Pulling in structure from personal branch.

cfgs/beeper.cfg

@@ -1,54 +0,0 @@
-[output_pin beeper]
-pin: PC6
-value: 0
-shutdown_value: 0
-pwm: True
-cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
-
-[gcode_macro BEEP]
-description: BEEP I=3 DUR=200 FREQ=2000: Beep 3 times, for 200ms each, at 2kHz frequency.
-gcode:
-    # Parameters
-    {% set i = params.I|default(1)|int %}           ; Iterations (number of times to beep).
-    {% set dur = params.DUR|default(100)|int %}     ; Duration/wait of each beep in ms. Default 100ms.
-    {% set freq = params.FREQ|default(2000)|int %}  ; Frequency in Hz. Default 2kHz.
-
-    {% for iteration in range(i|int) %}
-        SET_PIN PIN=beeper VALUE=0.8 CYCLE_TIME={ 1.0/freq if freq > 0 else 1 }
-        G4 P{dur}
-        SET_PIN PIN=beeper VALUE=0
-        G4 P{dur}
-    {% endfor %}
-
-# [gcode_macro M300]
-# gcode:
-# 	{% set S = params.S|default(1000)|int %}
-# 	{% set P = params.P|default(100)|int %}
-
-# 		SET_PIN PIN=beeper VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
-# 		G4 P{P}
-# 		SET_PIN PIN=beeper VALUE=0
-
-# [gcode_macro SONG_SINGLE_BEEP]
-# gcode:
-# 	M300 S830.61 P137
-
-# [gcode_macro TOGGLE_BEEPER]
-# description: Toggle the printer beeper on and off.
-# gcode:
-# 	{% set beeper_state = printer.save_variables.variables.beeper_state|lower %}
-
-# 	{% if printer['gcode_macro _USER_VARIABLE'].debug == 1 %}
-# 		{action_respond_info('==== TOGGLE_BEEPER ====')}
-# 		{action_respond_info("beeper_state: %s" % (beeper_state))}
-# 		{action_respond_info('===============')}
-# 	{% endif %}
-
-# 	{% if beeper_state == "off" %}
-# 		{action_respond_info('beeper is off, turning it on')}
-# 		SAVE_VARIABLE VARIABLE=beeper_state VALUE='"on"'
-# 	{% else %}
-# 		{action_respond_info('beeper is on= turning it off')}
-# 		SAVE_VARIABLE VARIABLE=beeper_state VALUE='"off"'
-# 	{% endif %}
-# 	SONG_SINGLE_BEEP

cfgs/misc-macros.cfg

@@ -211,3 +211,18 @@ gcode:
     {% if "xyz" not in printer.toolhead.homed_axes %}
         G28
     {% endif %}
+
+[gcode_macro BEEP]
+description: BEEP I=3 DUR=200 FREQ=2000: Beep 3 times, for 200ms each, at 2kHz frequency.
+gcode:
+    # Parameters
+    {% set i = params.I|default(1)|int %}           ; Iterations (number of times to beep).
+    {% set dur = params.DUR|default(100)|int %}     ; Duration/wait of each beep in ms. Default 100ms.
+    {% set freq = params.FREQ|default(2000)|int %}  ; Frequency in Hz. Default 2kHz.
+
+    {% for iteration in range(i|int) %}
+        SET_PIN PIN=beeper VALUE=0.8 CYCLE_TIME={ 1.0/freq if freq > 0 else 1 }
+        G4 P{dur}
+        SET_PIN PIN=beeper VALUE=0
+        G4 P{dur}
+    {% endfor %}

printer.cfg

@@ -7,7 +7,6 @@
 [include ./cfgs/misc-macros.cfg]
 [include ./cfgs/PARKING.cfg]
 [include ./cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg]
-[include ./cfgs/beeper.cfg]
 
 # NOTE Uncomment the ONE of the following lines if you're using an adxl345
 # [include ./cfgs/adxl-rp2040.cfg]
@@ -25,6 +24,10 @@ max_accel: 3000
 max_z_velocity: 15
 max_z_accel: 45
 
+#####################################################################
+#      X/Y/Z Stepper Settings
+#####################################################################
+
 [stepper_x]
 step_pin: PC2
 dir_pin: !PB9
@@ -89,11 +92,15 @@ sense_resistor: 0.150
 uart_address: 3
 diag_pin: PA7
 
+#####################################################################
+#   Extruder
+#####################################################################
+
 [extruder]
 step_pin: PB4
 dir_pin: !PB3
 enable_pin: !PC3
-microsteps: 32
+microsteps: 64
 rotation_distance: 4.65 # NOTE Calibrate e-steps and adjust https://www.klipper3d.org/Rotation_Distance.html
 nozzle_diameter: 0.400
 filament_diameter: 1.750
@@ -116,6 +123,10 @@ interpolate: False
 sense_resistor: 0.150
 uart_address: 3
 
+#####################################################################
+#   Bed Heater
+#####################################################################
+
 [heater_bed]
 heater_pin: PA2
 sensor_type: EPCOS 100K B57560G104F
@@ -127,6 +138,10 @@ pid_kd: 1343.571
 min_temp: 0
 max_temp: 110
 
+#####################################################################
+#   Probe Related
+#####################################################################
+
 [probe]
 pin: PB1
 x_offset: 27
@@ -153,9 +168,17 @@ fade_start: 1
 fade_end: 10
 fade_target: 0
 
+#####################################################################
+#   Fans
+#####################################################################
+
 [fan]
 pin: PA0
 
+#####################################################################
+#   Misc
+#####################################################################
+
 [display]
 lcd_type: st7920
 cs_pin: PB12
@@ -188,3 +211,10 @@ screw5_name: back left
 speed: 50
 horizontal_move_z: 10
 screw_thread: CCW-M4
+
+[output_pin beeper]
+pin: PC6
+value: 0
+shutdown_value: 0
+pwm: True
+cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)