From 49b3af64917ca8d1c64f7f8a1e5b51ab78feea49 Mon Sep 17 00:00:00 2001 From: bassamanator Date: Thu, 18 Jan 2024 02:25:51 -0500 Subject: [PATCH] Adjust FAQs. --- README.md | 38 +++++++++++++++----------------------- 1 file changed, 15 insertions(+), 23 deletions(-) diff --git a/README.md b/README.md index 00e5eb5..73c8ef1 100644 --- a/README.md +++ b/README.md @@ -72,7 +72,7 @@ In many ways, this entire repository can be considered _my opinion_ on the `3D p ## Before You Begin -- This entire page is a **12 minute read**. Save yourself _hours of troubleshooting_ and read this documentation fully. +- This entire page is a **11 minute read**. Save yourself _hours of troubleshooting_ and read this documentation fully. - ⚠️ Make sure your printer is in good physical condition, because print and travel speeds will be _a lot faster_. Beginners would be wise to run through [these steps](https://github.com/bassamanator/everything-sovol-sv06/blob/main/initialsteps.md). - ⚠️ [Disable](https://github.com/bassamanator/everything-sovol-sv06/blob/main/howto.md#disable-usb-cable-5v-pin) the USB cable's 5V pin. - Follow the steps in order. If an error was reported at a step, do no proceed to the next step. @@ -86,6 +86,7 @@ In many ways, this entire repository can be considered _my opinion_ on the `3D p - It is assumed that there is one instance of Klipper installed. If that is not the case, the steps in this guide will not work _perfectly_ for you. - Your question has probably been answered already, but if it hasn't, please post in the [Discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions) section. - I would recommend searching for the word `NOTE` in this configuration. There are roughly half a dozen short points amongst the various files that you should be aware of. + [🔼 Back to top](#outline) @@ -281,11 +282,23 @@ This repository contains many files and folders. Some are _necessary_ for this K ## FAQ +### What are some settings that I can change? + +| File | Section | +| ---------------------- | ------------------------ | +| `cfgs/misc-macros.cfg` | `[gcode_macro _globals]` | + +| Variable | Disable | Enable | Notes | +| ---------------------------------- | ------------- | ------------- | ------------------------------------------------------------------- | +| `variable_beeping_enabled` | `0` | `1` (default) | +| `variable_filament_sensor_enabled` | `0` (default) | `1` | +| `variable_kamp_enable` | `0` (default) | `1` | See [here](#how-do-i-enable-kamp-klipper-adaptive-meshing--purging) | + ### How do I import a configuration bundle into SuperSlicer/PrusaSlicer? Please see this [discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions/13). -### How do I print using SuperSlicer? +### How do I print using SuperSlicer/PrusaSlicer? Please see this [discussion](https://github.com/bassamanator/Sovol-SV06-firmware/discussions/14). @@ -298,24 +311,10 @@ The printer will beep upon: - Upon `PRINT_END`. - `MECHANICAL_GANTRY_CALIBRATION`/`G34`. -| File | `cfgs/misc-macros.cfg` | -| -------- | -------------------------- | -| Section | `[gcode_macro _globals]` | -| Variable | `variable_beeping_enabled` | -| Disable | `0` | -| Enable | `1` (default) | - ### I want to use a filament sensor. How do I set it up? You can find information about the physical setup [here](https://github.com/bassamanator/everything-sovol-sv06#filament-sensor). -| File | `cfgs/misc-macros.cfg` | -| -------- | ---------------------------------- | -| Section | `[gcode_macro _globals]` | -| Variable | `variable_filament_sensor_enabled` | -| Disable | `0` (default) | -| Enable | `1` | - ### My filament runout sensor works, but I just started a print without any filament loaded. What gives? A simple runout sensor can only detect a change in state. So, if you start a print without filament loaded, the printer will not know that there is no filament loaded. You should test your sensor by having filament loaded, starting a print, then cutting the filament. The expected behaviour is that the print will pause, and as long as you have beeping enabled, you will hear 3 annoying beeps. @@ -360,13 +359,6 @@ The printhead is now parked front center waiting for you to insert filament. You This repo contains all the code from the KAMP repository, however, only the `adaptive meshing` and `LINE_PURGE` functionality of KAMP has been configured and tested for use. To enable other functionality, adjust `/cfgs/kamp/KAMP_Settings.cfg`. -| File | `cfgs/misc-macros.cfg` | -| -------- | ------------------------ | -| Section | `[gcode_macro _globals]` | -| Variable | `variable_kamp_enable` | -| Disable | `0` (default) | -| Enable | `1` | - ### How do I use the `TEST_SPEED` macro? ⚠️ This is for advanced users only, with well oiled machines. You can cause serious damage to your printer if you're not careful. ☠️ **You have been warned** ☠️.