PublicArchives/Sovol-SV06-firmware
1
0
Fork 0
mirror of https://github.com/bassamanator/Sovol-SV06-firmware.git synced 2025-11-08 21:41:15 +00:00
Code Issues Packages Projects Releases Wiki Activity

Adjust readme.

Browse Source
This commit is contained in:
Bassam Husain
2023-11-19 20:36:24 -05:00
parent fddbbc2acc
commit 122c5a1d3a
1 changed files with 16 additions and 8 deletions
Download Patch File Download Diff File Expand all files Collapse all files

22
README.md
View File

@@ -62,7 +62,7 @@ Although I've made switching over to Klipper as easy as is possible, it can stil
## Before You Begin
- Read this documentation _fully!_
- This entire page is a **13 minute read**. Save yourself _hours of troubleshooting_ and read this documentation **fully!**
- Make sure your printer is in good physical condition, because print and travel speeds will be _a lot faster_ than they were before. Beginner's would be wise to go through the steps mentioned [here](https://github.com/bassamanator/everything-sovol-sv06/blob/main/initialsteps.md). Consider yourself warned.
- Follow the steps in order.
- If an error was reported at a step, do no proceed to the next step.
@@ -130,14 +130,18 @@ You can choose _either_ of the 2 following methods.
### Adjust Configuration with MCU Path
1. Find what port the `mcu` (printer motherboard) is connected to via `ls -l /dev/serial/by-id/` or `ls -l /dev/serial/by-path/`.
1. Find what port the `mcu` (printer motherboard) is connected to via **one** of the following commands:
- `ls /dev/serial/by-id/*`
- `ls /dev/serial/by-path/*`
1. The output will be something along the lines of
`lrwxrwxrwx 13 root root 22 Apr 11:10 usb-1a86_USB2.0-Serial-if00-port0 -> ../../ttyUSB0`.
2. `usb-1a86_USB2.0-Serial-if00-port0` is the relevant part.
3. Therefore, the full path to your `mcu` is either `/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0` or `/dev/serial/by-path/usb-1a86_USB2.0-Serial-if00-port0`, depending on the command you used to find the `mcu`.
2. Adjust the `[mcu]` section in `printer.cfg` accordingly. 🗒️ This is just an **example**:
- `/dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0`
2. Adjust the `[mcu]` section in `printer.cfg` accordingly.
```yaml
🗒️ This is just an example
[mcu]
serial: /dev/serial/by-id/usb-1a86_USB2.0-Serial-if00-port0
restart_method: command
@@ -153,9 +157,13 @@ If the Klipper flash that you did earlier was successful, and you've done everyt
❗☠️ **Power off if there is a collision/problem** ☠️❗
💡 The `emergency stop` button in your dashboard works faster than hitting the power switch.
💡 Do a practice emergency stop.
💡 I recommend no filament be loaded for any of these steps.
🗒️ Find explanations for gcode commands at [https://marlinfw.org/](https://marlinfw.org/) and [https://www.klipper3d.org/](https://www.klipper3d.org/G-Codes.html).
🗒️ Find explanations for gcode commands: [https://marlinfw.org/](https://marlinfw.org/), [https://www.klipper3d.org/](https://www.klipper3d.org/G-Codes.html).
You will be pasting/typing these commands into the Mainsail/Fluidd console.