diff --git a/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini b/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini index 1fa1569..7b1d491 100644 --- a/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini +++ b/misc/PrusaSlicer_config_bundle-SV06-SV07-All.ini @@ -1,4 +1,4 @@ -# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2023-12-01 at 19:07:58 UTC +# generated by PrusaSlicer 2.6.1+linux-x64-GTK3 on 2023-12-01 at 20:34:38 UTC [print:0.20mm QUALITY SV06 Ellis] avoid_crossing_curled_overhangs = 0 @@ -708,183 +708,6 @@ wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 -[print:_Ellis_Decorative_Standard_24mm3_CoreXY-Speeds] -avoid_crossing_curled_overhangs = 0 -avoid_crossing_perimeters = 0 -avoid_crossing_perimeters_max_detour = 0 -bottom_fill_pattern = monotoniclines -bottom_solid_layers = 3 -bottom_solid_min_thickness = 0.6 -bridge_acceleration = 5000 -bridge_angle = 0 -bridge_flow_ratio = 0.85 -bridge_speed = 140 -brim_separation = 0 -brim_type = outer_only -brim_width = 0 -compatible_printers = -compatible_printers_condition = -complete_objects = 0 -default_acceleration = 4000 -dont_support_bridges = 1 -draft_shield = disabled -elefant_foot_compensation = 0 -enable_dynamic_overhang_speeds = 0 -external_perimeter_acceleration = 1000 -external_perimeter_extrusion_width = 0.4 -external_perimeter_speed = 80 -external_perimeters_first = 0 -extra_perimeters = 0 -extra_perimeters_on_overhangs = 1 -extruder_clearance_height = 20 -extruder_clearance_radius = 20 -extrusion_width = 0.46 -fill_angle = 45 -fill_density = 10% -fill_pattern = rectilinear -first_layer_acceleration = 2000 -first_layer_acceleration_over_raft = 0 -first_layer_extrusion_width = 0.5 -first_layer_height = 0.26 -first_layer_speed = 30 -first_layer_speed_over_raft = 30 -fuzzy_skin = none -fuzzy_skin_point_dist = 0.8 -fuzzy_skin_thickness = 0.3 -gap_fill_enabled = 1 -gap_fill_speed = 30 -gcode_comments = 0 -gcode_label_objects = 1 -gcode_resolution = 0 -gcode_substitutions = -infill_acceleration = 7000 -infill_anchor = 600% -infill_anchor_max = 400% -infill_every_layers = 1 -infill_extruder = 1 -infill_extrusion_width = 0.46 -infill_first = 0 -infill_overlap = 25% -infill_speed = 300 -inherits = -interface_shells = 0 -ironing = 0 -ironing_flowrate = 15% -ironing_spacing = 0.1 -ironing_speed = 15 -ironing_type = top -layer_height = 0.2 -max_print_speed = 300 -max_volumetric_extrusion_rate_slope_negative = 0 -max_volumetric_extrusion_rate_slope_positive = 0 -max_volumetric_speed = 24 -min_bead_width = 85% -min_feature_size = 25% -min_skirt_length = 20 -mmu_segmented_region_interlocking_depth = 0 -mmu_segmented_region_max_width = 0 -notes = -only_retract_when_crossing_perimeters = 1 -ooze_prevention = 0 -output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode -overhang_speed_0 = 75% -overhang_speed_1 = 80% -overhang_speed_2 = 90% -overhang_speed_3 = 100% -overhangs = 1 -perimeter_acceleration = 2000 -perimeter_extruder = 1 -perimeter_extrusion_width = 0.46 -perimeter_generator = arachne -perimeter_speed = 150 -perimeters = 3 -post_process = -print_settings_id = Ellis - Decorative Standard (15mm³) -raft_contact_distance = 0.1 -raft_expansion = 1.5 -raft_first_layer_density = 90% -raft_first_layer_expansion = 3 -raft_layers = 0 -resolution = 0.0125 -seam_position = aligned -single_extruder_multi_material_priming = 1 -skirt_distance = 3 -skirt_height = 1 -skirts = 1 -slice_closing_radius = 0.049 -slicing_mode = regular -small_perimeter_speed = 30 -solid_infill_acceleration = 5000 -solid_infill_below_area = 0 -solid_infill_every_layers = 0 -solid_infill_extruder = 1 -solid_infill_extrusion_width = 0.56 -solid_infill_speed = 200 -spiral_vase = 0 -staggered_inner_seams = 0 -standby_temperature_delta = -5 -support_material = 1 -support_material_angle = 0 -support_material_auto = 1 -support_material_bottom_contact_distance = 0 -support_material_bottom_interface_layers = -1 -support_material_buildplate_only = 1 -support_material_closing_radius = 2 -support_material_contact_distance = 