Adjust PS config bundle.

misc/PrusaSlicer_config_bundle-SV06.ini

@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.6.0+linux-x64-GTK3 on 2023-08-23 at 04:27:23 UTC
+# generated by PrusaSlicer 2.6.0+linux-x64-GTK3 on 2023-08-23 at 19:39:14 UTC
 
 [print:0.20mm QUALITY SV06 Ellis]
 avoid_crossing_curled_overhangs = 0
@@ -149,7 +149,7 @@ support_tree_tip_diameter = 0.8
 support_tree_top_rate = 15%
 thick_bridges = 1
 thin_walls = 1
-threads = 4
+threads = 16
 top_fill_pattern = monotoniclines
 top_infill_extrusion_width = 0.4
 top_solid_infill_acceleration = 1000
@@ -176,187 +176,11 @@ wipe_tower_x = 170
 wipe_tower_y = 125
 xy_size_compensation = 0
 
-[print:Ellis_Decorative_45_Degree_15mm3]
-avoid_crossing_curled_overhangs = 0
-avoid_crossing_perimeters = 0
-avoid_crossing_perimeters_max_detour = 0
-bottom_fill_pattern = monotonic
-bottom_solid_layers = 3
-bottom_solid_min_thickness = 0.6
-bridge_acceleration = 3000
-bridge_angle = 0
-bridge_flow_ratio = 0.85
-bridge_speed = 140
-brim_separation = 0
-brim_type = outer_only
-brim_width = 0
-compatible_printers = 
-compatible_printers_condition = 
-complete_objects = 0
-default_acceleration = 3500
-dont_support_bridges = 1
-draft_shield = disabled
-elefant_foot_compensation = 0
-enable_dynamic_overhang_speeds = 0
-external_perimeter_acceleration = 750
-external_perimeter_extrusion_width = 0
-external_perimeter_speed = 80
-external_perimeters_first = 0
-extra_perimeters = 0
-extra_perimeters_on_overhangs = 0
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 115%
-fill_angle = 0
-fill_density = 10%
-fill_pattern = gyroid
-first_layer_acceleration = 1000
-first_layer_acceleration_over_raft = 0
-first_layer_extrusion_width = 125%
-first_layer_height = 0.3
-first_layer_speed = 30
-first_layer_speed_over_raft = 30
-fuzzy_skin = none
-fuzzy_skin_point_dist = 200
-fuzzy_skin_thickness = 150
-gap_fill_enabled = 1
-gap_fill_speed = 30
-gcode_comments = 0
-gcode_label_objects = 1
-gcode_resolution = 0
-gcode_substitutions = 
-infill_acceleration = 3500
-infill_anchor = 600%
-infill_anchor_max = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 0
-infill_first = 0
-infill_overlap = 25%
-infill_speed = 300
-inherits = 
-interface_shells = 0
-ironing = 0
-ironing_flowrate = 15%
-ironing_spacing = 0.1
-ironing_speed = 15
-ironing_type = top
-layer_height = 0.2
-max_print_speed = 300
-max_volumetric_extrusion_rate_slope_negative = 0
-max_volumetric_extrusion_rate_slope_positive = 0
-max_volumetric_speed = 15
-min_bead_width = 85%
-min_feature_size = 25%
-min_skirt_length = 20
-mmu_segmented_region_max_width = 0
-notes = 
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
-overhang_speed_0 = 15
-overhang_speed_1 = 15
-overhang_speed_2 = 20
-overhang_speed_3 = 25
-overhangs = 1
-perimeter_acceleration = 1000
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_generator = arachne
-perimeter_speed = 150
-perimeters = 3
-post_process = 
-print_settings_id = Ellis - Decorative 45 Degree (15mm3/s)
-raft_contact_distance = 0.1
-raft_expansion = 1.5
-raft_first_layer_density = 90%
-raft_first_layer_expansion = 3
-raft_layers = 0
-resolution = 0.0125
-seam_position = rear
-single_extruder_multi_material_priming = 1
-skirt_distance = 3
-skirt_height = 1
-skirts = 1
-slice_closing_radius = 0.049
-slicing_mode = regular
-small_perimeter_speed = 30
-solid_infill_acceleration = 3000
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 140%
-solid_infill_speed = 200
-spiral_vase = 0
-staggered_inner_seams = 0
-standby_temperature_delta = -5
-support_material = 1
-support_material_angle = 45
-support_material_auto = 1
-support_material_bottom_contact_distance = 0
