PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-09 05:51:15 +00:00
Code Issues Packages Projects Releases Wiki Activity

Merge branch 'master' into sv06-plus

Browse Source
This commit is contained in:
Bassam Husain
2023-07-01 01:28:54 -04:00
parent 4cfbe14e59 d6f03f7a2c
commit 5f59d5bacb
5 changed files with 95 additions and 63 deletions
Download Patch File Download Diff File Expand all files Collapse all files

55
README.md
View File

@@ -18,10 +18,10 @@ I am creating these files for my personal use and cannot be held responsible for
- [Features](#features)
- [Stay Up-to-Date](#stay-up-to-date)
- [Preface](#preface)
- [Installation Steps](#installation-steps)
- [Before You Begin](#before-you-begin)
- [Before You Begin](#before-you-begin)
- [Klipper Installation](#klipper-installation)
- [Flash Firmware](#flash-firmware)
- [Download Klipper Configuration](#download-klipper-configuration)
- [Download OSS Klipper Configuration](#download-oss-klipper-configuration)
- [Initial Steps](#initial-steps)
1. [Adjust Configuration with MCU Path](#adjust-configuration-with-mcu-path)
2. [Configure Your Printer](#configure-your-printer)
@@ -57,9 +57,7 @@ Watch for releases and updates.
Although I've made switching over to Klipper as easy as is possible, it can still be a challenge for some, especially considering that most of you have likely never used GNU+Linux. Save yourself the frustration, and fully read all documentation found on this page. Also note that Klipper is not a _must_, and is not for everyone. You can stick with Marlin, and have a fine 3D printing experience.
## Installation Steps
### Before You Begin
## Before You Begin
- On the SV06 Plus, your screen will not work if you install Klipper. You can get it working again via the instructions found [here](https://github.com/fryc88/klipper-sv06plus-screen).
- Read this documentation _fully!_
@@ -74,6 +72,8 @@ Although I've made switching over to Klipper as easy as is possible, it can stil
- Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section.
- I would recommend searching for the word `NOTE` in this repository. There are roughly half a dozen short points amongst the various files that you should be aware of if you're using this configuration.
## Klipper Installation
### Flash Firmware
💡 _If you have already flashed klipper onto your motherboard in the past, you can skip this step._
@@ -103,7 +103,7 @@ Please note:
You may find this [video](https://youtu.be/p6l253OJa34) useful.
### Download Klipper Configuration
### Download OSS Klipper Configuration
You can choose _either_ of the 2 following methods.
@@ -155,37 +155,26 @@ If you've done everything correctly, you should see no errors or warnings in you
You will be pasting/typing these commands into the Mainsail/Fluidd console.
1. `G28`
1. Check to see if `X` and `Y` max positions (`G90`, `G1 X300 F3000`, `G1 Y300 F3000`) can be reached, and adjust `position_max`, if necessary. Note, you might be able to go even further.
2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. ~~You will hear a succession of beeps.~~
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam (`G90`, `G1 Z330 F900`, then move up mm by mm). Adjust `position_max`, if necessary.
3. Pid tune the bed, but first move the printhead to the center. Ideally, all Pid tuning should occur at the temperatures that you print most at.
1. Check to see if `X` and `Y` max positions can be reached, and adjust `position_max`, if necessary. You might be able to go further, which is great, but I recommend leaving a 2mm gap for safety.
1. `G28`
2. `G90`
3. `G1 X150 Y150 Z40 F6000`
4. `PID_CALIBRATE HEATER=heater_bed TARGET=70`
5. `SAVE_CONFIG` (once completed)
3. `G1 X300 F3000`
4. `G1 Y300 F3000`
2. Do a mechanical gantry calibration; `G34`. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up against the `stoppers` at the top. ~~You will hear a succession of beeps.~~
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam, and adjust `position_max`, if necessary.
3. PID tune the bed. Ideally, all PID tuning should occur at the temperatures that you print most at.
1. `PID_TEST_BED`
2. `SAVE_CONFIG` (once completed)
4. PID tune the extruder while part cooling fan runs at 25%.
1. `G28`
2. `G90`
3. `G1 X150 Y150 Z10 F6000`
4. `M106 S64`
5. `PID_CALIBRATE HEATER=extruder TARGET=245`
6. `SAVE_CONFIG` (once completed)
1. `PID_TEST_HOTEND`
2. `SAVE_CONFIG` (once completed)
5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test).
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`
3. Proceed to next steps after both temperatures have been reached.
4. `G28`
5. `PROBE_CALIBRATE`
6. `SAVE_CONFIG` (once completed)
1. `DO_PROBE_CALIBRATE`
2. Follow `z_offset` setup in Mainsail/Fluidd.
3. `SAVE_CONFIG` (once completed)
6. Create a bed mesh.
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`
3. Proceed to next steps after both temperatures have been reached.
4. `G28`
5. `BED_MESH_CALIBRATE`
6. `SAVE_CONFIG` (once completed)
1. `DO_CREATE_MESH`
2. `SAVE_CONFIG` (once completed)
If you've made it here, then your printer has been Klipperized, and is ready to print!