PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-08 21:41:15 +00:00
Code Issues Packages Projects Releases Wiki Activity

Adjusted plus instructions.

Browse Source
This commit is contained in:
Bassam Husain
2023-04-06 06:42:20 -04:00
parent 0358cb6304 4b90c7abc5
commit 3c98d99665
1 changed files with 15 additions and 11 deletions
Download Patch File Download Diff File Expand all files Collapse all files

26
README.md
View File

@@ -107,21 +107,25 @@ You can choose *either* of the 2 following methods.
💡 I recommend no filament be loaded for any of these steps. 💡 I recommend no filament be loaded for any of these steps.
1. Do a `G28`; home all. 💡 Find explainations for gcode commands at [https://marlinfw.org/](https://marlinfw.org/) and [klipper.org](https://www.klipper3d.org/G-Codes.html).
1. Check to see if `X` and `Y` max positions (`G1 X223 F3000`, `G1 Y223 F3000`) can be reached, and adjust `position_max`, if necessary. You can probably go all the way up to `225` for `X` and `Y` both, however, I would not recommend it.
2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up agaisnt the `stoppers` at the top. You will hear a succession of beeps. 1. `G28`
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam. The range is 250 to 261 from what I've seen, could be even higher for you. Adjust `position_max`, if necessary. I can go all the way to 258 over and over again, however, I would not print anything higher than 255 probably. 1. Check to see if `X` and `Y` max positions (`G90`, `G1 X300 F3000`, `G1 Y300 F3000`) can be reached, and adjust `position_max`, if necessary. Note, you might be able to go even further.
2. Do a `G34`; mechanical gantry calibration. After the controlled collision against the beam at the top, there will be a 10 second pause for you to verify that both sides of the gantry are pressed up agaisnt the `stoppers` at the top. ~~You will hear a succession of beeps.~~
1. Figure out your `Z` `position_max` by baby stepping your way up to the beam (`G90`, `G1 Z330 F900`, then move up mm by mm). Adjust `position_max`, if necessary.
3. Pid tune the bed, but first move the printhead to the center. Ideally, all Pid tuning should occur at the temperatures that you print most at. 3. Pid tune the bed, but first move the printhead to the center. Ideally, all Pid tuning should occur at the temperatures that you print most at.
1. `G28` 1. `G28`
2. `G1 X111 Y111 Z40 F6000` 2. `G90`
3. `PID_CALIBRATE HEATER=heater_bed TARGET=70` 3. `G1 X150 Y150 Z40 F6000`
4. `SAVE_CONFIG` (once completed) 4. `PID_CALIBRATE HEATER=heater_bed TARGET=70`
5. `SAVE_CONFIG` (once completed)
4. Pid tune the extruder while part cooling fan runs at 25%. 4. Pid tune the extruder while part cooling fan runs at 25%.
1. `G28` 1. `G28`
2. `G1 X111 Y111 Z10 F6000` 2. `G90`
3. `M106 S64` 3. `G1 X150 Y150 Z10 F6000`
4. `PID_CALIBRATE HEATER=extruder TARGET=245` 4. `M106 S64`
5. `SAVE_CONFIG` (once completed) 5. `PID_CALIBRATE HEATER=extruder TARGET=245`
6. `SAVE_CONFIG` (once completed)
5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test). 5. Adjust `z_offset`. Make sure your nozzle if very clean. Do the [Paper test](https://www.klipper3d.org/Bed_Level.html?h=probe_calibrate#the-paper-test).
1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60` 1. `SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=60`
2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180` 2. `SET_HEATER_TEMPERATURE HEATER=extruder TARGET=180`