-support_material_bottom_interface_layers = -1
-support_material_buildplate_only = 0
-support_material_closing_radius = 2
-support_material_contact_distance = 0.1
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_contact_loops = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_pattern = rectilinear
-support_material_interface_spacing = 0.2
-support_material_interface_speed = 100
-support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_speed = 120
-support_material_style = grid
-support_material_synchronize_layers = 0
-support_material_threshold = 30
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
-support_tree_angle = 40
-support_tree_angle_slow = 25
-support_tree_branch_diameter = 2
-support_tree_branch_diameter_angle = 5
-support_tree_branch_diameter_double_wall = 3
-support_tree_branch_distance = 1
-support_tree_tip_diameter = 0.8
-support_tree_top_rate = 15%
-thick_bridges = 1
-thin_walls = 1
-threads = 4
-top_fill_pattern = monotonic
-top_infill_extrusion_width = 101%
-top_solid_infill_acceleration = 1000
-top_solid_infill_speed = 60
-top_solid_layers = 5
-top_solid_min_thickness = 1
-travel_acceleration = 3500
-travel_speed = 300
-travel_speed_z = 0
-wall_distribution_count = 1
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 100%
-wipe_tower = 0
-wipe_tower_bridging = 10
-wipe_tower_brim_width = 2
-wipe_tower_cone_angle = 0
-wipe_tower_extra_spacing = 100%
-wipe_tower_extruder = 0
-wipe_tower_no_sparse_layers = 0
-wipe_tower_rotation_angle = 0
-wipe_tower_width = 60
-wipe_tower_x = 180
-wipe_tower_y = 140
-xy_size_compensation = 0
-
 [print:Ellis_Decorative_Standard_15mm3]
 avoid_crossing_curled_overhangs = 0
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
-bottom_fill_pattern = monotonic
+bottom_fill_pattern = monotoniclines
 bottom_solid_layers = 3
 bottom_solid_min_thickness = 0.6
 bridge_acceleration = 3000
@@ -375,26 +199,26 @@ draft_shield = disabled
 elefant_foot_compensation = 0
 enable_dynamic_overhang_speeds = 0
 external_perimeter_acceleration = 750
-external_perimeter_extrusion_width = 0
+external_perimeter_extrusion_width = 0.4
 external_perimeter_speed = 80
 external_perimeters_first = 0
 extra_perimeters = 0
-extra_perimeters_on_overhangs = 0
+extra_perimeters_on_overhangs = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
-extrusion_width = 115%
+extrusion_width = 0.46
 fill_angle = 45
 fill_density = 10%
-fill_pattern = gyroid
+fill_pattern = rectilinear
 first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
-first_layer_extrusion_width = 125%
+first_layer_extrusion_width = 0.5
-first_layer_height = 0.3
+first_layer_height = 0.26
 first_layer_speed = 30
 first_layer_speed_over_raft = 30
 fuzzy_skin = none
-fuzzy_skin_point_dist = 200
+fuzzy_skin_point_dist = 0.8
-fuzzy_skin_thickness = 150
+fuzzy_skin_thickness = 0.3
 gap_fill_enabled = 1
 gap_fill_speed = 30
 gcode_comments = 0
@@ -403,10 +227,10 @@ gcode_resolution = 0
 gcode_substitutions = 
 infill_acceleration = 3500
 infill_anchor = 600%
-infill_anchor_max = 0
+infill_anchor_max = 400%
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 0
+infill_extrusion_width = 0.46
 infill_first = 0
 infill_overlap = 25%
 infill_speed = 300
@@ -430,19 +254,19 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
-overhang_speed_0 = 15
+overhang_speed_0 = 75%
-overhang_speed_1 = 15
+overhang_speed_1 = 80%
-overhang_speed_2 = 20
+overhang_speed_2 = 90%
-overhang_speed_3 = 25
+overhang_speed_3 = 100%
 overhangs = 1
 perimeter_acceleration = 1000
 perimeter_extruder = 1
-perimeter_extrusion_width = 0
+perimeter_extrusion_width = 0.46
-perimeter_generator = arachne
+perimeter_generator = classic
 perimeter_speed = 150
