mirror of
https://github.com/bassamanator/Sovol-SV06-firmware.git
synced 2025-11-08 13:31:16 +00:00
Pulling in structure from personal branch.
This commit is contained in:
Bassam Husain
@@ -1,54 +0,0 @@
|
||||
[output_pin beeper]
|
||||
pin: PC6
|
||||
value: 0
|
||||
shutdown_value: 0
|
||||
pwm: True
|
||||
cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
|
||||
|
||||
[gcode_macro BEEP]
|
||||
description: BEEP I=3 DUR=200 FREQ=2000: Beep 3 times, for 200ms each, at 2kHz frequency.
|
||||
gcode:
|
||||
# Parameters
|
||||
{% set i = params.I|default(1)|int %} ; Iterations (number of times to beep).
|
||||
{% set dur = params.DUR|default(100)|int %} ; Duration/wait of each beep in ms. Default 100ms.
|
||||
{% set freq = params.FREQ|default(2000)|int %} ; Frequency in Hz. Default 2kHz.
|
||||
|
||||
{% for iteration in range(i|int) %}
|
||||
SET_PIN PIN=beeper VALUE=0.8 CYCLE_TIME={ 1.0/freq if freq > 0 else 1 }
|
||||
G4 P{dur}
|
||||
SET_PIN PIN=beeper VALUE=0
|
||||
G4 P{dur}
|
||||
{% endfor %}
|
||||
|
||||
# [gcode_macro M300]
|
||||
# gcode:
|
||||
# {% set S = params.S|default(1000)|int %}
|
||||
# {% set P = params.P|default(100)|int %}
|
||||
|
||||
# SET_PIN PIN=beeper VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
|
||||
# G4 P{P}
|
||||
# SET_PIN PIN=beeper VALUE=0
|
||||
|
||||
# [gcode_macro SONG_SINGLE_BEEP]
|
||||
# gcode:
|
||||
# M300 S830.61 P137
|
||||
|
||||
# [gcode_macro TOGGLE_BEEPER]
|
||||
# description: Toggle the printer beeper on and off.
|
||||
# gcode:
|
||||
# {% set beeper_state = printer.save_variables.variables.beeper_state|lower %}
|
||||
|
||||
# {% if printer['gcode_macro _USER_VARIABLE'].debug == 1 %}
|
||||
# {action_respond_info('==== TOGGLE_BEEPER ====')}
|
||||
# {action_respond_info("beeper_state: %s" % (beeper_state))}
|
||||
# {action_respond_info('===============')}
|
||||
# {% endif %}
|
||||
|
||||
# {% if beeper_state == "off" %}
|
||||
# {action_respond_info('beeper is off, turning it on')}
|
||||
# SAVE_VARIABLE VARIABLE=beeper_state VALUE='"on"'
|
||||
# {% else %}
|
||||
# {action_respond_info('beeper is on= turning it off')}
|
||||
# SAVE_VARIABLE VARIABLE=beeper_state VALUE='"off"'
|
||||
# {% endif %}
|
||||
# SONG_SINGLE_BEEP
|
||||
@@ -210,4 +210,19 @@ gcode:
|
||||
gcode:
|
||||
{% if "xyz" not in printer.toolhead.homed_axes %}
|
||||
G28
|
||||
{% endif %}
|
||||
{% endif %}
|
||||
|
||||
[gcode_macro BEEP]
|
||||
description: BEEP I=3 DUR=200 FREQ=2000: Beep 3 times, for 200ms each, at 2kHz frequency.
|
||||
gcode:
|
||||
# Parameters
|
||||
{% set i = params.I|default(1)|int %} ; Iterations (number of times to beep).
|
||||
{% set dur = params.DUR|default(100)|int %} ; Duration/wait of each beep in ms. Default 100ms.
|
||||
{% set freq = params.FREQ|default(2000)|int %} ; Frequency in Hz. Default 2kHz.
|
||||
|
||||
{% for iteration in range(i|int) %}
|
||||
SET_PIN PIN=beeper VALUE=0.8 CYCLE_TIME={ 1.0/freq if freq > 0 else 1 }
|
||||
G4 P{dur}
|
||||
SET_PIN PIN=beeper VALUE=0
|
||||
G4 P{dur}
|
||||
{% endfor %}
|
||||
34
printer.cfg
34
printer.cfg
@@ -7,7 +7,6 @@
|
||||
[include ./cfgs/misc-macros.cfg]
|
||||
[include ./cfgs/PARKING.cfg]
|
||||
[include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
|
||||
[include ./cfgs/beeper.cfg]
|
||||
|
||||
# NOTE Uncomment the ONE of the following lines if you're using an adxl345
|
||||
# [include ./cfgs/adxl-rp2040.cfg]
|
||||
@@ -25,6 +24,10 @@ max_accel: 3000
|
||||
max_z_velocity: 15
|
||||
max_z_accel: 45
|
||||
|
||||
#####################################################################
|
||||
# X/Y/Z Stepper Settings
|
||||
#####################################################################
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: !PB9
|
||||
@@ -89,11 +92,15 @@ sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
diag_pin: PA7
|
||||
|
||||
#####################################################################
|
||||
# Extruder
|
||||
#####################################################################
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: !PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 32
|
||||
microsteps: 64
|
||||
rotation_distance: 4.65 # NOTE Calibrate e-steps and adjust https://www.klipper3d.org/Rotation_Distance.html
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
@@ -116,6 +123,10 @@ interpolate: False
|
||||
sense_resistor: 0.150
|
||||
uart_address: 3
|
||||
|
||||
#####################################################################
|
||||
# Bed Heater
|
||||
#####################################################################
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
@@ -127,6 +138,10 @@ pid_kd: 1343.571
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
|
||||
#####################################################################
|
||||
# Probe Related
|
||||
#####################################################################
|
||||
|
||||
[probe]
|
||||
pin: PB1
|
||||
x_offset: 27
|
||||
@@ -153,9 +168,17 @@ fade_start: 1
|
||||
fade_end: 10
|
||||
fade_target: 0
|
||||
|
||||
#####################################################################
|
||||
# Fans
|
||||
#####################################################################
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
#####################################################################
|
||||
# Misc
|
||||
#####################################################################
|
||||
|
||||
[display]
|
||||
lcd_type: st7920
|
||||
cs_pin: PB12
|
||||
@@ -188,3 +211,10 @@ screw5_name: back left
|
||||
speed: 50
|
||||
horizontal_move_z: 10
|
||||
screw_thread: CCW-M4
|
||||
|
||||
[output_pin beeper]
|
||||
pin: PC6
|
||||
value: 0
|
||||
shutdown_value: 0
|
||||
pwm: True
|
||||
cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
|
||||
|
||||
Reference in New Issue
Block a user