diff --git a/README.md b/README.md
index dc42113..28ac243 100644
--- a/README.md
+++ b/README.md
@@ -1,9 +1,11 @@
 # 🚨 *One-Stop-Shop* Sovol SV06 Klipper Configuration
 
-This repository contains the Klipper configuration and firmware for the Sovol SV06 3D printer with completely *stock hardware*.
+This repository contains the Klipper configuration and firmware for the Sovol SV06 `PLUS` 3D printer with completely *stock hardware*.
 
 I am creating these files for my personal use and cannot be held responsible for what it might do to your printer. Use at your own risk.
 
+❗☠️ THIS BRANCH IS COMPLETELY UNTESTED ☠️❗
+
 # Highlights
 
 - 💥 This Klipper configuration is an *endpoint*, meaning that it contains **everything** that you could possibly need in order to have an excellent Klipper experience! 💥
@@ -158,7 +160,7 @@ This repository contains many files and folders. Some are *necessary* for this K
 
 ## FAQ
 
-##### How do I disable the beeping at the end of a print?
+##### ~~How do I disable the beeping at the end of a print?~~ Since the LCD doesn't work, likely the beeping will not work. I recommend not turning beeping on at this point.
 
 Make the following changes according to your needs. All beeping will be disabled except during gantry calibration.
 
diff --git a/cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg b/cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg
index f99852c..099ac2d 100644
--- a/cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg
+++ b/cfgs/MECHANICAL_GANTRY_CALIBRATION.cfg
@@ -72,16 +72,16 @@ gcode:
         SET_TMC_CURRENT STEPPER=stepper_z1 CURRENT={my_current} ; drop current
     {% endif %}
 
-    BEEP I=1
+    # BEEP I=1
     G4 P200 ; Probably not necessary, it is here just for sure
 
     SET_KINEMATIC_POSITION Z={z_max - 25} ; Trick printer into beleiving the gantry is 25mm lower than it is ; CHANGED
 
     G1 Z{z_max} F{6 * 60} ; based on above figures, there will be 20mm worth of grinding ; CHANGED
-    BEEP I=2
+    # BEEP I=2
     G4 P10000 ; wait 10 seconds
     G1 Z{z_max -6} F{6 * 60} ; move 4mm down
-    BEEP I=3
+    # BEEP I=3
     G4 P200 ; same as the first one
     
     SET_TMC_CURRENT STEPPER=stepper_z CURRENT={oldcurrent} HOLDCURRENT={oldhold}
diff --git a/cfgs/misc-macros.cfg b/cfgs/misc-macros.cfg
index 73ce691..527e2ad 100644
--- a/cfgs/misc-macros.cfg
+++ b/cfgs/misc-macros.cfg
@@ -21,7 +21,7 @@ gcode:
 
 [gcode_macro _globals]
 variable_filament_sensor_enabled: 0 # NOTE Enable(1) or disable(0) the filament sensor, if one is connected
-variable_beeping_enabled: 1 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
+variable_beeping_enabled: 0 # NOTE Enable(1) or disable(0) beeping everywhere except during gantry calibration
 variable_pre_purge_prime_length: 1.4
 gcode:
     SET_GCODE_VARIABLE MACRO=_globals VARIABLE=pre_purge_prime_length VALUE={ variable_pre_purge_prime_length }
diff --git a/printer.cfg b/printer.cfg
index 6a6e122..eb8f0e8 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -36,7 +36,7 @@ microsteps: 64
 rotation_distance: 40
 endstop_pin: tmc2209_stepper_x:virtual_endstop
 position_endstop: 0
-position_max: 223 # NOTE You can adjust this if you have more room
+position_max: 300 # NOTE You can adjust this if you have more room
 homing_speed: 40
 homing_retract_dist: 0
 
@@ -58,7 +58,7 @@ microsteps: 64
 rotation_distance: 40
 endstop_pin: tmc2209_stepper_y:virtual_endstop
 position_endstop: 0
-position_max: 223 # NOTE You can adjust this if you have more room
+position_max: 300 # NOTE You can adjust this if you have more room
 homing_speed: 40
 homing_retract_dist: 0
 
@@ -80,7 +80,7 @@ microsteps: 64
 rotation_distance: 4
 endstop_pin: probe:z_virtual_endstop
 position_min: -4
-position_max: 258 # NOTE You can adjust this if you have more room
+position_max: 340 # NOTE You can adjust this if you have more room
 homing_speed: 5
 
 [tmc2209 stepper_z]
@@ -179,13 +179,14 @@ pin: PA0
 #   Misc
 #####################################################################
 
-[display]
-lcd_type: st7920
-cs_pin: PB12
-sclk_pin: PB13
-sid_pin: PB15
-encoder_pins: ^PB14, ^PB10
-click_pin: ^!PB2
+# NOTE Apparently the screen is not Klipper friendly
+# [display]
+# lcd_type: st7920
+# cs_pin: PB12
+# sclk_pin: PB13
+# sid_pin: PB15
+# encoder_pins: ^PB14, ^PB10
+# click_pin: ^!PB2
 
 [bed_screws]
 screw1: 26.5, 31
@@ -212,12 +213,13 @@ speed: 50
 horizontal_move_z: 10
 screw_thread: CCW-M4
 
-[output_pin beeper]
-pin: PC6
-value: 0
-shutdown_value: 0
-pwm: True
-cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
+# NOTE The speaker will probably not work, since the LCD apparently doesn't work with Klipper
+# [output_pin beeper]
+# pin: PC6
+# value: 0
+# shutdown_value: 0
+# pwm: True
+# cycle_time: 0.0005 ; Default beeper tone in kHz. 1 / 0.0005 = 2000Hz (2kHz)
 
 [filament_switch_sensor filament_sensor]
 switch_pin: !PA4 # "Pulled-high"