 perimeters = 3
 post_process = 
-print_settings_id = Ellis - Decorative Standard (15mm3/s)
+print_settings_id = Ellis - Decorative Standard (15mm³)
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
@@ -461,7 +285,7 @@ solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 140%
+solid_infill_extrusion_width = 0.56
 solid_infill_speed = 200
 spiral_vase = 0
 staggered_inner_seams = 0
@@ -471,7 +295,7 @@ support_material_angle = 0
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
 support_material_bottom_interface_layers = -1
-support_material_buildplate_only = 0
+support_material_buildplate_only = 1
 support_material_closing_radius = 2
 support_material_contact_distance = 0.1
 support_material_enforce_layers = 0
@@ -486,7 +310,7 @@ support_material_interface_speed = 100
 support_material_pattern = rectilinear
 support_material_spacing = 3
 support_material_speed = 120
-support_material_style = grid
+support_material_style = organic
 support_material_synchronize_layers = 0
 support_material_threshold = 30
 support_material_with_sheath = 0
@@ -498,188 +322,12 @@ support_tree_branch_diameter_angle = 5
 support_tree_branch_diameter_double_wall = 3
 support_tree_branch_distance = 1
 support_tree_tip_diameter = 0.8
-support_tree_top_rate = 15%
+support_tree_top_rate = 30%
-thick_bridges = 1
+thick_bridges = 0
 thin_walls = 1
-threads = 4
+threads = 16
-top_fill_pattern = monotonic
+top_fill_pattern = monotoniclines
-top_infill_extrusion_width = 101%
+top_infill_extrusion_width = 0.4
-top_solid_infill_acceleration = 1000
-top_solid_infill_speed = 60
-top_solid_layers = 5
-top_solid_min_thickness = 1
-travel_acceleration = 3500
-travel_speed = 300
-travel_speed_z = 0
-wall_distribution_count = 1
-wall_transition_angle = 10
-wall_transition_filter_deviation = 25%
-wall_transition_length = 100%
-wipe_tower = 0
-wipe_tower_bridging = 10
-wipe_tower_brim_width = 2
-wipe_tower_cone_angle = 0
-wipe_tower_extra_spacing = 100%
-wipe_tower_extruder = 0
-wipe_tower_no_sparse_layers = 0
-wipe_tower_rotation_angle = 0
-wipe_tower_width = 60
-wipe_tower_x = 180
-wipe_tower_y = 140
-xy_size_compensation = 0
-
-[print:Ellis_PIF_45_Degree_15mm3]
-avoid_crossing_curled_overhangs = 0
-avoid_crossing_perimeters = 0
-avoid_crossing_perimeters_max_detour = 0
-bottom_fill_pattern = monotonic
-bottom_solid_layers = 5
-bottom_solid_min_thickness = 1
-bridge_acceleration = 3000
-bridge_angle = 0
-bridge_flow_ratio = 0.85
-bridge_speed = 140
-brim_separation = 0
-brim_type = outer_only
-brim_width = 0
-compatible_printers = 
-compatible_printers_condition = 
-complete_objects = 0
-default_acceleration = 3500
-dont_support_bridges = 1
-draft_shield = disabled
-elefant_foot_compensation = 0
-enable_dynamic_overhang_speeds = 0
-external_perimeter_acceleration = 750
-external_perimeter_extrusion_width = 101%
-external_perimeter_speed = 80
-external_perimeters_first = 0
-extra_perimeters = 0
-extra_perimeters_on_overhangs = 0
-extruder_clearance_height = 20
-extruder_clearance_radius = 20
-extrusion_width = 115%
-fill_angle = 0
-fill_density = 40%
-fill_pattern = grid
-first_layer_acceleration = 1000
-first_layer_acceleration_over_raft = 0
-first_layer_extrusion_width = 125%
-first_layer_height = 0.3
-first_layer_speed = 30
-first_layer_speed_over_raft = 30
-fuzzy_skin = none
-fuzzy_skin_point_dist = 200
-fuzzy_skin_thickness = 150
-gap_fill_enabled = 1
-gap_fill_speed = 30
-gcode_comments = 0
-gcode_label_objects = 1
-gcode_resolution = 0
-gcode_substitutions = 
-infill_acceleration = 3500
-infill_anchor = 600%
-infill_anchor_max = 0
-infill_every_layers = 1
-infill_extruder = 1
-infill_extrusion_width = 160%
-infill_first = 0
