diff --git a/.eslintignore b/.eslintignore
deleted file mode 100644
index 8f21e45..0000000
--- a/.eslintignore
+++ /dev/null
@@ -1 +0,0 @@
-# *.md
\ No newline at end of file
diff --git a/.gitignore b/.gitignore
index dc8d21e..a46f989 100644
--- a/.gitignore
+++ b/.gitignore
@@ -1,3 +1,2 @@
-macros/mainsail.cfg
 printer-*_*.cfg
 .moonraker.conf.bkp
diff --git a/.prettierignore b/.prettierignore
deleted file mode 100644
index 0c06336..0000000
--- a/.prettierignore
+++ /dev/null
@@ -1 +0,0 @@
-#*.md
\ No newline at end of file
diff --git a/klipper-printer-sovol-sv06.cfg b/klipper-printer-sovol-sv06.cfg
deleted file mode 100644
index 8c55065..0000000
--- a/klipper-printer-sovol-sv06.cfg
+++ /dev/null
@@ -1,224 +0,0 @@
-# This file contains pin mappings for the stock Sovol SV06
-# To use this config, during "make menuconfig" select the 
-# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9) communication.
-# Also, since it is using the GD32F103, please select Disable SWD at startup
-
-# Flash this firmware by copying "out/klipper.bin" to a SD card and
-# turning on the printer with the card inserted. The firmware
-# filename must end in ".bin" and must not match the last filename
-# that was flashed.
-
-# See docs/Config_Reference.md for a description of parameters.
-
-[include ./macros/macros.cfg]
-[include ./macros/TEST_SPEED.cfg]
-[include ./macros/PARKING.cfg]
-[include ./macros/MECHANICAL_GANTRY_CALIBRATION.cfg]
-# Uncomment the following line if you're using an adxl345, and have it setup
-# [include ./adxl-rp2040.cfg]
-
-[mcu]
-# Obtain definition by "ls -l /dev/serial/by-id/"
-serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
-restart_method: command
-
-[printer]
-kinematics: cartesian
-max_velocity: 300
-max_accel: 3000
-max_accel_to_decel: 1500
-max_z_velocity: 5
-max_z_accel: 100
-# square_corner_velocity: 6.0
-
-#####################################################################
-#      X/Y Stepper Settings
-#####################################################################
-
-[stepper_x]
-step_pin: PC2
-dir_pin: !PB9
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: tmc2209_stepper_x:virtual_endstop
-position_endstop: 0
-position_max: 225
-homing_speed: 40
-homing_retract_dist: 0
-
-[tmc2209 stepper_x]
-uart_pin: PC1
-run_current: 0.860
-stealthchop_threshold: 0
-interpolate: False
-sense_resistor: 0.150
-uart_address: 3
-driver_SGTHRS: 81
-diag_pin: PA5
-
-[stepper_y]
-step_pin: PB8
-dir_pin: PB7
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 40
-endstop_pin: tmc2209_stepper_y:virtual_endstop
-position_endstop: 0
-position_max: 225
-homing_speed: 40
-homing_retract_dist: 0
-
-[tmc2209 stepper_y]
-uart_pin: PC0
-run_current: 0.900
-stealthchop_threshold: 0
-interpolate: False
-sense_resistor: 0.150
-uart_address: 3
-driver_SGTHRS: 82
-diag_pin: PA6
-
-#####################################################################
-#   Z Stepper Settings
-#####################################################################
-
-[stepper_z]
-step_pin: PB6
-dir_pin: !PB5
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 4
-endstop_pin: probe:z_virtual_endstop
-position_min: -4
-position_max: 261
-homing_speed: 4
-
-[tmc2209 stepper_z]
-uart_pin: PA15
-run_current: 1.000
-stealthchop_threshold: 0
-interpolate: False
-sense_resistor: 0.150
-uart_address: 3
-diag_pin: PA7
-
-#####################################################################
-#   Extruder
-#####################################################################
-
-[extruder]
-step_pin: PB4
-dir_pin: !PB3
-enable_pin: !PC3
-microsteps: 16
-rotation_distance: 4.56
-nozzle_diameter: 0.400
-filament_diameter: 1.750
-heater_pin: PA1
-sensor_type: sovol_thermistor
-sensor_pin: PC5
-min_temp: 0
-max_temp: 270
-min_extrude_temp: 190
-max_extrude_only_distance: 150.0
-
-[tmc2209 extruder]
-uart_pin: PC14
-run_current: 0.550
-stealthchop_threshold: 0
-interpolate: False
-sense_resistor: 0.150
-uart_address: 3
-
-#####################################################################
-#   Probe Related
-#####################################################################
-
-[probe]
-pin: PB1
-x_offset: 27
-y_offset: -20
-z_offset: 0
-speed: 7
-samples: 3
-samples_tolerance: 0.01
-samples_tolerance_retries: 10
-
-[safe_z_home]
-home_xy_position: 83,90
-speed: 60.0
-z_hop: 10
-z_hop_speed: 5
-
-[bed_mesh]
-speed: 120
-mesh_min: 30, 23
-mesh_max: 214, 214
-probe_count: 25
-algorithm: bicubic
-fade_start: 1
-fade_end: 10
-fade_target: 0
-
-#####################################################################
-#   Misc
-#####################################################################
-
-# [input_shaper]
-# shaper_freq_x: 46.948 
-# shaper_type_x: mzv
-# shaper_freq_y: 52.493
-# shaper_type_y: mzv
-# shaper_type: ei
-
-[virtual_sdcard]
-path: /home/pi/printer_data/gcodes
-
-[temperature_sensor mcu_temp]
-sensor_type: temperature_mcu
-min_temp: 25
-max_temp: 80
-
-[temperature_sensor raspberry_pi]
-sensor_type: temperature_host
-min_temp: 25
-max_temp: 80 
-
-[thermistor sovol_thermistor]
-temperature1: 25
-resistance1: 94162
-beta: 4160
-
-[heater_bed]
-heater_pin: PA2
-sensor_type: EPCOS 100K B57560G104F
-sensor_pin: PC4
-min_temp: 0
-max_temp: 110
-
-[fan]
-pin: PA0
-
-[display]
-lcd_type: st7920
-cs_pin: PB12
-sclk_pin: PB13
-sid_pin: PB15
-encoder_pins: ^PB14, ^PB10
-click_pin: ^!PB2
-
-#*# <---------------------- SAVE_CONFIG ---------------------->
-#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
-#*#
-#*# [extruder]
-#*# control = pid
-#*# pid_kp = 21.047
-#*# pid_ki = 1.477
-#*# pid_kd = 74.981
-#*#
-#*# [heater_bed]
-#*# control = pid
-#*# pid_kp = 71.224
-#*# pid_ki = 1.341
-#*# pid_kd = 945.503