From 1386f8324080ef354a66f61a9f5d6515d199a125 Mon Sep 17 00:00:00 2001 From: bassamanator Date: Sun, 14 Jan 2024 20:34:24 -0500 Subject: [PATCH] Minor adjustments to instructions. --- README.md | 18 ++++++++++-------- 1 file changed, 10 insertions(+), 8 deletions(-) diff --git a/README.md b/README.md index a0815e6..b68ec96 100644 --- a/README.md +++ b/README.md @@ -125,10 +125,10 @@ Please note: ### Download OSS Klipper Configuration -You can choose _either_ of the 2 following methods. - #### Method 1: Clone the Repository +💡 Make sure `git` is installed (`sudo apt update && sudo apt install git`). + 1. `cd ~/printer_data/config` 2. Empty entire `~/printer_data/config` folder. - In linux, you can delete files via `rm fileName` and directories via `rmdir directoryName`. @@ -148,6 +148,8 @@ You can choose _either_ of the 2 following methods. ### Adjust Configuration with MCU Path +💡 Make sure the host and printer are connected via USB. + 1. Find what port the `mcu` (printer motherboard) is connected to via **one** of the following commands: - `ls /dev/serial/by-id/*` @@ -159,7 +161,7 @@ You can choose _either_ of the 2 following methods. 2. Adjust the `[mcu]` section in `printer.cfg` accordingly. ```yaml - # 🗒️ This is just an example + # 📝 This is just an example [mcu] serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0 restart_method: command @@ -183,7 +185,7 @@ If the Klipper flash that you did earlier was successful, and you've done everyt 💡 I recommend no filament be loaded for any of these steps. -🗒️ You will be pasting/typing these commands into the `Mainsail`/`Fluidd` console. +📝 You will be pasting/typing these commands into the `Mainsail`/`Fluidd` console. 1. Check to see if `X` and `Y` max positions can be reached, and adjust `position_max`, if necessary. You might be able to go further, which is great, but I recommend leaving a 2mm gap for safety. 1. `G28` @@ -214,7 +216,7 @@ But first, adjust your slicer. ## Adjust Your Slicer -🗒️ If you are using the config bundles found on this repo, you can skip this section. +📝 If you are using the config bundles found on this repo, you can skip this section. ### Start G-Code @@ -234,7 +236,7 @@ If you would like to print a purge line before your print starts, at the end of - `LINE_PURGE`; prints KAMP's purge line. ⚠️ Do not attempt to use without reading [this section](#how-do-i-enable-kamp-klipper-adaptive-meshing--purging). ```yaml -# 🗒️ This is just an example Start G-Code +# 📝 This is just an example Start G-Code PRINT_START ... PURGE_LINE ``` @@ -355,9 +357,9 @@ The printhead is now parked front center waiting for you to insert filament. You ⚠️ If KAMP is disabled, and there is no `default` mesh, `PRINT_START` will crash. -🗒️ The [Label objects setting](https://docs.mainsail.xyz/overview/features/exclude-objects#enable-the-label-objects-setting-in-your-slicer) in your slicer must be enabled for KAMP to work. +📝 The [Label objects setting](https://docs.mainsail.xyz/overview/features/exclude-objects#enable-the-label-objects-setting-in-your-slicer) in your slicer must be enabled for KAMP to work. -🗒️ `LINE_PURGE` is useable (on appropriate devices) even if KAMP is disabled. +📝 `LINE_PURGE` is useable (on appropriate devices) even if KAMP is disabled. This repo contains all the code from the KAMP repository, however, only the `adaptive meshing` and `LINE_PURGE` functionality of KAMP has been configured and tested for use. To enable other functionality, adjust `/cfgs/kamp/KAMP_Settings.cfg`.