-infill_overlap = 25%
-infill_speed = 300
-inherits = 
-interface_shells = 0
-ironing = 0
-ironing_flowrate = 15%
-ironing_spacing = 0.1
-ironing_speed = 15
-ironing_type = top
-layer_height = 0.2
-max_print_speed = 300
-max_volumetric_extrusion_rate_slope_negative = 0
-max_volumetric_extrusion_rate_slope_positive = 0
-max_volumetric_speed = 15
-min_bead_width = 85%
-min_feature_size = 25%
-min_skirt_length = 20
-mmu_segmented_region_max_width = 0
-notes = 
-only_retract_when_crossing_perimeters = 1
-ooze_prevention = 0
-output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
-overhang_speed_0 = 15
-overhang_speed_1 = 15
-overhang_speed_2 = 20
-overhang_speed_3 = 25
-overhangs = 1
-perimeter_acceleration = 1000
-perimeter_extruder = 1
-perimeter_extrusion_width = 0
-perimeter_generator = arachne
-perimeter_speed = 150
-perimeters = 4
-post_process = 
-print_settings_id = Ellis - PIF 45 Degree (15mm3/s)
-raft_contact_distance = 0.1
-raft_expansion = 1.5
-raft_first_layer_density = 90%
-raft_first_layer_expansion = 3
-raft_layers = 0
-resolution = 0.0125
-seam_position = rear
-single_extruder_multi_material_priming = 1
-skirt_distance = 3
-skirt_height = 1
-skirts = 1
-slice_closing_radius = 0.049
-slicing_mode = regular
-small_perimeter_speed = 30
-solid_infill_acceleration = 3000
-solid_infill_below_area = 0
-solid_infill_every_layers = 0
-solid_infill_extruder = 1
-solid_infill_extrusion_width = 140%
-solid_infill_speed = 200
-spiral_vase = 0
-staggered_inner_seams = 0
-standby_temperature_delta = -5
-support_material = 0
-support_material_angle = 45
-support_material_auto = 1
-support_material_bottom_contact_distance = 0
-support_material_bottom_interface_layers = -1
-support_material_buildplate_only = 0
-support_material_closing_radius = 2
-support_material_contact_distance = 0.1
-support_material_enforce_layers = 0
-support_material_extruder = 1
-support_material_extrusion_width = 0
-support_material_interface_contact_loops = 0
-support_material_interface_extruder = 1
-support_material_interface_layers = 2
-support_material_interface_pattern = rectilinear
-support_material_interface_spacing = 0.2
-support_material_interface_speed = 100
-support_material_pattern = rectilinear
-support_material_spacing = 3
-support_material_speed = 120
-support_material_style = grid
-support_material_synchronize_layers = 0
-support_material_threshold = 30
-support_material_with_sheath = 0
-support_material_xy_spacing = 75%
-support_tree_angle = 40
-support_tree_angle_slow = 25
-support_tree_branch_diameter = 2
-support_tree_branch_diameter_angle = 5
-support_tree_branch_diameter_double_wall = 3
-support_tree_branch_distance = 1
-support_tree_tip_diameter = 0.8
-support_tree_top_rate = 15%
-thick_bridges = 1
-thin_walls = 1
-threads = 4
-top_fill_pattern = monotonic
-top_infill_extrusion_width = 101%
 top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
@@ -708,7 +356,7 @@ xy_size_compensation = 0
 avoid_crossing_curled_overhangs = 0
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
-bottom_fill_pattern = monotonic
+bottom_fill_pattern = monotoniclines
 bottom_solid_layers = 5
 bottom_solid_min_thickness = 1
 bridge_acceleration = 3000
@@ -727,26 +375,26 @@ draft_shield = disabled
 elefant_foot_compensation = 0
 enable_dynamic_overhang_speeds = 0
 external_perimeter_acceleration = 750
-external_perimeter_extrusion_width = 101%
+external_perimeter_extrusion_width = 0.4
 external_perimeter_speed = 80
 external_perimeters_first = 0
 extra_perimeters = 0
-extra_perimeters_on_overhangs = 0
+extra_perimeters_on_overhangs = 1
 extruder_clearance_height = 20
 extruder_clearance_radius = 20
-extrusion_width = 115%
