diff --git a/printer.cfg b/printer.cfg
index 2c0e6d5..99a3a09 100644
--- a/printer.cfg
+++ b/printer.cfg
@@ -141,13 +141,14 @@ pin: PB1
 x_offset: 27
 y_offset: -20
 # z_offset: 0
-samples: 5
-samples_result: median
+samples: 3
+# samples_result: median
 samples_tolerance: 0.01
 samples_tolerance_retries: 5
 
 [safe_z_home]
-home_xy_position: 0, 223 # NOTE 111.50,111.50
+# home_xy_position: 0, 223 # NOTE 111.50,111.50
+home_xy_position: 84.50, 135 # X:84.500 Y:135.000
 speed: 100.0
 z_hop: 10
 z_hop_speed: 15
@@ -160,8 +161,8 @@ probe_count: 5,5
 algorithm: bicubic
 fade_start: 1
 fade_end: 10
-# NOTE fade_target: 0
-relative_reference_index: 20 # NOTE
+fade_target: 0 # NOTE
+# relative_reference_index: 20 # NOTE
 
 [virtual_sdcard]
 path: /home/pi/printer_data/gcodes
@@ -234,25 +235,6 @@ screw_thread: CCW-M4
 #*# [probe]
 #*# z_offset = 1.550
 #*#
-#*# [bed_mesh default]
-#*# version = 1
-#*# points =
-#*# 	0.210625, 0.309375, 0.357500, 0.312500, 0.247500
-#*# 	0.218125, 0.330000, 0.409375, 0.385625, 0.313750
-#*# 	0.184375, 0.328125, 0.420625, 0.428125, 0.378750
-#*# 	0.086250, 0.257500, 0.386250, 0.418750, 0.392500
-#*# 	0.000000, 0.211250, 0.363125, 0.420000, 0.420000
-#*# x_count = 5
-#*# y_count = 5
-#*# mesh_x_pps = 2
-#*# mesh_y_pps = 2
-#*# algo = bicubic
-#*# tension = 0.2
-#*# min_x = 27.0
-#*# max_x = 222.0
-#*# min_y = 5.0
-#*# max_y = 203.0
-#*#
 #*# [bed_mesh default1]
 #*# version = 1
 #*# points =
@@ -271,3 +253,41 @@ screw_thread: CCW-M4
 #*# max_x = 222.0
 #*# min_y = 5.0
 #*# max_y = 203.0
+#*#
+#*# [bed_mesh default-working]
+#*# version = 1
+#*# points =
+#*# 	0.210625, 0.309375, 0.357500, 0.312500, 0.247500
+#*# 	0.218125, 0.330000, 0.409375, 0.385625, 0.313750
+#*# 	0.184375, 0.328125, 0.420625, 0.428125, 0.378750
+#*# 	0.086250, 0.257500, 0.386250, 0.418750, 0.392500
+#*# 	0.000000, 0.211250, 0.363125, 0.420000, 0.420000
+#*# min_x = 27.0
+#*# max_x = 222.0
+#*# min_y = 5.0
+#*# max_y = 203.0
+#*# x_count = 5
+#*# y_count = 5
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = bicubic
+#*# tension = 0.2
+#*#
+#*# [bed_mesh default-v1]
+#*# version = 1
+#*# points =
+#*# 	  -0.030625, -0.042500, -0.038750, -0.058750, -0.120625
+#*# 	  -0.050417, -0.068542, -0.046875, -0.056250, -0.125417
+#*# 	  -0.095000, -0.072500, -0.057917, -0.052292, -0.110417
+#*# 	  -0.091250, -0.052500, -0.028125, -0.030625, -0.086667
+#*# 	  -0.021667, 0.030000, 0.070208, 0.073125, 0.025833
+#*# x_count = 5
+#*# y_count = 5
+#*# mesh_x_pps = 2
+#*# mesh_y_pps = 2
+#*# algo = bicubic
+#*# tension = 0.2
+#*# min_x = 27.0
+#*# max_x = 222.0
+#*# min_y = 5.0
+#*# max_y = 203.0