.4 +machine_min_extruding_rate = 0,0 +machine_min_travel_rate = 0,0 +max_gcode_per_second = 1500 +max_layer_height = 75% +max_print_height = 350 +milling_diameter = +milling_toolchange_end_gcode = +milling_toolchange_start_gcode = +milling_z_lift = +min_layer_height = 0.04 +min_length = 0.035 +nozzle_diameter = 0.4 +parking_pos_retraction = 92 +pause_print_gcode = PAUSE +print_host = +printer_custom_variables = +printer_model = +printer_notes = Don't remove the following keywords! These keywords are used in the "compatible printer" condition of the print and filament profiles to link the particular print and filament profiles to this printer profile.\nPRINTER_VENDOR_PRUSA3D\nPRINTER_MODEL_MK3\n +printer_settings_id = Sovol SV06 +printer_technology = FFF +printer_variant = 0.4 +printer_vendor = +printhost_apikey = +printhost_cafile = +printhost_port = +remaining_times = 1 +remaining_times_type = m73 +retract_before_travel = 2 +retract_before_wipe = 0% +retract_layer_change = 1 +retract_length = 0.5 +retract_length_toolchange = 10 +retract_lift = 0 +retract_lift_above = 0.2 +retract_lift_below = 250 +retract_lift_first_layer = 0 +retract_lift_top = "All surfaces" +retract_restart_extra = 0 +retract_restart_extra_toolchange = 0 +retract_speed = 40 +seam_gap = 15% +silent_mode = 0 +single_extruder_multi_material = 0 +start_gcode = M104 S0 ; Stops PS/SS from sending temp waits separately\r\nM140 S0\nM117\r\nPRINT_START BED=[first_layer_bed_temperature] HOTEND={first_layer_temperature[initial_extruder]+extruder_temperature_offset[initial_extruder]} CHAMBER=[chamber_temperature]\r\nPURGE_LINE\n\n;; Guide: https://ellis3dp.com/Print-Tuning-Guide/articles/passing_slicer_variables.html#slicer-start-g-code +start_gcode_manual = 0 +template_custom_gcode = +thumbnails = 32x32,400x300 +thumbnails_color = #00FF00 +thumbnails_custom_color = 1 +thumbnails_end_file = 0 +thumbnails_format = PNG +thumbnails_with_bed = 1 +time_cost = 0 +time_estimation_compensation = 100% +time_start_gcode = 20 +time_toolchange = 30 +tool_name = "" +toolchange_gcode = +use_firmware_retraction = 0 +use_relative_e_distances = 1 +use_volumetric_e = 0 +variable_layer_height = 1 +wipe = 0 +wipe_advanced = 0 +wipe_advanced_algo = linear +wipe_advanced_multiplier = 60 +wipe_advanced_nozzle_melted_volume = 120 +wipe_extra_perimeter = 0 +wipe_inside_depth = 50% +wipe_inside_end = 1 +wipe_inside_start = 0 +wipe_only_crossing = 1 +wipe_speed = 0 +z_offset = 0 +z_step = 0.005 + +[physical_printer:Local SV06] +host_type = octoprint +preset_name = Sovol SV06 +preset_names = "Sovol SV06" print_host = http://10.0.0.51 printer_technology = FFF printhost_apikey = @@ -3880,10 +4130,40 @@ printhost_port = printhost_ssl_ignore_revoke = 0 printhost_user = -[physical_printer:Local Plus] +[physical_printer:Local SV06 Plus] host_type = octoprint -preset_name = Sovol Sv06 Plus -preset_names = "Sovol Sv06 Plus" +preset_name = Sovol SV06 Plus +preset_names = "Sovol SV06 Plus" +print_host = http://10.0.0.51 +printer_technology = FFF +printhost_apikey = +printhost_authorization_type = key +printhost_cafile = +printhost_client_cert = +printhost_password = +printhost_port = +printhost_ssl_ignore_revoke = 0 +printhost_user = + +[physical_printer:Local SV07] +host_type = octoprint +preset_name = Sovol SV07 +preset_names = "Sovol SV07" +print_host = http://10.0.0.51 +printer_technology = FFF +printhost_apikey = +printhost_authorization_type = key +printhost_cafile = +printhost_client_cert = +printhost_password = +printhost_port = +printhost_ssl_ignore_revoke = 0 +printhost_user = + +[physical_printer:Local SV07 Plus] +host_type = octoprint +preset_name = Sovol SV07 Plus +preset_names = "Sovol SV07 Plus" print_host = http://10.0.0.51 printer_technology = FFF printhost_apikey = @@ -3896,9 +4176,9 @@ printhost_ssl_ignore_revoke = 0 printhost_user = [presets] -print = Ellis_Decorative_Standard_15mm3 +print = Ellis_Decorative_45_Degree_15mm3-CoreXY-Speeds sla_print = sla_material = -printer = Sovol Sv06 +printer = Sovol SV06 filament = eSun PLA+ Blue physical_printer =