+extrusion_width = 0.46
 fill_angle = 45
 fill_density = 40%
 fill_pattern = grid
 first_layer_acceleration = 1000
 first_layer_acceleration_over_raft = 0
-first_layer_extrusion_width = 125%
+first_layer_extrusion_width = 0.5
-first_layer_height = 0.3
+first_layer_height = 0.25
 first_layer_speed = 30
 first_layer_speed_over_raft = 30
 fuzzy_skin = none
-fuzzy_skin_point_dist = 200
+fuzzy_skin_point_dist = 0.8
-fuzzy_skin_thickness = 150
+fuzzy_skin_thickness = 0.3
 gap_fill_enabled = 1
 gap_fill_speed = 30
 gcode_comments = 0
@@ -755,10 +403,10 @@ gcode_resolution = 0
 gcode_substitutions = 
 infill_acceleration = 3500
 infill_anchor = 600%
-infill_anchor_max = 0
+infill_anchor_max = 400%
 infill_every_layers = 1
 infill_extruder = 1
-infill_extrusion_width = 160%
+infill_extrusion_width = 0.64
 infill_first = 0
 infill_overlap = 25%
 infill_speed = 300
@@ -782,19 +430,19 @@ notes =
 only_retract_when_crossing_perimeters = 1
 ooze_prevention = 0
 output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode
-overhang_speed_0 = 15
+overhang_speed_0 = 75%
-overhang_speed_1 = 15
+overhang_speed_1 = 80%
-overhang_speed_2 = 20
+overhang_speed_2 = 90%
-overhang_speed_3 = 25
+overhang_speed_3 = 100%
 overhangs = 1
 perimeter_acceleration = 1000
 perimeter_extruder = 1
-perimeter_extrusion_width = 0
+perimeter_extrusion_width = 0.4
-perimeter_generator = arachne
+perimeter_generator = classic
 perimeter_speed = 150
 perimeters = 4
 post_process = 
-print_settings_id = Ellis - PIF Standard (15mm3/s)
+print_settings_id = Ellis - PIF Standard (15mm³)
 raft_contact_distance = 0.1
 raft_expansion = 1.5
 raft_first_layer_density = 90%
@@ -813,7 +461,7 @@ solid_infill_acceleration = 3000
 solid_infill_below_area = 0
 solid_infill_every_layers = 0
 solid_infill_extruder = 1
-solid_infill_extrusion_width = 140%
+solid_infill_extrusion_width = 0.56
 solid_infill_speed = 200
 spiral_vase = 0
 staggered_inner_seams = 0
@@ -823,7 +471,7 @@ support_material_angle = 0
 support_material_auto = 1
 support_material_bottom_contact_distance = 0
 support_material_bottom_interface_layers = -1
-support_material_buildplate_only = 0
+support_material_buildplate_only = 1
 support_material_closing_radius = 2
 support_material_contact_distance = 0.1
 support_material_enforce_layers = 0
@@ -838,7 +486,7 @@ support_material_interface_speed = 100
 support_material_pattern = rectilinear
 support_material_spacing = 3
 support_material_speed = 120
-support_material_style = grid
+support_material_style = organic
 support_material_synchronize_layers = 0
 support_material_threshold = 30
 support_material_with_sheath = 0
@@ -850,12 +498,12 @@ support_tree_branch_diameter_angle = 5
 support_tree_branch_diameter_double_wall = 3
 support_tree_branch_distance = 1
 support_tree_tip_diameter = 0.8
-support_tree_top_rate = 15%
+support_tree_top_rate = 30%
-thick_bridges = 1
+thick_bridges = 0
 thin_walls = 1
-threads = 4
+threads = 16
-top_fill_pattern = monotonic
+top_fill_pattern = monotoniclines
-top_infill_extrusion_width = 101%
+top_infill_extrusion_width = 0.4
 top_solid_infill_acceleration = 1000
 top_solid_infill_speed = 60
 top_solid_layers = 5
@@ -2499,7 +2147,7 @@ z_offset = 0
 
 [physical_printer:Sv06]
 host_type = octoprint
-preset_name = Sovol Sv06
+preset_name = 
 preset_names = "Sovol Sv06"
 print_host = http://10.0.0.51/
 printer_technology = FFF
@@ -2512,9 +2160,9 @@ printhost_ssl_ignore_revoke = 0
 printhost_user = 
 
 [presets]
-print = Ellis_PIF_Standard_15mm3
+print = Ellis_Decorative_Standard_15mm3
 sla_print = 
 sla_material = 
 printer = Sovol Sv06
-filament = Eryone PETG - Blue
+filament = eSun PLA+ Blue
 physical_printer = Sv06