0.1 -support_material_enforce_layers = 0 -support_material_extruder = 1 -support_material_extrusion_width = 0 -support_material_interface_contact_loops = 0 -support_material_interface_extruder = 1 -support_material_interface_layers = 2 -support_material_interface_pattern = rectilinear -support_material_interface_spacing = 0.2 -support_material_interface_speed = 100 -support_material_pattern = rectilinear -support_material_spacing = 3 -support_material_speed = 120 -support_material_style = organic -support_material_synchronize_layers = 0 -support_material_threshold = 30 -support_material_with_sheath = 0 -support_material_xy_spacing = 75% -support_tree_angle = 40 -support_tree_angle_slow = 25 -support_tree_branch_diameter = 2 -support_tree_branch_diameter_angle = 5 -support_tree_branch_diameter_double_wall = 3 -support_tree_branch_distance = 1 -support_tree_tip_diameter = 0.8 -support_tree_top_rate = 30% -thick_bridges = 0 -thin_walls = 1 -threads = 16 -top_fill_pattern = monotoniclines -top_infill_extrusion_width = 0.4 -top_solid_infill_acceleration = 2000 -top_solid_infill_speed = 60 -top_solid_layers = 5 -top_solid_min_thickness = 1 -travel_acceleration = 10000 -travel_speed = 300 -travel_speed_z = 0 -wall_distribution_count = 1 -wall_transition_angle = 10 -wall_transition_filter_deviation = 25% -wall_transition_length = 100% -wipe_tower = 0 -wipe_tower_bridging = 10 -wipe_tower_brim_width = 2 -wipe_tower_cone_angle = 0 -wipe_tower_extra_spacing = 100% -wipe_tower_extruder = 0 -wipe_tower_no_sparse_layers = 0 -wipe_tower_rotation_angle = 0 -wipe_tower_width = 60 -wipe_tower_x = 180 -wipe_tower_y = 140 -xy_size_compensation = 0 - [print:_Ellis_PIF_Standard_15mm3_CoreXY-Speeds] avoid_crossing_curled_overhangs = 0 avoid_crossing_perimeters = 0 @@ -1062,7 +885,184 @@ wipe_tower_x = 180 wipe_tower_y = 140 xy_size_compensation = 0 -[print:_Ellis_PIF_Standard_24mm3_CoreXY-Speeds] +[print:__Ellis_Decorative_Standard_24mm3_CoreXY-Speeds] +avoid_crossing_curled_overhangs = 0 +avoid_crossing_perimeters = 0 +avoid_crossing_perimeters_max_detour = 0 +bottom_fill_pattern = monotoniclines +bottom_solid_layers = 3 +bottom_solid_min_thickness = 0.6 +bridge_acceleration = 5000 +bridge_angle = 0 +bridge_flow_ratio = 0.85 +bridge_speed = 140 +brim_separation = 0 +brim_type = outer_only +brim_width = 0 +compatible_printers = +compatible_printers_condition = +complete_objects = 0 +default_acceleration = 4000 +dont_support_bridges = 1 +draft_shield = disabled +elefant_foot_compensation = 0 +enable_dynamic_overhang_speeds = 0 +external_perimeter_acceleration = 1000 +external_perimeter_extrusion_width = 0.4 +external_perimeter_speed = 80 +external_perimeters_first = 0 +extra_perimeters = 0 +extra_perimeters_on_overhangs = 1 +extruder_clearance_height = 20 +extruder_clearance_radius = 20 +extrusion_width = 0.46 +fill_angle = 45 +fill_density = 10% +fill_pattern = rectilinear +first_layer_acceleration = 2000 +first_layer_acceleration_over_raft = 0 +first_layer_extrusion_width = 0.5 +first_layer_height = 0.26 +first_layer_speed = 30 +first_layer_speed_over_raft = 30 +fuzzy_skin = none +fuzzy_skin_point_dist = 0.8 +fuzzy_skin_thickness = 0.3 +gap_fill_enabled = 1 +gap_fill_speed = 30 +gcode_comments = 0 +gcode_label_objects = 1 +gcode_resolution = 0 +gcode_substitutions = +infill_acceleration = 7000 +infill_anchor = 600% +infill_anchor_max = 400% +infill_every_layers = 1 +infill_extruder = 1 +infill_extrusion_width = 0.46 +infill_first = 0 +infill_overlap = 25% +infill_speed = 300 +inherits = +interface_shells = 0 +ironing = 0 +ironing_flowrate = 15% +ironing_spacing = 0.1 +ironing_speed = 15 +ironing_type = top +layer_height = 0.2 +max_print_speed = 300 +max_volumetric_extrusion_rate_slope_negative = 0 +max_volumetric_extrusion_rate_slope_positive = 0 +max_volumetric_speed = 24 +min_bead_width = 85% +min_feature_size = 25% +min_skirt_length = 20 +mmu_segmented_region_interlocking_depth = 0 +mmu_segmented_region_max_width = 0 +notes = +only_retract_when_crossing_perimeters = 1 +ooze_prevention = 0 +output_filename_format = [input_filename_base]-[printer_settings_id]-[filament_settings_id].gcode +overhang_speed_0 = 75% +overhang_speed_1 = 80% +overhang_speed_2 = 90% +overhang_speed_3 = 100% +overhangs = 1 +perimeter_acceleration = 2000 +perimeter_extruder = 1 +perimeter_extrusion_width = 0.46 +perimeter_generator = arachne +perimeter_speed = 150 +perimeters = 3 +post_process = +print_settings_id = Ellis - Decorative Standard (15mm³) +raft_contact_distance = 0.1 +raft_expansion = 1.5 +raft_first_layer_density = 90% +raft_first_layer_expansion = 3 +raft_layers = 0 +resolution = 0.0125 +seam_position = aligned +single_extruder_multi_material_priming = 1 +skirt_distance = 3 +skirt_height = 1 +skirts = 1 +slice_closing_radius = 0.049 +slicing_mode = regular +small_perimeter_speed = 30 +solid_infill_acceleration = 5000 +solid_infill_below_area = 0 +solid_infill_every_layers = 0 +solid_infill_extruder = 1 +solid_infill_extrusion_width = 0.56 +solid_infill_speed = 200 +spiral_vase = 0 +staggered_inner_seams = 0 +standby_temperature_delta = -5 +support_material = 1 +support_material_angle = 0 +support_material_auto = 1 +support_material_bottom_contact_distance = 0 +support_material_bottom_interface_layers = -1 +support_material_buildplate_only = 1 +support_material_closing_radius = 2 +support_material_contact_distance = 0.1 +support_material_enforce_layers = 0 +support_material_extruder = 1 +support_material_extrusion_width = 0 +support_material_interface_contact_loops = 0 +support_material_interface_extruder = 1 +support_material_interface_layers = 2 +support_material_interface_pattern = rectilinear +support_material_interface_spacing = 0.2 +support_material_interface_speed = 100 +support_material_pattern = rectilinear +support_material_spacing = 3 +support_material_speed = 120 +support_material_style = organic +support_material_synchronize_layers = 0 +support_material_threshold = 30 +support_material_with_sheath = 0 +support_material_xy_spacing = 75% +support_tree_angle = 40 +support_tree_angle_slow = 25 +support_tree_branch_diameter = 2 +support_tree_branch_diameter_angle = 5 +support_tree_branch_diameter_double_wall = 3 +support_tree_branch_distance = 1 +support_tree_tip_diameter = 0.8 +support_tree_top_rate = 30% +thick_bridges = 0 +thin_walls = 1 +threads = 16 +top_fill_pattern = monotoniclines +top_infill_extrusion_width = 0.4 +top_solid_infill_acceleration = 2000 +top_solid_infill_speed = 60 +top_solid_layers = 5 +top_solid_min_thickness = 1 +travel_acceleration = 10000 +travel_speed = 300 +travel_speed_z = 0 +wall_distribution_count = 1 +wall_transition_angle = 10 +wall_transition_filter_deviation = 25% +wall_transition_length = 100% +wipe_tower = 0 +wipe_tower_bridging = 10 +wipe_tower_brim_width = 2 +wipe_tower_cone_angle = 0 +wipe_tower_extra_spacing = 100% +wipe_tower_extruder = 0 +wipe_tower_no_sparse_layers = 0 +wipe_tower_rotation_angle = 0 +wipe_tower_width = 60 +wipe_tower_x = 180 +wipe_tower_y = 140 +xy_size_compensation = 0 + +[print:__Ellis_PIF_Standard_24mm3_CoreXY-Speeds] avoid_crossing_curled_overhangs = 0 avoid_crossing_perimeters = 0 avoid_crossing_perimeters_max_detour = 0 @@ -3221,7 +3221,7 @@ z_offset = 0 [physical_printer:Local SV06] host_type = octoprint -preset_name = +preset_name = Sovol SV06 preset_names = "Sovol SV06" print_host = http://10.0.0.51 printer_technology = FFF @@ -3235,7 +3235,7 @@ printhost_user = [physical_printer:Local SV06 Plus] host_type = octoprint -preset_name = +preset_name = Sovol SV06 Plus preset_names = "Sovol SV06 Plus" print_host = http://10.0.0.51 printer_technology = FFF @@ -3249,7 +3249,7 @@ printhost_user = [physical_printer:Local SV07] host_type = octoprint -preset_name = +preset_name = Sovol SV07 preset_names = "Sovol SV07" print_host = http://10.0.0.51 printer_technology = FFF @@ -3263,7 +3263,7 @@ printhost_user = [physical_printer:Local SV07 Plus] host_type = octoprint -preset_name = +preset_name = Sovol SV07 Plus preset_names = "Sovol SV07 Plus" print_host = http://10.0.0.51 printer_technology = FFF